SHIFT LEVER > REMOVAL |
| 1. REMOVE SHIFT LOCK RELEASE BUTTON COVER (w/ Shift Lock Release Button Cover) |
![]() |
Using a screwdriver as shown in the illustration, disengage the 2 claws to remove the shift lock release button cover from the position indicator plate.
| *a | Protective Tape |
| 2. REMOVE CONSOLE BOX ASSEMBLY |
| 3. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.
Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.
Disengage the 6 claws (C) to remove the front door scuff plate LH.
| 4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Remove the clip.
Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Disconnect the front door opening trim weatherstrip LH.
| 6. REMOVE INSTRUMENT SIDE PANEL LH |
![]() |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
| 7. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
| 8. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Remove the 2 bolts <B>.
![]() |
Disengage the 5 clips and 3 guides.
Disconnect each connector to remove the instrument panel sub-assembly
| 9. REMOVE FRONT DOOR SCUFF PLATE RH |
| 10. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
| 11. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Disconnect the front door opening trim weatherstrip RH.
| 12. REMOVE INSTRUMENT SIDE PANEL RH |
![]() |
Using moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.
| 13. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Disengage the 4 claws.
Disengage the 2 guides.
Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.
| 14. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Remove the bolt <B> and screw <C>.
Open the lower instrument panel door.
![]() |
Remove the 3 screws <C>.
![]() |
Disengage the 2 clips, 4 guides and remove the lower instrument panel sub-assembly as shown in the illustration.
| 15. REMOVE FRONT CONSOLE UPPER PANEL GARNISH |
![]() |
Disengage the 2 claws as shown in the illustration.
Disconnect each connector to remove the front console upper panel garnish.
| 16. REMOVE FRONT ASH RECEPTACLE ASSEMBLY |
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the 2 clips as shown in the illustration.
Disconnect each connector to remove the front ash receptacle assembly.
| 17. REMOVE FRONT NO. 2 CONSOLE BOX INSERT |
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the clip and 3 guides to remove the front No. 2 console box insert as shown in the illustration.
for LHD:
![]() |
Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.
| 18. REMOVE CONSOLE BOX INSERT |
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the clip and 3 guides to remove the console box insert as shown in the illustration.
for RHD:
![]() |
Disengage the 2 claws to disconnect the room temperature sensor from the console box insert.
| 19. REMOVE FLOOR CARPET BRACKET LH |
![]() |
Remove the 2 clips.
Disengage the 2 guides to remove the floor carpet bracket LH.
| 20. REMOVE NO. 1 CONSOLE BOX MOUNTING BRACKET |
![]() |
Remove the screw and No. 1 console box mounting bracket from the lower shift lever assembly.
| 21. REMOVE NO. 1 CONSOLE BOX DUCT |
![]() |
Remove the clip and No. 1 console box duct.
| 22. REMOVE LOWER SHIFT LEVER ASSEMBLY |
![]() |
Disconnect the end of transmission control cable assembly from the lower shift lever assembly.
Disengage the 2 claws and disconnect the transmission control cable assembly from the lower shift lever assembly.
![]() |
Disconnect the 3 clamps and connector.
![]() |
Remove the 4 bolts and lower shift lever assembly.
| 23. REMOVE SHIFT LEVER SUPPORT |
![]() |
Remove the 4 bolts and shift lever support.