Terminal No. (Symbol)
| Wiring Color
| Terminal Description
| Condition
| Specified Condition
|
A25-1 (BATT) - E26-16 (E1)
| GR - BR
| Battery (for measuring battery voltage and for ECM memory)
| Always
| 11 to 14 V
|
E26-29 (+BM) - E26-16 (E1)
| R - BR
| Power source of throttle actuator
| Always
| 11 to 14 V
|
A25-37 (IGSW) - E26-16 (E1)
| V - BR
| Ignition switch signal
| Ignition switch ON
| 11 to 14 V
|
A25-2 (+B) - E26-16 (E1)
| P - BR
| Power source of ECM
| Ignition switch ON
| 11 to 14 V
|
A25-3 (+B2) - E26-16 (E1)
| LG - BR
| Power source of ECM
| Ignition switch ON
| 11 to 14 V
|
E26-74 (OC1+) - E26-75 (OC1-)
| W - B
| Camshaft timing oil control valve assembly (for intake camshaft) operation signal
| Idling
| Pulse generation (See waveform 1)
|
E26-65 (OE1+) - E26-64 (OE1-)
| R - GR
| Camshaft timing oil control valve assembly (for exhaust camshaft) operation signal
| Idling
| Pulse generation (See waveform 2)
|
A25-46 (MREL) - E26-16 (E1)
| BE - BR
| EFI MAIN relay operation signal
| Ignition switch ON
| 11 to 14 V
|
E26-91 (VG) - E26-92 (E2G)
| G - LG
| Mass air flow meter sub-assembly signal
| Idling, shift lever in P or N, A/C switch off
| 0.5 to 3.0 V
|
E26-93 (THA) - E26-94 (ETHA)
| P - Y
| Intake air temperature sensor signal
| Idling, intake air temperature 20°C (68°F)
| 0.5 to 3.4 V
|
E26-95 (THW) - E26-96 (ETHW)
| B - P
| Engine coolant temperature sensor signal
| Idling, engine coolant temperature 80°C (176°F)
| 0.2 to 1.0 V
|
E26-125 (VCTA) - E26-126 (ETA)
| B - R
| Power source of throttle position sensor (specific voltage)
| Ignition switch ON
| 4.5 to 5.5 V
|
E26-127 (VTA1) - E26-126 (ETA)
| Y - R
| Throttle position sensor signal (for engine control)
| Ignition switch ON, accelerator pedal fully released
| 0.5 to 1.1 V
|
Ignition switch ON, accelerator pedal fully depressed
| 3.2 to 4.8 V
|
E26-128 (VTA2) - E26-126 (ETA)
| W - R
| Throttle position sensor signal (for sensor malfunction detection)
| Ignition switch ON, accelerator pedal fully released
| 2.1 to 3.1 V
|
Ignition switch ON, accelerator pedal fully depressed
| 4.6 to 5.0 V
|
A25-51 (VPA) - A25-52 (EPA)
| G - Y
| Accelerator pedal position sensor signal (for engine control)
| Ignition switch ON, accelerator pedal fully released
| 0.5 to 1.1 V
|
Ignition switch ON, accelerator pedal fully depressed
| 2.6 to 4.5 V
|
A25-54 (VPA2) - A25-55 (EPA2)
| R - BE
| Accelerator pedal position sensor signal (for sensor malfunction detection)
| Ignition switch ON, accelerator pedal fully released
| 1.2 to 2.0 V
|
Ignition switch ON, accelerator pedal fully depressed
| 3.4 to 4.75 V
|
A25-53 (VCPA) - A25-52 (EPA)
| P - Y
| Power source of accelerator pedal position sensor (for VPA)
| Ignition switch ON
| 4.5 to 5.5 V
|
A25-56 (VCP2) - A25-55 (EPA2)
| L - BE
| Power source of accelerator pedal position sensor (for VPA2)
| Ignition switch ON
| 4.5 to 5.5 V
|
E26-23 (HA1A) - E26-53 (E04)
| G - W-B
| Air fuel ratio sensor heater operation signal
| Idling
| Pulse generation (See waveform 3)
|
Ignition switch ON
| 11 to 14 V
|
E26-133 (A1A+) - E26-16 (E1)
| L - BR
| Air fuel ratio sensor signal
| Ignition switch ON
| 3.3 V*1
|
E26-134 (A1A-) - E26-16 (E1)
| P - BR
| Air fuel ratio sensor signal
| Ignition switch ON
| 2.9 V*1
|
E26-24 (HT1B) - E26-53 (E04)
| Y - W-B
| Heated oxygen sensor heater operation signal
| Idling
| Below 3.0 V
|
Ignition switch ON
| 11 to 14 V
|
E26-100 (OX1B) - E26-132 (EX1B)
| W - R
| Heated oxygen sensor signal
| Engine speed maintained at 2500 rpm for 2 minutes after warming up engine
| Pulse generation (See waveform 4)
|
E26-20 (#10) - E26-50 (E01)
| B - W-B
| No. 1 fuel injector assembly signal
| Ignition switch ON
| 11 to 14 V
|
Idling
| Pulse generation (See waveform 5)
|
E26-17 (#20) - E26-50 (E01)
| R - W-B
| No. 2 fuel injector assembly signal
| Ignition switch ON
| 11 to 14 V
|
Idling
| Pulse generation (See waveform 5)
|
E26-18 (#30) - E26-50 (E01)
| Y - W-B
| No. 3 fuel injector assembly signal
| Ignition switch ON
| 11 to 14 V
|
Idling
| Pulse generation (See waveform 5)
|
E26-19 (#40) - E26-50 (E01)
| L - W-B
| No. 4 fuel injector assembly signal
| Ignition switch ON
| 11 to 14 V
|
Idling
| Pulse generation (See waveform 5)
|
E26-123 (KNK1) - E26-124 (EKNK)
| R - G
| Knock control sensor signal
| Engine speed maintained at 4000 rpm after warming up engine
| Pulse generation (See waveform 6)
|
E26-82 (VV1+) - E26-114 (VV1-)
| V - L
| Camshaft position sensor signal (for intake camshaft)
| Idling
| Pulse generation (See waveform 7)
|
E26-81 (EV1+) - E26-112 (EV1-)
| P - W
| Camshaft position sensor signal (for exhaust camshaft)
| Idling
| Pulse generation (See waveform 7)
|
E26-76 (NE+) - E26-109 (NE-)
| B - W
| Crankshaft position sensor signal
| Idling
| Pulse generation (See waveform 8)
|
E26-57 (IGT1) - E26-16 (E1)
| Y - BR
| No. 1 ignition coil assembly (ignition signal)
| Idling
| Pulse generation (See waveform 9)
|
E26-56 (IGT2) - E26-16 (E1)
| R - BR
| No. 2 ignition coil assembly (ignition signal)
| Idling
| Pulse generation (See waveform 9)
|
E26-55 (IGT3) - E26-16 (E1)
| G - BR
| No. 3 ignition coil assembly (ignition signal)
| Idling
| Pulse generation (See waveform 9)
|
E26-54 (IGT4) - E26-16 (E1)
| L - BR
| No. 4 ignition coil assembly (ignition signal)
| Idling
| Pulse generation (See waveform 9)
|
E26-51 (IGF1) - E26-16 (E1)
| W - BR
| Ignition coil assembly (ignition confirmation signal)
| Ignition switch ON
| 4.5 to 5.5 V
|
Idling
| Pulse generation (See waveform 9)
|
E26-68 (PRG) - E26-50 (E01)
| W - W-B
| Purge VSV operation signal
| Ignition switch ON
| 11 to 14 V
|
Idling, under purge control
| Pulse generation (See waveform 10)
|
A25-57 (SPD) - E26-16 (E1)
| L - BR
| Vehicle speed signal from combination meter assembly
| Driving at 20 km/h (12 mph)
| Pulse generation (See waveform 11)
|
A25-22 (STA) - E26-16 (E1)
| LG - BR
| Starter assembly signal
| Cranking
| 5.5 V or higher
|
E26-63 (NSW) - E26-16 (E1)
| LG - BR
| Park/neutral position switch assembly signal
| Ignition switch ON, shift lever not in P or N
| 11 to 14 V
|
Ignition switch ON, shift lever in P or N
| Below 3.0 V
|
A25-11 (STP) - E26-16 (E1)
| BE - BR
| Stop light switch assembly signal
| Brake pedal depressed
| 7.5 to 14 V
|
Brake pedal released
| Below 1.5 V
|
A25-24 (ST1-) - E26-16 (E1)
| GR - BR
| Stop light switch assembly signal (opposite to voltage at STP terminal)
| Ignition switch ON, brake pedal depressed
| Below 1.5 V
|
Ignition switch ON, brake pedal released
| 7.5 to 14 V
|
E26-60 (M+) - E26-58 (ME01)
| W - W-B
| Throttle actuator operation signal (positive terminal)
| Idling with warm engine
| Pulse generation (See waveform 12)
|
E26-30 (M-) - E26-58 (ME01)
| B - W-B
| Throttle actuator operation signal (negative terminal)
| Idling with warm engine
| Pulse generation (See waveform 13)
|
A25-21 (FC) - E26-50 (E01)
| V - W-B
| Fuel pump control
| Ignition switch ON
| 11 to 14 V
|
A25-30 (W) - E26-16 (E1)
| LG - BR
| Malfunction Indicator Lamp (MIL) operation signal
| Ignition switch ON (MIL goes on)
| Below 3.0 V
|
Idling
| 11 to 14 V
|
A25-23 (TC) - E26-16 (E1)
| P - BR
| Terminal TC of DLC3
| Ignition switch ON
| 11 to 14 V
|
A25-31 (TACH) - E26-16 (E1)
| B - BR
| Engine speed signal
| Idling
| Pulse generation (See waveform 14)
|
E26-113 (VCV1) - E26-16 (E1)
| B - BR
| Power source of camshaft position sensor (for intake camshaft) (specific voltage)
| Ignition switch ON
| 4.5 to 5.5 V
|
E26-111 (VCE1) - E26-16 (E1)
| LG - BR
| Power source of camshaft position sensor (for exhaust camshaft) (specific voltage)
| Ignition switch ON
| 4.5 to 5.5 V
|
E26-73 (ALT) - E26-16 (E1)
| L - BR
| Generator assembly
| Ignition switch ON
| 11 to 14 V
|
A25-13 (CANH) - E26-16 (E1)
| B - BR
| CAN communication line
| Ignition switch ON
| Pulse generation (See waveform 15)
|
A25-26 (CANL) - E26-16 (E1)
| W - BR
| CAN communication line
| Ignition switch ON
| Pulse generation (See waveform 16)
|
E26-69 (ACIS) - E26-50 (E01)
| P - W-B
| Vacuum switching valve assembly for ACIS (Acoustic Control Induction System) operation signal
| Ignition switch ON
| 11 to 14 V
|
E26-22 (IA1+)*2 - E26-50 (E01)
| W - W-B
| Intake air control valve actuator for tumble control valve
| Idling with cold engine
| Pulse generation (See waveform 17)
|
E26-21 (IA1-)*2 - E26-50 (E01)
| G - W-B
| Intake air control valve actuator for tumble control valve
| Idling with cold engine
| Pulse generation (See waveform 18)
|
E26-131 (IAC1)*2 - E26-129 (EIA1)*2
| B - L
| Tumble control valve position sensor
| Ignition switch off to ON
| 3.0 to 4.0 V
|
E26-130 (VCIA)*2 - E26-16 (E1)
| B - BR
| Power source of tumble control valve position sensor (specific voltage)
| Ignition switch ON
| 4.5 to 5.5 V
|
A25-45 (NEO)*3 - E26-16 (E1)
| G - BR
| Crankshaft position sensor signal sent to certification ECU (smart key ECU assembly)
| Idling with warm engine
| Pulse generation (See waveform 19)
|
A25-5 (FANL) - E26-50 (E01)
| R - W-B
| Cooling fan motor operation signal (low)
| Ignition switch ON
| 11 to 14 V
|
Idling with A/C on, or high engine coolant temperature
| Below 1.5 V
|
A25-6 (FANH) - E26-50 (E01)
| W - W-B
| Cooling fan motor operation signal (high)
| Ignition switch ON
| 11 to 14 V
|
Idling with high engine coolant temperature
| Below 1.5 V
|
A25-14 (EC) - Body ground
| W-B - -
| Earth (ground) circuit of ECM
| Always
| Below 1 Ω
|
E26-50 (E01) - Body ground
| W-B - -
| Earth (ground) circuit of ECM
| Always
| Below 1 Ω
|
E26-49 (E02) - Body ground
| W-B - -
| Earth (ground) circuit of ECM
| Always
| Below 1 Ω
|
E26-58 (ME01) - Body ground
| W-B - -
| Earth (ground) circuit of ECM
| Always
| Below 1 Ω
|
E26-59 (GE01) - Body ground
| G - -
| Shielded earth (ground) circuit of throttle actuator
| Always
| Below 1 Ω
|