Home › Drivetrain › P314 HYBRID TRANSMISSION / TRANSAXLE › SHIFT LEVER

SHIFT LEVER > INSTALLATION

for Preparation Click here



1. INSTALL SHIFT LEVER SUPPORT


    C242187E01
  1. Install the shift lever support to the vehicle body with the 4 bolts in the sequence shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



2. INSTALL LOWER SHIFT LEVER ASSEMBLY

NOTICE:
Check that the shift lever position sensor and the shift lever are in neutral.



    C348793E01
  1. Install the lower shift lever assembly to the shift lever support with the 4 bolts in the sequence shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Connect the 3 clamps and connector.



    C194520E08
  1. Slide the slider of the transmission control cable assembly in the direction indicated by the arrow and pull the lock piece outward.
    Text in Illustration 
    *a
    Slider
    *b
    Lock Piece
    *c
    Slide
    *d
    Pull

  1. Engage the 2 claws to connect the transmission control cable assembly to the lower shift lever assembly.



    C348795E01
  1. Connect the end of the transmission control cable assembly to the shift lever assembly.
    Text in Illustration 
    *a
    Lock Piece

    NOTICE:
    1. Check that the lock piece is pulled up.
    2. Install the cable end all the way to the base of the pin.

  1. Push the lock piece into the adjuster case.

    NOTICE:
    1. Check that the shift lever position sensor and the shift lever are in neutral.
    2. Securely push in the lock piece until the slider lock is engaged.



3. INSTALL NO. 1 CONSOLE BOX DUCT
  1. Install the No. 1 console box duct to the lower shift lever assembly with the clip.



4. INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET
  1. Install the No. 1 console box mounting bracket to the lower shift lever assembly with the screw.



5. INSTALL FLOOR CARPET BRACKET LH
  1. Engage the 2 guides.

  1. Install the floor carpet bracket LH with the 2 clips.



6. INSTALL CONSOLE BOX INSERT
  1. for RHD:

    1. Engage the 2 claws to connect the room temperature sensor.



    B281779
  1. Engage the clip and 3 guides as shown in the illustration.

  1. Install the console box insert with the 2 screws <C>.



7. INSTALL FRONT NO. 2 CONSOLE BOX INSERT
  1. for LHD:

    1. Engage the 2 claws to connect the room temperature sensor.



    B281776
  1. Engage the clip and 3 guides as shown in the illustration.

  1. Install the front No. 2 console box insert with the 2 screws <C>.



8. INSTALL FRONT ASH RECEPTACLE ASSEMBLY
  1. Connect each connector.



    B384414
  1. Engage the 2 clips.

  1. Install the front ash receptacle assembly with the 2 screws <C>.



9. INSTALL FRONT CONSOLE UPPER PANEL GARNISH
  1. Connect each connector.



    B384415
  1. Engage the 2 claws to install the front console upper panel garnish as shown in the illustration.



10. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B281770
  1. Engage the 2 clips and 4 guides.

  1. Install the 3 screws <C>.

  1. Close the lower instrument panel door.

  1. Install the lower instrument panel sub-assembly with the bolt <B> and screw <C>.



11. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Connect the connector.

  1. Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.



12. INSTALL INSTRUMENT SIDE PANEL RH


    B281766
  1. Engage the 3 guides as shown in the illustration.



    B281764
  1. Engage the 4 claws to install the instrument side panel RH as shown in the illustration.



13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B278981E01
  1. Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
    Text in Illustration 
    *1
    Alignment Mark (White)

    NOTICE:
    After installation, check that the corners fit correctly.



14. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



15. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



16. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector.

  1. Engage the 5 clips and 3 guides.

  1. Install the instrument panel sub-assembly with the 2 bolts <B>.



17. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
  1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.



18. INSTALL INSTRUMENT SIDE PANEL LH


    B293646
  1. Engage the 3 guides.



    B280321
  1. Engage the 4 claws to install the instrument side panel LH as shown in the illustration.



19. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B278980E01
  1. Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *1
    Alignment Mark (Yellow)

    NOTICE:
    After installation, check that the corners fit correctly.



20. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B294701
  1. Insert the 2 clips in the direction indicated by the arrows shown in the illustration to engage them.

  1. Install the cowl side trim sub-assembly LH with the clip.



21. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Engage the 10 claws to install the front door scuff plate LH.



22. INSTALL CONSOLE BOX ASSEMBLY
(Click here)


23. INSTALL SHIFT LOCK RELEASE BUTTON COVER


    C348796E01
  1. Engage the 2 claws to install the shift lock release button cover to the shift position indicator.
    Text in Illustration 
    *a
    Groove

    NOTICE:
    Install the shift lock release button cover with its groove facing the left of the vehicle.



24. INSPECT SHIFT LEVER POSITION
  1. While moving the shift lever from N to each position, check that the lever moves smoothly and that the shift position indicator comes on properly according to the shift lever position.

  1. Put the vehicle into the READY-on state and check the following:

    1. When the shift lever is moved to D, the vehicle moves forward.

    2. When the shift lever is moved to R, the vehicle moves in reverse.

      NOTICE:
      The vehicle should not move when the shift position indicator is off.