Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY (for TMMK Made)

PARKING BRAKE ASSEMBLY (for TMMK Made) > REASSEMBLY

for Preparation Click here



1. APPLY HIGH TEMPERATURE GREASE


    C237828
  1. Apply high temperature grease to the areas of the parking brake plate which make contact with the shoe as shown in the illustration.
    Text in Illustration 
    V100155
    High Temperature Grease



2. INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN
  1. Install the 2 parking brake shoe hold down spring pins.



3. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)
  1. Install the parking brake shoe return tension spring to the No. 2 parking brake shoe assembly.



4. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY
  1. Install the No. 1 parking brake shoe assembly to the parking brake shoe return tension spring.



5. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET


    C236276
  1. Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.
    Text in Illustration 
    V100155
    High Temperature Grease

  1. Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly.



6. INSTALL PARKING BRAKE SHOE LEVER


    C239416
  1. Using needle-nose pliers, install the parking brake shoe lever to the No. 3 parking brake cable assembly.



    C237829
  1. Apply high temperature grease to the areas of the parking brake shoe lever which make contact with the No. 2 parking brake shoe assembly.
    Text in Illustration 
    V100155
    High Temperature Grease



    C239417
  1. Install the parking brake shoe lever to the No. 2 parking brake shoe assembly.

  1. Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and fit them to the parking brake plate.

    NOTICE:
    Make sure that the parking brake shoe lever does not separate from the No. 2 parking brake shoe assembly.



7. INSTALL PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Rear Side)


    C237820E01
  1. Using SST, install the parking brake shoe hold down compression spring.

    SST
    09718-00011  



8. INSTALL PARKING BRAKE SHOE STRUT
  1. Install the parking brake shoe strut.



    C239418
  1. Install the No. 1 parking brake shoe assembly.



9. INSTALL PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Front Side)


    C237817E01
  1. Using SST, install the parking brake shoe hold down compression spring.

    SST
    09718-00011  



10. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Rear Side)


    C239404
  1. Apply a small amount of high temperature grease to the areas shown in the illustration.
    Text in Illustration 
    V100155
    High Temperature Grease

  1. Install the parking brake shoe return tension spring.



11. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Front Side)
  1. Install the parking brake shoe return tension spring.



12. CHECK PARKING BRAKE INSTALLATION


  1. Check that each part is installed properly.


    C237830E01


    Text in Illustration 
    *A
    LH Side
    *B
    RH Side
    V100135
    Front of the Vehicle
    -
    -

    NOTICE:
    There should be no oil or grease on the friction surfaces of the shoe linings or discs.



13. INSTALL REAR DISC


    C238505E01
  1. Align the matchmarks of the rear disc and rear axle hub, and install the rear disc.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.



14. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG


15. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
  1. Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    78 N*m{ 799 kgf*cm , 58 ft.*lbf }

  1. Install the rear flexible hose to the rear shock absorber assembly with the bolt.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }



16. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL
  1. Completely release the parking brake pedal.



  1. for TMC, TMMR Made:



      C237831E01
    1. Loosen the lock nut and the adjusting nut to completely release the parking brake cable.
      Text in Illustration 
      *1
      Lock Nut
      *2
      Adjusting Nut



  1. for TMMK Made:



      C237831E01
    1. Remove the lock nut and loosen the adjusting nut to completely release the parking brake cable.
      Text in Illustration 
      *1
      Lock Nut
      *2
      Adjusting Nut

      NOTICE:
      If the lock nut is removed or loosened, replace the lock nut with a new one.

  1. Remove the rear wheels.

  1. Temporarily install the hub nuts to the hub bolts.

    HINT:
    Securely install the hub nuts to the rear disc.

  1. Remove the parking brake shoe adjusting hole plug.



    C239414
  1. Turn the shoe adjuster and expand the shoes until the disc locks.
    Text in Illustration 
    V100135
    Expand
    V100136
    Contract

  1. Turn and contract the shoe adjuster until the disc can rotate smoothly.

    Standard:
    Returns 8 notches.

  1. Check that there is no brake drag against the shoes.

  1. Install the parking brake shoe adjusting hole plug.

  1. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

    Parking brake pedal travel:
    7 to 10 notches at 300 N (31 kgf, 67.5 lbf)

  1. for TMC, TMMR Made:

    1. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. for TMMK Made:

    1. Using a wrench or an equivalent tool, hold the adjusting nut and install a new lock nut.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

  1. Check that the parking brake does not drag.

  1. Remove the hub nuts from the hub bolts.

  1. Install the rear wheels.

    Torque:
    103 N*m{ 1049 kgf*cm , 76 ft.*lbf }



17. INSTALL REAR WHEEL

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }