Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS (for TMMK Made)

BACK WINDOW GLASS (for TMMK Made) > REMOVAL

for Preparation Click here



1. REMOVE ROOF HEADLINING ASSEMBLY
(Click here)


2. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)


    B271094
  1. Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.



3. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)


    B271092
  1. Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.



4. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH


    B279428
  1. Remove the 2 nuts and child restraint seat anchor bracket sub-assembly LH.



5. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


  1. for Type A:



      B271090
    1. Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.



  1. for Type B:



      B414445
    1. Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.



6. REMOVE CENTER STOP LIGHT SET


    E226678E01
  1. Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to disengage the 4 claws.



    E231297
  1. Turn the center stop light set 180 degrees as shown by the arrow in the illustration.

    HINT:
    This makes it easier to disconnect the connector.

  1. Disconnect the connector and remove the center stop light set.



7. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER


    B271100
  1. Using a moulding remover, disengage the 2 claws and 2 guides to remove the child restraint seat tether anchor cover.

    HINT:
    Use the same procedure for the other 2 child restraint seat tether anchor covers.



8. REMOVE REAR SEAT SHOULDER BELT COVER


    B271099
  1. Using a moulding remover, disengage the 2 claws and 4 guides and remove the rear seat shoulder belt cover.

    HINT:
    Use the same procedure for the other 2 rear seat shoulder belt covers.



9. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    B279423E02
  1. Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape

    HINT:
    Tape the tip of the pliers before use.

  1. Disengage the 5 guides.

  1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.



10. REMOVE BACK WINDOW GLASS SUB-ASSEMBLY
  1. Disconnect each connector.



    B380729E01
  1. Apply protective tape to the area around the installation position of the back window glass sub-assembly on the vehicle body to prevent it from being scratched.
    Text in Illustration 
    *1
    Protective Tape



    B372488E01
  1. Using a knife, cut off the back window outside moulding as shown in the illustration.
    Text in Illustration 
    *a
    Cut Off



    B380736E01
  1. Place matchmarks on the back window glass sub-assembly and vehicle body at the locations indicated in the illustration.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Matchmarks are not necessary if the back window glass sub-assembly is not going to be reused.



    B380730E01
  1. Pass a piano wire between the vehicle body and back window glass sub-assembly from the interior.
    Text in Illustration 
    *1
    Stopper
    *a
    Piano Wire

  1. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

  1. Cut off the adhesive by pulling the piano wire around the back window glass sub-assembly.

    NOTICE:
    When removing the back window glass, take care not to damage the paint or interior and exterior ornaments.



  1. Disengage the back window glass stoppers.


    B380731E01


    Text in Illustration 
    *A
    for 1-piece Type
    *B
    for 2-piece Type
    *1
    No. 1 Back Window Glass Stopper
    *2
    No. 2 Back Window Glass Stopper

    NOTICE:
    1. The No. 1 back window glass stoppers and No. 2 back window glass stoppers are installed to the back window glass as shown in the illustration. Be careful not to damage the back window glass when cutting off the adhesive.
    2. To prevent the back window glass sub-assembly from falling when performing this operation, be sure to hold the back window glass sub-assembly using suction cups.

    HINT:
    Depending on the vehicle, either 1-piece type or 2-piece type stoppers may be present.

  1. Using suction cups, remove the back window glass sub-assembly.

    NOTICE:
    1. Be careful not to drop the back window glass sub-assembly.
    2. Leave as much adhesive on the vehicle body as possible when removing the back window glass sub-assembly.



11. REMOVE BACK WINDOW GLASS ADHESIVE DAM


  1. When reusing the back window glass:



      B280251E01
    1. Using a scraper, remove the back window glass adhesive dam from the back side of the back window glass.
      Text in Illustration 
      *A
      Back Side

      NOTICE:
      1. Be careful not to damage the back window glass.
      2. Be sure to replace the back window glass adhesive dam with a new one.



12. REMOVE BACK WINDOW OUTSIDE MOULDING


  1. When reusing the back window glass:



      B280234E01
    1. Using a scraper, remove the back window outside moulding from the back side of the back window glass.
      Text in Illustration 
      *A
      Back Side

      NOTICE:
      1. Be careful not to damage the back window glass.
      2. Be sure to replace the back window outside moulding with a new one.



13. REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 1-piece Type)


  1. When reusing the back window glass:



      B280235E01
    1. Using a scraper, remove the 2 No. 1 back window glass stoppers from the back side of the back window glass.
      Text in Illustration 
      *A
      Back Side

      NOTICE:
      1. Be careful not to damage the back window glass.
      2. Be sure to replace the 1-piece type No. 1 back window glass stoppers with new 2-piece type No. 1 and No. 2 back window glass stoppers.



14. REMOVE NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)


  1. When reusing the back window glass:



      B280235E01
    1. Using a scraper, remove the 2 No. 2 back window glass stoppers from the back side of the back window glass.
      Text in Illustration 
      *A
      Back Side

      NOTICE:
      1. Be careful not to damage the back window glass.
      2. Be sure to replace the No. 2 back window glass stoppers with new ones.



15. REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)


    B380732
  1. Remove the 2 No. 1 back window glass stoppers.

    NOTICE:
    Be sure to replace the No. 1 back window glass stoppers with new ones.



16. CLEAN BACK WINDOW GLASS
  1. Using a scraper, remove any remaining adhesive dam and adhesive residue from the back window glass.

    NOTICE:
    Be careful not to damage the back window glass.



    B187131
  1. Clean the outer circumference of the back window glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the back window glass surface after cleaning it.
    2. Even if using a new back window glass, clean it with a non-residue solvent.



17. CLEAN VEHICLE BODY


    B149737E07
  1. Clean and shape the contact surface of the vehicle body.
    Text in Illustration 
    *1
    Adhesive
    *2
    Vehicle Body

    1. Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

      NOTICE:
      Be careful not to damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.

      HINT:
      Even if all of the adhesive has been removed, clean the vehicle body.