HYBRID CONTROL SYSTEM > INFORMATION / FREEZE FRAME DATA |
| FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Hybrid Control / DTC.
Select a DTC in order to display its freeze frame data.
Check the freeze frame information recorded with the DTC.
| Tester Display | Measurement Item/Range | Suspected Vehicle Status When Malfunction Occurs |
| Engine Coolant Temp |
| Cold or warmed-up engine |
| Engine Revolution |
| Engine speed |
| Vehicle Spd |
| Stopped, or driving (at low, medium, or high speeds) |
| Engine Run Time |
| After the power switch is turned on (READY), elapsed time from initial engine start until the power switch is turned off. |
| +B |
| Auxiliary battery condition |
| Accel Pedal Pos #1 |
| Idling, accelerating, or decelerating |
| Accel Pedal Pos #2 |
| For comparison to accelerator pedal position sensor No. 1 |
| Ambient Temperature |
| Hot or cold weather |
| Intake Air Temperature |
| Hot or cold weather |
| DTC Clear Warm Up |
| Frequency of malfunction recurrence after clearing DTCs |
| DTC Clear Run Distance |
| Frequency of malfunction recurrence after clearing DTCs |
| DTC Clear Min |
| Elapsed time after clearing DTCs |
| MAP |
| - |
| Atmosphere Pressure |
| Vehicle driving elevation |
| Ready Signal |
| - |
| Motor(MG2) Revolution |
| - |
| Motor(MG2) Torq |
| - |
| M(MG2) Trq Exec Val |
| - |
| Generator(MG1) Rev |
| - |
| Generator(MG1) Torq |
| - |
| G(MG1) Trq Exec Val |
| - |
| Regenerative Brake Torq |
| - |
| Rqst Regen Brake Torq |
| - |
| Inverter Temp-(MG1) |
| - |
| Inverter Temp-(MG2) |
| - |
| Motor Temp No2 |
| - |
| Motor Temp No1 |
| - |
| Accelerator Degree |
| Idling, accelerating, or decelerating |
| Request Power |
| - |
| Target Engine Rev |
| - |
| Engine Rev (Sensor) |
| - |
| Total Distance Traveled |
| - |
| State of Charge (All Bat) |
| State of charge of HV battery |
| Master Cylinder Ctrl Trq |
| Brake force requested by driver |
| Power Resource VB |
| HV battery condition |
| Power Resource IB |
| HV battery condition |
| VL-Voltage before Boosting |
| - |
| VH-Voltage after Boosting |
| - |
| Boost Ratio |
| - |
| Drive Condition ID | Drive condition ID/
| Engine operating condition |
| Shift Sensor Shift Pos |
| Selected shift position |
| Crank Position |
| - |
| A/C Consumption Pwr |
| - |
| Short Wave Highest Val |
| Electrical leakage presence |
| MG1 Control Mode |
| Operating state of inverter with converter assembly |
| MG1 Carrier Frequency |
| Operating state of inverter with converter assembly |
| MG2 Control Mode |
| Operating state of inverter with converter assembly |
| MG2 Carrier Frequency |
| Operating state of inverter with converter assembly |
| Num of Current Code |
| - |
| Num of History Code |
| - |
| Shift Sensor SW - P |
| Shift lever position sensor |
| Shift Sensor SW - R |
| Shift lever position sensor |
| Shift Sensor SW - N |
| Shift lever position sensor |
| Shift Sensor SW - D |
| Shift lever position sensor |
| Shift Sensor SW - B |
| Shift lever position sensor |
| Shift Sensor SW - FD |
| Shift lever position sensor |
| Shift Sensor SW - RV |
| Shift lever position sensor |
| Shift Sensor SW - MJ |
| Shift lever position sensor |
| Calculate Load |
| - |
| Throttle Position |
| Idling, accelerating, or decelerating |
| DCDC Cnv Tar Pulse Duty |
| Auxiliary battery condition |
| Inverter Coolant Water Temperature |
| Hot or cold weather |
| Cooling Fan 0 |
| Cooling fan operating condition |
| Inverter W/P Revolution |
| Operating state of inverter water pump assembly |
| Prohibit DC/DC conv sig |
| Operating state of inverter with converter assembly |
| DC/DC Converter Status Voltage | DC/DC Converter Status Voltage Min.: 0.00 V, Max.: 4.99 V | - |
| EV Request |
| EV mode on or off |
| Primary DF Rqst on CCS | Status of the Primary DF Request on CCS / Pedal/None/Dsl | - |
| Operator Override | Status of the Operator Override / Notctrl/Able/Unable/Disable | - |
| Accelerator Info for DSS | Status of accelerator pedal ON or OFF | - |
| Gradient of Road Surface | Gradient of road surface Min.: -5.1 m/s2, Max.: 5.0 m/s2 | - |
| TRC OFF Switch |
| VSC OFF switch on or off |
| Permit Start by Immobiliser | Status of the Permit start by Immobiliser / Ini Cnd/No Chk/Check/Norml/Abnoml | - |
| Immobiliser Communication | Status of the Immobiliser Communication / OFF or ON | - |
| Starter Switch |
| - |
| Inv-T (MG1) aftr IG-ON |
| - |
| Inv-T (MG2) aftr IG-ON |
| - |
| Mtr-T (MG2) aftr IG-ON |
| - |
| Conv-Tmp after IG-ON |
| - |
| SOC after IG-ON |
| HV battery condition |
| Inv-Temp (MG1) Max |
| - |
| Inv-Temp (MG2) Max |
| - |
| Mtr-Temp (MG2) Max |
| - |
| Converter Temp Max |
| - |
| Status of Charge Max |
| HV battery condition |
| Status of Charge Min |
| HV battery condition |
| Stop Light Switch |
| Brake pedal depressed |
| Auxiliary Batt Temperature |
| - |
| Collision Signal (Airbag) |
| Operating state of airbag sensor assembly |
| TC Terminal |
| - |
| Inter Lock Switch |
| Power switch on (IG), connector cover assembly, upper inverter cover, No. 4 engine wire (air conditioner wire) or service plug grip not installed: ON |
| EV Switch |
| EV drive mode switch (pattern select switch assembly) on or off |
| Back Up Lamp Relay |
| Shift lever in R: ON |
| ECO Mode |
| ECO mode on or off |
| Generate Torque |
| - |
| Prohibit Charge for P Pos |
| - |
| DC/DC Cnv Temp (Upper) |
| - |
| Safing Signal (Airbag) |
| Operating state of airbag sensor assembly |
| DC/DC Cnv Temp (Lower) |
| - |
| Normal Signal for A/B ECU |
| Operating state of airbag sensor assembly |
| Mtr-T (MG1) aftr IG-ON |
| - |
| Mtr-Temp (MG1) Max |
| - |
| Overvoltage Input to Conv |
| - |
| Overvoltage Input to Inv |
| - |
| Emergency Shutdown |
| Operating state of inverter with converter assembly |
| MG1 Inverter Shutdown |
| Operating state of inverter with converter assembly |
| MG1 Inverter Fail |
| Operating state of inverter with converter assembly |
| MG2 Inverter Shutdown |
| Operating state of inverter with converter assembly |
| MG2 Inverter Fail |
| Operating state of inverter with converter assembly |
| Conv Shutdown |
| Operating state of inverter with converter assembly |
| Converter Fail |
| Operating state of inverter with converter assembly |
| Internal Shift Position |
| Selected shift position |
| HV Start Condition |
| - |
| (Inverter) W/P Run Control Duty |
| Operating state of inverter water pump assembly |
| Engine Stop Request |
| Engine operating conditions |
| Engine Idling Request |
| Engine operating conditions |
| Main Batt Charging Rqst |
| HV battery condition |
| Aircon Request |
| - |
| Engine Warming Up Rqst |
| Engine operating conditions |
| SMRP Status |
| Cannot be confirmed using the intelligent tester. Use an oscilloscope. |
| SMRB Status |
| - |
| SMRG Status |
| - |
| SMRP Control Status |
| Cannot be confirmed using the intelligent tester. Use an oscilloscope. |
| SMRB Control Status |
| - |
| SMRG Control Status |
| - |
| MG1 Gate Status |
| Operating state of inverter with converter assembly |
| MG2 Gate Status |
| Operating state of inverter with converter assembly |
| Converter Gate Status |
| Operating state of inverter with converter assembly |
| Aircon Gate Status |
| Operating state of inverter with converter assembly |
| Converter Carrier Freq |
| Operating state of inverter with converter assembly |
| Delta SOC |
| SOC variance |
| Batt Pack Current Val |
| HV battery charge/discharge status
|
| Inhaling Air Temp |
| - |
| Auxiliary Battery Vol |
| Auxiliary battery condition |
| Charge Control Value |
| Charge amount of HV battery |
| Discharge Control Value |
| Discharge amount of HV battery |
| Cooling Fan Mode1 |
| HV battery cooling fan activation condition
|
| Cooling Fan Frequency |
| Battery cooling blower assembly |
| ECU Control Mode |
| HV battery control status |
| Standby Blower Request |
| Operating state of cooling fan |
| Temp of Batt TB1 |
| HV battery temperature |
| Temp of Batt TB2 |
| HV battery temperature |
| Temp of Batt TB3 |
| HV battery temperature |
| Battery Block Vol -V01 |
| Each HV battery block voltage variance |
| Battery Block Vol -V02 |
| Each HV battery block voltage variance |
| Battery Block Vol -V03 |
| Each HV battery block voltage variance |
| Battery Block Vol -V04 |
| Each HV battery block voltage variance |
| Battery Block Vol -V05 |
| Each HV battery block voltage variance |
| Battery Block Vol -V06 |
| Each HV battery block voltage variance |
| Battery Block Vol -V07 |
| Each HV battery block voltage variance |
| Battery Block Vol -V08 |
| Each HV battery block voltage variance |
| Battery Block Vol -V09 |
| Each HV battery block voltage variance |
| Battery Block Vol -V10 |
| Each HV battery block voltage variance |
| Battery Block Vol -V11 |
| Each HV battery block voltage variance |
| Battery Block Vol -V12 |
| Each HV battery block voltage variance |
| Battery Block Vol -V13 |
| Each HV battery block voltage variance |
| Battery Block Vol -V14 |
| Each HV battery block voltage variance |
| Battery Block Vol -V15 |
| Each HV battery block voltage variance |
| Battery Block Vol -V16 |
| Each HV battery block voltage variance |
| Battery Block Vol -V17 |
| Each HV battery block voltage variance |
| Detail Code 1 |
| - |
| Detail Code 2 |
| - |
| Detail Code 3 |
| - |
| Detail Code 4 |
| - |
| Detail Code 5 |
| - |
| INFORMATION |
Select the information item which has an INF code from among INFORMATION 1 to 5.
Check the information for the DTC.
| Tester Display | Measurement Item/Range | Suspected Vehicle Status When Malfunction Occurs |
| Information 1 to 5 | INF code | Identification of malfunctioning system |
| Generator(MG1) Rev |
| MG1 speed
|
| Motor(MG2) Revolution |
| MG2 speed
|
| Generator(MG1) Torq |
| When MG1 rotates in "+" direction:
|
| Motor(MG2) Torq |
| When MG2 rotates in "+" direction:
|
| Request Power |
| Engine power output requested to ECM |
| Engine Spd |
| Engine speed |
| Master Cylinder Ctrl Trq |
| Brake force requested by driver |
| State of Charge |
| Charge of amount HV battery |
| WOUT Control Power |
| Discharge amount of HV battery |
| WIN Control Power |
| Charge amount of HV battery |
| Drive Condition ID | Drive condition ID/
| Engine operating condition |
| Power Resource VB |
| HV battery voltage |
| Power Resource IB |
| HV battery charge and discharge current
|
| Shift Sensor Shift Pos |
| Shift lever position sensor |
| Auxiliary Batt Voltage |
| Auxiliary battery condition |
| VL-Voltage before Boosting |
| High voltage level before it is boosted |
| VH-Voltage after Boosting |
| High voltage level after it is boosted |
| The Time of Ignition ON |
| Time elapsed with power switch on (IG) |
| Vehicle Speed(Max) |
| Maximum vehicle speed |
| Engine Stop Request |
| Engine stop request |
| Engine Idling Request |
| Idle stop request |
| Engine Fuel Cut |
| Fuel cut |
| Main Batt Charging Rqst |
| HV battery charging request |
| Engine Warming Up Rqst |
| Engine warm-up request |
| Stop Switch |
| Brake pedal depressed or released |
| Exclusive Information 1 |
| Exclusive information linked to Information |
| Exclusive Information 2 |
| Exclusive information linked to Information |
| Exclusive Information 3 |
| Exclusive information linked to Information |
| Exclusive Information 4 |
| Exclusive information linked to Information |
| Exclusive Information 5 |
| Exclusive information linked to Information |
| Exclusive Information 6 |
| Exclusive information linked to Information |
| Exclusive Information 7 |
| Exclusive information linked to Information |
| Occurrence Order | Occurrence sequence of information | Occurrence sequence of information |
| Cnv Tmp (Upper) |
| Boost converter temperature |
| Cnv Temp (Lower) |
| Boost converter temperature |
| Generator Temp |
| MG1 temperature |
| MG1 Carrier Frequency |
| MG1 inverter carrier frequency |
| MG2 Carrier Frequency |
| MG2 inverter carrier frequency |
| Motor Temp |
| MG2 carrier temperature |
| Converter Carrier Freq |
| Converter carrier frequency |
| Inverter Temp (MG1) |
| Generator inverter temperature |
| MG1 Control Mode |
| MG1 control mode |
| Inverter Temp (MG2) |
| Motor inverter temperature |
| MG2 Control Mode |
| MG2 control mode |
| Boost Ratio |
| Boost condition |
| MG1 Inverter Shutdown |
| Generator inverter shutdown: ON |
| HV Coolant Temperature |
| HV coolant temperature |
| MG2 Inverter Shutdown |
| Motor inverter shutdown: ON |
| Accel Sensor Main |
| Idling, accelerating, or decelerating |
| Conv Shutdown |
| Boost converter shutdown: ON |