TRANSMISSION CONTROL CABLE > REMOVAL |
| 1. REMOVE COOL AIR INTAKE DUCT SEAL |
![]() |
Remove the 9 clips and cool air intake duct seal.
| 2. REMOVE INLET AIR CLEANER ASSEMBLY |
![]() |
Remove the 2 bolts and inlet air cleaner assembly.
| 3. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Disconnect the mass air flow meter connector and wire harness clamp from the air cleaner cap sub-assembly.
Disconnect the ventilation hose from the cylinder head cover.
Disconnect the connector.
![]() |
Release the 2 clamps and remove the air cleaner cap sub-assembly.
![]() |
Disconnect the 2 fuel vapor feed hoses.
| *1 | Retainer |
| *2 | Fuel Tube Connector |
| *3 | Pipe |
| *4 | O-ring |
| *a | Pull |
![]() |
Loosen the hose clamp and disconnect the air cleaner hose from the throttle with motor body assembly.
| 4. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| 5. REMOVE AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and air cleaner case sub-assembly.
| *a | Projection |
| 6. REMOVE AIRBAG SENSOR ASSEMBLY |
| 7. REMOVE ACCELERATOR PEDAL SENSOR ASSEMBLY |
![]() |
Disconnect the connector.
| *a | for LHD: |
| *b | for RHD: |
Remove the 2 bolts and accelerator pedal sensor assembly.
| 8. DISCONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY (for LHD) |
Turn back the floor carpet.
![]() |
Remove the bolt and nut, and disconnect the No. 1 parking brake cable assembly.
| 9. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY (for LHD) |
Move the shift lever to N.
![]() |
Disconnect the end of the transmission control cable from the lower shift lever assembly.
Disengage the 2 claws and disconnect the transmission control cable assembly from the lower shift lever assembly.
![]() |
Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.
Using a screwdriver, disengage the 4 claws and disconnect the transmission control cable assembly with clip from the No. 1 transmission control cable bracket.
Remove the clip from the transmission control cable assembly.
![]() |
Disconnect the transmission control cable assembly from the 2 transmission control cable brackets.
![]() |
Remove the bolt and disconnect the No. 1 parking brake cable assembly from the body.
| *1 | No. 1 parking brake cable assembly |
| *2 | Transmission control cable assembly |
Turn back the dash panel insulator.
Remove the 2 bolts and pull out the transmission control cable assembly from the body.
| 10. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY (for RHD) |
Move the shift lever to N.
![]() |
Disconnect the end of transmission control cable assembly from the lower shift lever assembly.
Disengage the 2 claws and disconnect the transmission control cable assembly from the lower shift lever assembly.
![]() |
Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.
Using a screwdriver, disengage the 4 claws and disconnect the transmission control cable assembly with clip from the No. 1 transmission control cable bracket.
Remove the clip from the transmission control cable assembly.
![]() |
Disconnect the transmission control cable assembly from the 2 transmission control cable brackets.
![]() |
Remove the bolt and disconnect the No. 1 parking brake cable assembly from the body.
| *1 | No. 1 parking brake cable assembly |
| *2 | Transmission control cable assembly |
Turn back the dash panel insulator.
Remove the 2 bolts and pull out the transmission control cable assembly from the body.