TRANSMISSION CONTROL CABLE > INSTALLATION |
| 1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for LHD) |
Pass the transmission control cable assembly from the cabin to the engine compartment.
Install the transmission control cable assembly with the 2 bolts.
Install the dash panel insulator to the original position.
Connect the transmission control cable assembly to the 2 transmission control cable brackets.
Install a new clip to the No. 1 transmission control cable bracket.
![]() |
Install the transmission control cable assembly to the No. 1 transmission control cable bracket
| *1 | No. 1 Transmission control cable assembly |
| *2 | No. 1 transmission control cable bracket |
| *a | Claw A |
| *b | Claw B |
Connect the transmission control cable assembly to the control shaft lever with the nut.
Engage the 2 claws to connect the transmission control cable assembly.
![]() |
Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.
| *1 | Slider |
| *2 | Lock Piece |
| *a | Slide |
| *b | Pull |
![]() |
Install the end of transmission control cable assembly to the lower shift lever assembly.
| *1 | Lock Piece |
Push the lock piece into the adjuster case.
| 2. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for RHD) |
Pass the transmission control cable assembly from the cabin to the engine compartment.
Install the transmission control cable assembly with the 2 bolts.
Install the dash panel insulator to the original position.
Install the No. 1 parking brake cable assembly with the bolt.
Install the floor carpet to the original position.
Connect the transmission control cable assembly to the 2 transmission control cable brackets.
Install a new clip to the control cable bracket.
![]() |
Install the transmission control cable assembly to the No. 1 transmission control cable bracket
| *1 | Transmission control cable assembly |
| *2 | No. 1 transmission control cable bracket |
| *a | Claw A |
| *b | Claw B |
Connect the transmission control cable to the control shaft lever with the nut.
Engage the 2 claws to connect the transmission control cable assembly.
![]() |
Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.
| *1 | Slider |
| *2 | Lock Piece |
| *a | Slide |
| *b | Pull |
![]() |
Install the end of transmission control cable to the lower shift lever assembly.
| *1 | Lock Piece |
Push the lock piece into the adjuster case.
| 3. CONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY (for LHD) |
Install the No. 1 parking brake cable assembly with the bolt and nut.
Install the floor carpet to the original position.
| 4. INSTALL ACCELERATOR PEDAL SENSOR ASSEMBLY (for LHD) |
| 5. INSTALL AIRBAG SENSOR ASSEMBLY |
| 6. INSTALL AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Insert the projection of the air cleaner case sub-assembly to the hole of the No. 2 air cleaner bracket as shown in the illustration.
| *a | Projection |
Tighten the 2 bolts.
| 7. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| 8. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
Install the air cleaner hose with the hose clamp.
![]() |
Connect the 2 fuel vapor feed hoses.
| *1 | Retainer |
| *a | Push |
Install the air cleaner cap sub-assembly with the 2 clamps.
Connect the connector.
Connect the ventilation hose to the cylinder head cover.
Connect the mass air flow meter connector and wire harness clamp to the air cleaner cap sub-assembly.
| 9. INSTALL INLET AIR CLEANER ASSEMBLY |
Install the inlet air cleaner with the 2 bolts.
| 10. INSTALL COOL AIR INTAKE DUCT SEAL |
Install the cool air intake duct seal with the 9 clips.
| 11. INSPECT SHIFT LEVER POSITION |
While moving the shift lever from the N position to each position, check that the lever moves smoothly and that the shift position indicator comes on properly according to the shift lever position.
Put the vehicle into the READY-on state and check the following:
When the shift lever is moved to the D position, the vehicle moves forward.
When the shift lever is moved to the R position, the vehicle moves in reverse.
| 12. ADJUST SHIFT LEVER POSITION |
Move the shift lever to N.
Remove the console box (Click here).
![]() |
Disconnect the end of the transmission control cable assembly from the lower shift lever assembly.
![]() |
Slide the slider of the transmission control cable assembly in the direction indicated by the arrow and pull the lock piece outward.
| *1 | Slider |
| *2 | Lock Piece |
| *a | Slide |
| *b | Pull |
![]() |
Install the end of the transmission control cable assembly to the lower shift lever assembly.
| *1 | Lock Piece |
Push the lock piece into the adjuster case.
After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.
Install the console box (Click here).