SHIFT LEVER > INSTALLATION |
| 1. INSTALL SHIFT LEVER SUPPORT |
![]() |
Install the shift lever support with the 4 bolts in the sequence shown in the illustration.
| 2. INSTALL LOWER SHIFT LEVER ASSEMBLY |
![]() |
Install the lower shift lever assembly with the 4 bolts in the sequence shown in the illustration.
Connect the 3 clamps and connector.
![]() |
Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.
| *1 | Slider |
| *2 | Lock Piece |
| *a | Slide |
| *b | Pull |
![]() |
Install the end of the transmission control cable to the shift lever assembly.
| *1 | Lock Piece |
Push the lock piece into the adjuster case.
| 3. INSTALL NO. 1 CONSOLE BOX DUCT |
Install the No. 1 console box duct to the lower shift lever assembly with the clip.
| 4. INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET |
Install the No. 1 console box mounting bracket to the lower shift lever assembly with the screw.
| 5. INSTALL FLOOR CARPET BRACKET LH |
Engage the 2 guides.
Install the floor carpet bracket LH with the 2 clips.
| 6. INSTALL CONSOLE BOX INSERT |
for RHD:
Engage the 2 claws to connect the room temperature sensor.
![]() |
Engage the clip and 3 guides as shown in the illustration.
Install the console box insert with the 2 screws <C>.
| 7. INSTALL FRONT NO. 2 CONSOLE BOX INSERT |
for LHD:
Engage the 2 claws to connect the room temperature sensor.
![]() |
Engage the clip and 3 guides as shown in the illustration.
Install the front No. 2 console box insert with the 2 screws <C>.
| 8. INSTALL FRONT ASH RECEPTACLE ASSEMBLY |
Connect each connector.
![]() |
Engage the 2 clips.
Install the front ash receptacle assembly with the 2 screws <C>.
| 9. INSTALL FRONT CONSOLE UPPER PANEL GARNISH |
Connect each connector.
![]() |
Engage the 2 claws to install the front console upper panel garnish as shown in the illustration.
| 10. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Engage the 2 clips and 4 guides.
Install the 3 screws <C>.
Close the lower instrument panel door.
Install the lower instrument panel sub-assembly with the bolt <B> and screw <C>.
| 11. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
Connect the connector.
Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.
| 12. INSTALL INSTRUMENT SIDE PANEL RH |
![]() |
Engage the 3 guides as shown in the illustration.
![]() |
Engage the 4 claws to install the instrument side panel RH as shown in the illustration.
| 13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
| *1 | Alignment Mark (White) |
| 14. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH |
| 15. INSTALL FRONT DOOR SCUFF PLATE RH |
| 16. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY |
Connect each connector.
Engage the 5 clips and 3 guides.
Install the instrument panel sub-assembly with the 2 bolts <B>.
| 17. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
| 18. INSTALL INSTRUMENT SIDE PANEL LH |
![]() |
Engage the 3 guides.
![]() |
Engage the 4 claws to install the instrument side panel LH as shown in the illustration.
| 19. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| *1 | Alignment Mark (Yellow) |
| 20. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Insert the 2 clips in the direction indicated by the arrows shown in the illustration to engage them.
Install the cowl side trim sub-assembly LH with the clip.
| 21. INSTALL FRONT DOOR SCUFF PLATE LH |
Engage the 10 claws to install the front door scuff plate LH.
| 22. INSTALL CONSOLE BOX ASSEMBLY |
| 23. INSTALL SHIFT LOCK RELEASE BUTTON COVER (w/ Shift Lock Release Button Cover) |
![]() |
Engage the 2 claws to install the shift lock release button cover to the position indicator plate.
| *a | Groove |
| 24. INSPECT SHIFT LEVER POSITION |
While moving the shift lever from the N position to each position, check that the lever moves smoothly and that the shift position indicator comes on properly according to the shift lever position.
Put the vehicle into the READY-on state and check the following:
When the shift lever is moved to the D position, the vehicle moves forward.
When the shift lever is moved to the R position, the vehicle moves in reverse.