TOYOTA PARKING ASSIST-SENSOR SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS

Component
Function
Clearance Warning ECU Assembly
  1. Judges the approximate distance between the vehicle and an obstacle based on signals from the No. 1 ultrasonic sensors. Output signals are sent to the multi-information display.
  2. Sounds the No. 1 clearance warning buzzer.
No. 1 Ultrasonic Sensor (6)
Detects the distance between an vehicle and the obstacle.
No. 1 Clearance Warning Buzzer
Sounds to inform the driver according to the distance to the obstacle.
Combination Meter Assembly
- Multi-information Display
  1. Displays the location of the obstacle and the approximate distance between the vehicle and the obstacle.
  2. Displays an indication of a malfunction or freezing of a No. 1 ultrasonic sensor to inform the driver.
Back Sonar or Clearance Sonar Switch Assembly
Operating this switch allows the operation of the TOYOTA parking assist-sensor system to be enabled or disabled.
Radio and Display Receiver Assembly*
  1. Displays the location of an obstacle and the approximate distance between the vehicle and the obstacle.
  2. Displays an indication of a malfunction or freezing of a No. 1 ultrasonic sensor to inform the driver.
Air Conditioning Amplifier Assembly
Sends outside temperature information to the clearance warning ECU assembly to adjust the distance rate from the No. 1 ultrasonic sensors.
Main Body ECU (Multiplex Network Body ECU)
Sends model destination (information to indicate the market the vehicle was built for) to the clearance warning ECU assembly.
Park/Neutral Position Switch Assembly
Sends the shift position signals to the ECM.
ECM
Transmits the shift position signals to the clearance warning ECU assembly.
  1. *: Models with parking assist monitor system

OPERATING CONDITION
  1. The operating condition of each sensor differs according to its installed position as shown in the table below:

    Installation Position
    Operating Condition
    Front Corner
    1. Ignition switch is ON.
    2. System is activated.
    3. Shift lever is in a position other than P or R.
    4. Vehicle speed is approximately 10 km/h (6 mph) or less.
    1. Ignition switch is ON.
    2. System is activated.
    3. Shift lever is in R.
    Rear Corner
    1. Ignition switch is ON.
    2. System is activated.
    3. Shift lever is in R.
    Rear Center
    1. Ignition switch is ON.
    2. System is activated.
    3. Shift lever is in R.


CONSTRUCTION


  1. No. 1 Ultrasonic Sensor

    1. The No. 1 ultrasonic sensors consist of a microphone and a circuit portion that transmits and receives ultrasonic waves.



    2. The circuit portion is filled with urethane to prevent water from entering.


      Y111325E01


      Text in Illustration 
      *1
      Circuit Portion
      *2
      Microphone
      *a
      A-A Cross Section
      -
      -


OPERATION


  1. No. 1 Clearance Warning Buzzer

    1. Depending on the detection distance and the detection area, the sound pattern of the No. 1 clearance warning buzzer will vary.

      Detection Area
      Detection Distance
      (mm (in.))
      Buzzer Sound Pattern
      On
      (msec.)
      Off
      (msec.)
      Front Corner
      Long
      500 +/- 50 to 400 +/- 40 (19.7 +/- 2.0 to 15.7 +/- 1.6)
      150 +/- 15
      150 +/- 15
      Middle
      400 +/- 40 to 300 +/- 30 (15.7 +/- 1.6 to 11.8 +/- 1.2)
      75 +/- 7.5
      75 +/- 7.5
      Short
      300 +/- 30 or less (11.8 +/- 1.2 or less)
      Continuous Sound
      0
      Rear Corner
      Long
      600 +/- 60 to 450 +/- 50 (23.6 +/- 2.4 to 17.7 +/- 2.0)
      150 +/- 15
      150 +/- 15
      Middle
      450 +/- 50 to 300 +/- 30 (17.7 +/- 2.0 to 11.8 +/- 1.2)
      75 +/- 7.5
      75 +/- 7.5
      Short
      300 +/- 30 or less (11.8 +/- 1.2 or less)
      Continuous Sound
      0
      Rear Center
      Longest
      1500 +/- 150 to 600 +/- 60 (59.1 +/- 5.9 to 23.6 +/- 2.4)
      150 +/- 1.5
      650 +/- 65
      Long
      600 +/- 60 to 450 +/- 50 (23.6 +/- 2.4 to 17.7 +/- 2.0)
      150 +/- 1.5
      150 +/- 1.5
      Middle
      450 +/- 50 to 350 +/- 40 (17.7 +/- 2.0 to 13.8 +/- 1.6)
      75 +/- 7.5
      75 +/- 7.5
      Short
      350 +/- 40 or less (13.8 +/- 1.6 or less)
      Continuous Sound
      0



    2. The No. 1 ultrasonic sensors are divided into 2 groups: a front section group (front corners) and a rear section group (rear corners and rear center). If multiple No. 1 ultrasonic sensors detect obstructions at the same time, the No. 1 clearance warning buzzer sounds as follows, in accordance with the detection distance and detection area of each group:

      Buzzer Sound Pattern ON/OFF Time (msec.) 
      Detection Distance
      Short (*A)
      Middle (*A)
      Long (*A)
      Not detected
      Short (*B)
      Timing 1
      Timing 2
      Timing 2
      Continuous Sound
      Middle (*B)
      Timing 2
      75/75
      75/75
      75/75
      Long (*B)
      Timing 2
      75/75
      150/150
      150/150
      Longest (*B)
      Timing 2
      75/75
      150/150
      150/650
      Not detected
      Continuous Sound
      75/75
      150/150
      None

      1. *A: Front section
      2. *B: Rear section

      Y102524E04



  2. Multi-information Display

    1. The location of an obstacle and the approximate distance between the vehicle and the obstacle are displayed on the multi-information display.



    2. The number of lines shown on the display changes based on the actual distance and flashes when the distance is short.


      Y169219E01


      Text in Illustration 
      *1
      Front Corner LH
      *2
      Front Corner RH
      *3
      Rear Corner LH
      *4
      Rear Corner RH
      *5
      Rear Center
      *6
      Distance
      *7
      Longest
      *8
      Long
      *9
      Middle
      *10
      Short
      *11
      Flashes
      -
      -



    3. Screens displaying warning messages relating to a No. 1 ultrasonic sensor malfunction, No. 1 ultrasonic sensor freezing, or presence of foreign matter on the No. 1 ultrasonic sensor, are displayed on the multi-information display.


      Y169220E01


      Text in Illustration 
      *1
      Malfunctioning
      *2
      Frozen/Dirty



  3. Multi-display (Models with Parking Assist Monitor System)

    1. If an obstacle is detected when the parking assist monitor system is activated, the approximate distance between the vehicle and the obstacle is displayed on the multi-display.



    2. The distance is displayed by color based on the actual distance to the obstacle. When an obstacle is detected at the long or middle distance, the indicator is yellow. The color changes from yellow to red when the distance becomes short.


      Y170712E01


      Text in Illustration 
      *1
      Front Corner LH
      *2
      Front Corner RH
      *3
      Rear Corner LH
      *4
      Rear Corner RH
      *5
      Rear Center
      -
      -
      *a
      The illustrations shown are examples only. The illustrations may differ from the actual vehicle screens.
      -
      -



    3. The following items displayed by the multi-display are warning relating to sensor malfunction, sensor freezing, or presence of dirt on the sensor.


      Y169222E01


      Text in Illustration 
      *1
      Malfunctioning
      *2
      Frozen/Dirty



  4. Detection Area

    1. The detection areas of the No. 1 ultrasonic sensor are as shown in the following illustration.



    2. These detection areas are applicable when positioning a 60 mm (2.36 in.) diameter pole parallel or perpendicular to the ground. The ranges vary depending on the measuring method and type of obstacle.


      Y170682E01


      Text in Illustration (Corner Area:) 
      *a
      Approximately 700 mm (27.6 in.)
      *b
      Approximately 750 mm (29.5 in.)
      *c
      Approximately 500 mm (19.7 in.)
      *d
      Approximately 600 mm (23.6 in.)
      *e
      Approximately 400 mm (15.7 in.)
      *f
      Approximately 200 mm (7.9 in.)

      Y170683E01


      Text in Illustration (Rear Center Area:) 
      *a
      Approximately 1800 mm (70.9 in.)
      *b
      Approximately 200 mm (7.9 in.)
      *c
      Approximately 1000 mm (39.4 in.)
      *d
      Approximately 500 mm (19.7 in.)


DIAGNOSIS
  1. If a system malfunction is detected, the clearance warning ECU assembly stores Diagnostic Trouble Codes (DTCs) in its memory. For details, refer to the Repair Manual.