AIR CONDITIONING SYSTEM > GENERAL



OUTLINE
  1. The automatic air conditioning system uses left and right independent temperature control and neural network control to enhance comfort.


MAJOR DIFFERENCE
  1. The new models have been modified from the previous models as shown below:

    1. TMMK Made Models have been added.

    2. The 6AR-FSE engine specifications have been added.


SPECIFICATION
  1. Performance

    Heater
    Heater Output
    W
    5850
    Air Flow Volume
    m3/h
    380
    Power Consumption
    W
    220
    Cooler
    Cooling Capacity
    W
    6100
    Air Flow Volume
    m3/h
    530
    Power Consumption
    W
    260

  2. Ventilation and Heater Core

    Heater Radiator Unit Sub-assembly
    Type
    Straight Flow Aluminum (SFA) -II
    Size W x H x L
    mm (in.)
    201.5 x 150 x 27 (7.9 x 5.9 x 1.1)
    Fin Pitch
    mm (in.)
    1.5 (0.06)
    Blower with Fan Motor Sub-assembly
    Motor Type
    BMM - K70
    Fan Type
    Semi Sirocco
    Fan Size (Dia. x H)
    mm (in.)
    165 x 70 (6.5 x 2.8)

  3. Air Conditioning

    Cooler Condenser Assembly
    Type
    Multi-Flow (MF)-IV
    Size W x H x L
    mm (in.)
    720 x 370.2 x 16
    (28.3 x 14.6 x 0.6)
    Fin Pitch
    mm (in.)
    3.15 (0.12)
    Compressor
    (Compressor with Pulley Assembly*1)
    (Cooler Compressor Assembly*2)
    Type
    TSE17C*1
    TSB17C*2
    Pulley
    Plastic Damper and Limiter (DL)*1
    Steel with Magnetic Clutch*2
    Oil Volume
    cc
    100 to 115
    Refrigerant
    Type
    HFC 134a
    Charge Volume
    g
    450 to 550
    Evaporator
    Type
    Revolutionary super-slim Structure (RS)
    Size W x H x L
    mm (in.)
    266.3 x 251 x 38 (10.5 x 9.9 x 1.5)
    Fin Pitch
    mm (in.)
    2.6 (0.10)
    *1: Models with 2AR-FE engine or 6AR-FSE engine
    *2: Models with 2GR-FE engine


MAIN FEATURES
  1. The air conditioning system has the following features:

    High Performance
    1. Using the following features of the compressor (continuously variable capacity compressor), high cooling performance and a quiet cabin have been achieved:
      1. Neural network control is used so passengers can finely control the air conditioning for maximum comfort.
      2. The blower control has 7 steps to allow precise control.
      3. Magnetic Flux Sensor Type Air Conditioning Mass Flow Sensor
      4. Oil Separator
      5. Variable Suction Side Throttle
      6. Solenoid Valve with Built-in Crank Chamber to Suction Passage (CS) Valve
    Lightweight
    1. An air conditioning harness assembly with a built-in IC is used in a lightweight wire harness design to allow a reduced number of wires.
    2. The use of this connector means that pulse pattern type servo motors are used.
    Others
    The following parts are used to ensure high cooling performance while realizing a compact and lightweight construction.
    1. Semi-center Location Air Conditioning Unit
    2. Revolutionary Super-slim Structure (RS) Evaporator
    3. Straight Flow Aluminum (SFA)-II Heater Radiator Sub-assembly
    4. Multi-Flow (MF)-IV Sub-cool Condenser