Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

DTC    B1324    Lost Communication with Meter

for Preparation Click here


DESCRIPTION

This DTC is stored when a communication error occurs between the radio and display receiver assembly and combination meter assembly.

DTC No.
DTC Detection Condition
Trouble Area
B1324
After the radio and display receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the power switch is turned on (ACC), 1 or more times, the radio and display receiver assembly does not receive the signal for 30 seconds or more.
  1. Combination meter assembly
  2. Radio and display receiver assembly
  3. Harness or connector

WIRING DIAGRAM


E268494E14


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
  1. Disconnect the I185 radio and display receiver assembly connector.

  1. Disconnect the I18 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I185-3 (CNH1) - I18-18 (MSCH)
    Always
    Below 1 Ω
    I185-4 (CNL1) - I18-19 (MSCL)
    Always
    Below 1 Ω
    I185-3 (CNH1) - Body ground
    Always
    10 kΩ or higher
    I185-4 (CNL1) - Body ground
    Always
    10 kΩ or higher
    I185-3 (CNH1) - I185-4 (CNL1)
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I185-3 (CNH1) - Body ground
    Always
    Below 1 V
    I185-4 (CNL1) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT COMBINATION METER ASSEMBLY
  1. Remove the combination meter assembly (Click here).



    E286972E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    18 (MSCH) - 19 (MSCL)
    Always
    108 to 132 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Combination Meter Assembly)



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
  1. Remove the radio and display receiver assembly (Click here).



    E286972E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (CNH1) - 4 (CNL1)
    Always
    108 to 132 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


4.REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new or known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check that no DTCs are output.

    OK:
    No DTCs are output.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


5.CHECK METER / GAUGE SYSTEM
  1. Turn the power switch on (IG) and wait 30 seconds.

  1. Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter assembly and the audio system can be operated normally.

    OK:
    Audio system returns to normal.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END