WHEN REMOVING,INSTALLING OR REPLACING PARTS > WHEEL ALIGNMENT STANDARD



MEASURE VEHICLE HEIGHT (for TMMK Made)
C239047E01

NOTICE:
  1. Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
  2. Be sure to perform measurement on a level surface.
  3. If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
  4. Inspect while the vehicle is unloaded.
  5. The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  2. Measure the vehicle height.

    Measurement points:
    1. A: Ground clearance of front wheel center
    2. B: Ground clearance of No. 2 lower suspension arm bushing set bolt center
    3. C: Ground clearance of rear wheel center
    4. D: Ground clearance of strut rod set bolt center

    Vehicle Height (Unloaded Vehicle) 
    Front A - B
    Rear C - D
    125 mm (4.92 in.)
    55 mm (2.17 in.)


MEASURE VEHICLE HEIGHT (for TMC, TMMR Made)
C239047E01

NOTICE:
  1. Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
  2. Be sure to perform measurement on a level surface.
  3. If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
  4. Inspect while the vehicle is unloaded.
  5. The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  2. Measure the vehicle height.

    Measurement points:
    1. A: Ground clearance of front wheel center
    2. B: Ground clearance of No. 2 lower suspension arm bushing set bolt center
    3. C: Ground clearance of rear wheel center
    4. D: Ground clearance of strut rod set bolt center

    Vehicle Height (Unloaded Vehicle) 
    Tire Size
    Front A - B
    Rear C - D
    215/60R16
    112 mm (4.41 in.)
    112 mm (4.41 in.)*1
    114 mm (4.49 in.)*3
    40 mm (1.57 in.)
    41 mm (1.61 in.)*1
    40 mm (1.57 in.)*3
    215/55R17
    116 mm (4.57 in.)
    113 mm (4.45 in.)*1
    117 mm (4.61 in.)*2
    46 mm (1.81 in.)
    42 mm (1.65 in.)*1
    47 mm (1.85 in.)*2
    1. *1: for Russia 2AR-FE
    2. *2: for Russia 2GR-FE
    3. *3: for Russia 6AR-FSE


INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION (for TMMK Made)

NOTICE:
Inspect while the vehicle is unloaded.



    C132440E21
  1. Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.
    Text in Illustration 
    *1
    Turning Radius Gauge
    *2
    Camber-caster-kingpin Gauge

  2. Inspect the camber, caster and steering axis inclination.

    Camber (Unloaded Vehicle) 
    Camber Inclination
    Right-left Difference
    -0°42' +/- 45' (-0.70° +/- 0.75°)
    45' (0.75°) or less

    Caster (Unloaded Vehicle) 
    Caster Inclination
    Right-left Difference
    2°58' +/- 45' (2.97° +/- 0.75°)
    45' (0.75°) or less

    Steering Axis (Unloaded Vehicle) 
    Steering Axis Inclination Reference
    12°16' (12.27°)

    1. * For Russia


INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION (for TMC, TMMR Made)

NOTICE:
Inspect while the vehicle is unloaded.



    C132440E21
  1. Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.
    Text in Illustration 
    *1
    Turning Radius Gauge
    *2
    Camber-caster-kingpin Gauge

  2. Inspect the camber, caster and steering axis inclination.

    Camber (Unloaded Vehicle) 
    Tire Size
    Camber Inclination
    Right-left Difference
    215/60R16
    -0°35' +/- 45' (-0.58° +/- 0.75°)
    45' (0.75°) or less
    215/55R17
    -0°35' +/- 45' (-0.58° +/- 0.75°)

    Caster (Unloaded Vehicle) 
    Tire Size
    Caster Inclination
    Right-left Difference
    215/60R16
    2°45' +/- 45' (2.75° +/- 0.75°)
    2°50' +/- 45' (2.83° +/- 0.75°)*1
    2°45' +/- 45' (2.75° +/- 0.75°)*2
    45' (0.75°) or less
    215/55R17
    2°50' +/- 45' (2.83° +/- 0.75°)

    1. *1: for Russia 2AR-FE
    2. *2: for Russia 6AR-FSE

    Steering Axis (Unloaded Vehicle) 
    Tire Size
    Steering Axis Inclination Reference
    215/60R16
    11°55' (11.92°)
    12°00' (12.00°)*1
    215/55R17
    12°05' (12.08°)
    12°00' (12.00°)*2
    12°05' (12.08°)*3
    1. *1: for Russia
    2. *2: for Russia 2AR-FE
    3. *3: for Russia 2GR-FE


INSPECT TOE-IN (FRONT) (for TMMK Made)

NOTICE:
Inspect while the vehicle is unloaded.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  2. Release the parking brake and move the shift lever to N.

  3. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)



  4. C188968E05
  5. Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
    Text in Illustration 
    *a
    Tread Center Mark
    *b
    Dimension B
    V100135
    Front of the Vehicle

  6. Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

    HINT:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step C again.



  7. C188969E05
  8. Measure the distance between the tread center marks on the front of the wheels (dimension A).
    Text in Illustration 
    *a
    Dimension A
    V100135
    Front of the Vehicle
    Toe-in (Unloaded Vehicle) 
    Specified Condition
    C + D: 0°00' +/- 0°10' (0.00° +/- 0.17°)
    B - A: 0 +/- 2.0 mm (0 +/- 0.0787 in.)

    HINT:
    Measure "B - A" only when "C + D" cannot be measured.
    If the toe-in is not within the specified range, adjust it at the rack ends.


INSPECT TOE-IN (FRONT) (for TMC, TMMR Made)

NOTICE:
Inspect while the vehicle is unloaded.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  2. Release the parking brake and move the shift lever to N.

  3. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)



  4. C188968E05
  5. Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
    Text in Illustration 
    *a
    Tread Center Mark
    *b
    Dimension B
    V100135
    Front of the Vehicle

  6. Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

    HINT:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step C again.



  7. C188969E05
  8. Measure the distance between the tread center marks on the front of the wheels (dimension A).
    Text in Illustration 
    *a
    Dimension A
    V100135
    Front of the Vehicle
    Toe-in (Unloaded Vehicle) 
    Specified Condition
    C + D: 0°00' +/- 0°11' (0.00° +/- 0.18°)
    B - A: 0 +/- 2.0 mm (0 +/- 0.0787 in.)

    HINT:
    Measure "B - A" only when "C + D" cannot be measured.
    If the toe-in is not within the specified range, adjust it at the rack ends.


INSPECT WHEEL ANGLE (for TMMK Made)
C132439E11
  1. Put tread center marks on the rearmost points of a turning radius gauge.
    Text in Illustration 
    *a
    Inside
    *b
    Outside
    V100135
    Front of the Vehicle

  2. Turn the steering wheel fully to the left and right and measure the turning angle.

    NOTICE:
    Inspect while the vehicle is unloaded.


    Wheel Turning Angle (Unloaded Vehicle) 
    Inside Wheel
    Outside Wheel
    37°13' +/- 2° (37.22° +/- 2°)
    32°49' +/- 2° (32.81° +/- 2°)
    1. If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.


INSPECT WHEEL ANGLE (for TMC, TMMR Made)
C132439E11
  1. Put tread center marks on the rearmost points of a turning radius gauge.
    Text in Illustration 
    *a
    Inside
    *b
    Outside
    V100135
    Front of the Vehicle

  2. Turn the steering wheel fully to the left and right and measure the turning angle.

    NOTICE:
    Inspect while the vehicle is unloaded.


    Wheel Turning Angle (Unloaded Vehicle) 
    Tire Size
    Inside Wheel
    Outside Wheel
    215/60R16
    39°58' +/- 2° (39.97° +/- 2°)
    38°57' +/- 2° (38.95° +/- 2°)*1
    38°52' +/- 2° (38.87° +/- 2°)*3
    33°59' (33.98°)
    33°59' (33.98°)*1
    33°56' (33.93°)*3
    215/55R17
    38°50' +/- 2° (38.83° +/- 2°)
    38°55' +/- 2° (38.92° +/- 2°)*1
    38°49' +/- 2° (38.82° +/- 2°)*2
    33°54' (33.90°)
    33°58' (33.97°)*1
    33°53' (33.88°)*2
    1. *1: for Russia 2AR-FE
    2. *2: for Russia 2GR-FE
    3. *3: for Russia 6AR-FSE
    4. If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.


INSPECT CAMBER (REAR) (for TMMK Made)

NOTICE:
Inspect while the vehicle is unloaded.



    C107736E10
  1. Install a camber-caster-kingpin gauge.
    Text in Illustration 
    *a
    Camber-caster-kingpin Gauge

  2. Inspect the camber.

    Camber (Unloaded Vehicle) 
    Camber Inclination
    Right-left Difference
    -1°15' +/- 45' (-1.25° +/- 0.75°)
    45' (0.75°) or less

    HINT:
    Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.


INSPECT CAMBER (REAR) (for TMC, TMMR Made)

NOTICE:
Inspect while the vehicle is unloaded.



    C107736E10
  1. Install a camber-caster-kingpin gauge.
    Text in Illustration 
    *a
    Camber-caster-kingpin Gauge

  2. Inspect the camber.

    Camber (Unloaded Vehicle) 
    Tire Size
    Camber Inclination
    Right-left Difference
    215/60R16
    -1°08' +/- 45' (-1.13° +/- 0.75°)
    -1°09' +/- 45' (-1.15° +/- 0.75°)*1
    -1°07' +/- 45' (-1.12° +/- 0.75°)*3
    45' (0.75°) or less
    215/55R17
    -1°11' +/- 45' (-1.18° +/- 0.75°)
    -1°09' +/- 45' (-1.15° +/- 0.75°)*1
    -1°12' +/- 45' (-1.20° +/- 0.75°)*2

    1. *1: for Russia 2AR-FE
    2. *2: for Russia 2GR-FE
    3. *3: for Russia 6AR-FSE

    HINT:
    Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.


INSPECT TOE-IN (REAR) (for TMMK Made)

NOTICE:
Inspect while the vehicle is unloaded.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  2. Release the parking brake and move the shift lever to N.

  3. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)



  4. C188968E06
  5. Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).
    Text in Illustration 
    *a
    Tread Center Mark
    *b
    Dimension B
    V100135
    Front of the Vehicle

  6. Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

    HINT:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step A again.



  7. C188969E06
  8. Measure the distance between the tread center marks on the front of the rear wheels (dimension A).
    Text in Illustration 
    *a
    Dimension A
    V100135
    Front of the Vehicle

    Toe-in (Unloaded Vehicle) 
    Specified Condition
    C + D: 0°13' +/- 0°10' (0.21° +/- 0.17°)
    B - A: 2.5 +/- 2.0 mm (0.0984 +/- 0.0787 in.)

    HINT:
    Measure "B - A" only when "C + D" cannot be measured.
    If the toe-in is not within the specified range, adjust it at the rear No. 2 suspension arms.


INSPECT TOE-IN (REAR) (for TMC, TMMR Made)

NOTICE:
Inspect while the vehicle is unloaded.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  2. Release the parking brake and move the shift lever to N.

  3. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)



  4. C188968E06
  5. Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).
    Text in Illustration 
    *a
    Tread Center Mark
    *b
    Dimension B
    V100135
    Front of the Vehicle

  6. Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

    HINT:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step A again.



  7. C188969E06
  8. Measure the distance between the tread center marks on the front of the rear wheels (dimension A).
    Text in Illustration 
    *a
    Dimension A
    V100135
    Front of the Vehicle

    Toe-in (Unloaded Vehicle) 
    Specified Condition
    C + D: 0°22' +/- 0°11' (0.37° +/- 0.18°)
    B - A: 4.0 +/- 2.0 mm (0.157 +/- 0.0787 in.)

    HINT:
    Measure "B - A" only when "C + D" cannot be measured.
    If the toe-in is not within the specified range, adjust it at the rear No. 2 suspension arms.