Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



A247842E65

HINT:
The standard voltage, resistance and waveform between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A84-1 (BATT) - E96-53 (E1)
GR - W-B
Battery (for measuring battery voltage and for ECM memory)
Always
11 to 14 V
A84-2 (+B) - E96-53 (E1)
P - W-B
Power source of ECM
Engine switch on (IG)
11 to 14 V
A84-3 (+B2) - E96-53 (E1)
LG - W-B
Power source of ECM
Engine switch on (IG)
11 to 14 V
A84-4 (FANH) - E96-51 (E01)
W - W-B
Cooling fan motor (high) operation signal
Engine switch on (IG)
11 to 14 V
Idling with high engine coolant temperature
Below 1.5 V
A84-6 (IGSW) - E96-53 (E1)
V - W-B
Ignition switch signal
Engine switch on (IG)
11 to 14 V
A84-8 (IREL) - E96-53 (E1)
L - W-B
EDU relay operation signal
Engine stopped, engine switch on (IG)
0 to 1.5 V
A84-9 (STP) - E96-53 (E1)
BE - W-B
Stop light switch assembly signal
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
A84-10 (ST1-) - E96-53 (E1)
GR - W-B
Stop light switch assembly signal (opposite to STP terminal)
Engine switch on (IG), brake pedal depressed
Below 1.5 V
Engine switch on (IG), brake pedal released
7.5 to 14 V
A84-13 (CANH) - E96-53 (E1)
B - W-B
CAN communication signal
Engine switch on (IG)
Pulse generation
(see waveform 1)
A84-14 (EC) - Body ground
W-B - -
Ground
Always
Below 1 Ω
A84-17 (FANL) - E96-51 (E01)
R - W-B
Cooling fan motor (low) operation signal
Engine switch on (IG)
11 to 14 V
Idling with A/C on, or high engine coolant temperature
Below 1.5 V
A84-21 (FPC) - E96-53 (E1)
W - W-B
Fuel pump control
Engine stopped, engine switch on (IG)
Below 1.5 V
A84-26 (CANL) - E96-53 (E1)
W - W-B
CAN communication signal
Engine switch on (IG)
Pulse generation
(see waveform 2)
A84-27 (W) - E96-53 (E1)
LG - W-B
Malfunction Indicator Lamp (MIL) operation signal
Engine switch on (IG)
(MIL illuminated)
Below 3.0 V
Idling
11 to 14 V
A84-29 (STA) - E96-53 (E1)
LG - W-B
Starter signal
Cranking
6.0 V or higher
A84-30 (NEO) - E96-53 (E1)
G - W-B
Crankshaft position sensor signal sent to certification ECU (smart key ECU assembly)
Idling with warm engine
Pulse generation
(see waveform 3)
A84-31 (TACH) - E96-53 (E1)
B - W-B
Engine speed signal
Idling with warm engine
Pulse generation
(see waveform 4)
A84-33 (TC) - E96-53 (E1)
P - W-B
Terminal TC of DLC3
Engine stopped, engine switch on (IG)
11 to 14 V
A84-44 (SPD) - E96-53 (E1)
L - W-B
Vehicle speed signal from combination meter assembly
Driving at 20 km/h (12 mph)
Pulse generation
(see waveform 5)
A84-46 (MREL) - E96-53 (E1)
BE - W-B
EFI MAIN relay operation signal
Engine switch on (IG)
11 to 14 V
A84-47 (VPA) - A84-48 (EPA)
G - Y
Accelerator pedal position sensor signal (for engine control)
Engine switch on (IG), accelerator pedal fully released
0.5 to 1.1 V
Engine switch on (IG), accelerator pedal fully depressed
2.6 to 4.5 V
A84-49 (VCPA) - A84-48 (EPA)
P - Y
Power source of accelerator pedal position sensor (for VPA)
Engine switch on (IG)
4.5 to 5.5 V
A84-50 (VPA2) - A84-51 (EPA2)
R - BE
Accelerator pedal position sensor signal
Engine switch on (IG), accelerator pedal fully released
1.2 to 2.0 V
Engine switch on (IG), accelerator pedal fully depressed
3.4 to 4.75 V
A84-52 (VCP2) - A84-51 (EPA2)
L - BE
Power source of accelerator pedal position sensor (for VPA2)
Engine switch on (IG)
4.5 to 5.5 V
A84-57 (NSW) - E96-53 (E1)
L - W-B
Park/Neutral position switch assembly signal
Engine switch on (IG) and shift lever in P or N
Below 3.0 V
A84-58 (KSW) - E96-53 (E1)
G - W-B
Key in vehicle signal
Engine switch off → on (IG)
0 to 3.0 V
A84-59 (S) - E96-53 (E1)
G - W-B
S shift position signal
Engine switch on (IG), shift lever in S
11 to 14 V
Engine switch on (IG), shift lever not in S
Below 1 V
E96-9 (OC1+) - E96-8 (OC1-)
GR - B
Cam timing oil control solenoid assembly operation signal
Idling
Pulse generation
(See waveform 6)
E96-16 (M+) - E96-49 (ME01)
W - W-B
Throttle actuator operation signal
(positive terminal)
Idling with warm engine
Pulse generation
(See waveform 7)
E96-17 (HT1B) - E96-53 (E1)
L - W-B
Heated oxygen sensor (sensor 2) heater operation signal
Engine switch on (IG)
11 to 14 V
Idling
Below 3.0 V
E96-18 (E04) - Body ground
W-B - -
Ground
Always
Below 1 Ω
E96-19 (HA1A) - E96-18 (E04)
G - W-B
Air fuel ratio sensor (sensor 1) heater operation signal
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(See waveform 8)
E96-21 (#2D+) - E96-20 (#2D-)
BR - G
No. 2 fuel injector assembly (for direct injection) signal
Idling with warm engine, Data List item "Injection Mode" displaying "Direct"
Pulse generation
E96-22 (#3D+) - E96-23 (#3D-)
L - Y
No. 3 fuel injector assembly (for direct injection) signal
Idling with warm engine, Data List item "Injection Mode" displaying "Direct"
Pulse generation
E96-25 (#4D+) - E96-24 (#4D-)
P - V
No. 4 fuel injector assembly (for direct injection) signal
Idling with warm engine, Data List item "Injection Mode" displaying "Direct"
Pulse generation
E96-26 (#1D+) - E96-27 (#1D-)
B - W
No. 1 fuel injector assembly (for direct injection) signal
Idling with warm engine, Data List item "Injection Mode" displaying "Direct"
Pulse generation
E96-28 (FP1+) - E96-29 (FP1-)
BR - G
Fuel pump (for high pressure side) signal
Engine running (direct injection control)
Pulse generation
E96-30 (+BD1) - E96-53 (E1)
L - W-B
Power source of ECU
(injector driver)
Engine stopped, engine switch on (IG)
11 to 14 V
E96-32 (EGR4) - E96-53 (E1)
LG - W-B
EGR valve assembly
EGR valve operating
Pulse generation
(See waveform 9)
E96-33 (EGR2) - E96-53 (E1)
W - W-B
EGR valve assembly
EGR valve operating
Pulse generation
(See waveform 9)
E96-34 (D) - E96-53 (E1)
G - W-B
D shift position signal
Engine switch on (IG), shift lever in D or S
11 to 14 V
Engine switch on (IG), shift lever not in D or S
Below 1 V
E96-35 (R) - E96-53 (E1)
GR - W-B
R shift position signal
Engine switch on (IG), shift lever in R
11 to 14 V
Engine switch on (IG), shift lever not in R
Below 1 V
E96-36 (EGR1) - E96-53 (E1)
Y - W-B
EGR valve assembly
EGR valve operating
Pulse generation
(See waveform 9)
E96-37 (EGR3) - E96-53 (E1)
R - W-B
EGR valve assembly
EGR valve operating
Pulse generation
(See waveform 9)
E96-38 (OE1+) - E96-68 (OE1-)
R - GR
Camshaft timing oil control valve assembly operation signal
Idling
Pulse generation
(See waveform 10)
E96-39 (IGT4) - E96-53 (E1)
V - W-B
No. 4 ignition coil assembly (ignition signal)
Idling with warm engine
Pulse generation
(See waveform 11)
E96-40 (IGT3) - E96-53 (E1)
G - W-B
No. 3 ignition coil assembly (ignition signal)
Idling with warm engine
Pulse generation
(See waveform 11)
E96-41 (IGT2) - E96-53 (E1)
P - W-B
No. 2 ignition coil assembly (ignition signal)
Idling with warm engine
Pulse generation
(See waveform 11)
E96-42 (IGT1) - E96-53 (E1)
Y - W-B
No. 1 ignition coil assembly (ignition signal)
Idling with warm engine
Pulse generation
(See waveform 11)
E96-46 (M-) - E96-49 (ME01)
B - W-B
Throttle actuator operation signal (negative terminal)
Idling with warm engine
Pulse generation
(see waveform 12)
E96-47 (GE01) - Body ground
G - -
Shielded earth (ground) circuit of throttle actuator
Always
Below 1 Ω
E96-48 (+BM) - E96-53 (E1)
R - W-B
Power source of throttle actuator
Always
11 to 14 V
E96-49 (ME01) - Body ground
W-B - -
Ground
Always
Below 1 Ω
E96-50 (E02) - Body ground
W-B - -
Ground
Always
Below 1 Ω
E96-51 (E01) - Body ground
W-B - -
Ground
Always
Below 1 Ω
E96-53 (E1) - Body ground
W-B - -
Ground
Always
Below 1 Ω
E96-54 (#20) - E96-53 (E1)
R - W-B
No. 2 fuel injector assembly (for port injection) signal
Idling with warm engine, Data List item "Injection Mode" displaying "Port"
Pulse generation
(see waveform 13)
E96-55 (#30) - E96-53 (E1)
Y - W-B
No. 3 fuel injector assembly (for port injection) signal
Idling with warm engine, Data List item "Injection Mode" displaying "Port"
Pulse generation
(see waveform 13)
E96-56 (#40) - E96-53 (E1)
G - W-B
No. 4 fuel injector assembly (for port injection) signal
Idling with warm engine, Data List item "Injection Mode" displaying "Port"
Pulse generation
(see waveform 13)
E96-57 (#10) - E96-53 (E1)
L - W-B
No. 1 fuel injector assembly (for port injection) signal
Idling with warm engine, Data List item "Injection Mode" displaying "Port"
Pulse generation
(see waveform 13)
E96-58 (E1D2) - Body ground
W - -
Ground
Always
Below 1 Ω
E96-59 (E1D1) - Body ground
B - -
Ground
Always
Below 1 Ω
E96-60 (+BD2) - E96-53 (E1)
Y - W-B
EDU relay signal
Engine stopped, engine switch on (IG)
11 to 14 V
E96-64 (P) - E96-53 (E1)
B - W-B
P shift position signal
Engine switch on (IG), shift lever in P
11 to 14 V
Engine switch on (IG), shift lever not in P
Below 1 V
E96-65 (N) - E96-53 (E1)
L - W-B
N shift position signal
Engine switch on (IG), shift lever in N
11 to 14 V
Engine switch on (IG), shift lever not in N
Below 1 V
E96-70 (PRG) - E96-53 (E1)
L - W-B
Purge VSV for EVAP system operation signal
Engine switch on (IG)
11 to 14 V
Idling with warm engine, under purge control
Pulse generation
(see waveform 14)
E96-76 (NE+) - E96-109 (NE-)
B - R
Crankshaft position sensor signal
Idling with warm engine
Pulse generation
(see waveform 15)
E96-81 (EV1+) - E96-112 (EV1-)
P - W
Camshaft position sensor (for exhaust camshaft) signal
Idling with warm engine
Pulse generation
(see waveform 16)
E96-82 (VV1+) - E96-114 (VV1-)
V - L
Camshaft position sensor (for intake camshaft) signal
Idling with warm engine
Pulse generation
(see waveform 16)
E96-88 (VTA2) - E96-120 (ETA)
L - R
Throttle position sensor signal (for sensor malfunction detection)
Engine switch on (IG), accelerator pedal fully released
2.1 to 3.1 V
Idling, accelerator pedal fully depressed
4.6 to 5.0 V
E96-90 (VCVG) - E96-91 (E2G)
Y - LG
Power source of mass air flow meter sub-assembly
Engine switch on (IG)
4.8 to 5.2 V
E96-92 (VG) - E96-91 (E2G)
G - LG
Mass air flow meter sub-assembly signal
Engine switch on (IG)
Pulse generation
(See waveform 17)
E96-94 (THA) - E96-91 (E2G)
P - LG
Intake air temperature sensor signal
Idling, intake air temperature 0 to 80°C (32 to 176°F)
0.5 to 3.4 V
E96-97 (THEO) - E96-96 (ETHE)
LG - P
Engine oil temperature sensor signal
Idling with warm engine
0 to 5.0 V
E96-98 (PEO) - E96-129 (EPEO)
G - W
Oil pressure sender gauge assembly signal
Idling with warm engine
0.5 to 4.5 V
E96-99 (OX1B) - E96-100 (EX1B)
W - R
Heated oxygen sensor signal
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine
Pulse generation
(See waveform 18)
E96-101 (IGF1) - E96-53 (E1)
W - W-B
Ignition coil assembly (ignition confirmation signal)
Engine switch on (IG)
4.5 to 5.5 V
Idling with warm engine
Pulse generation
(See waveform 11)
E96-103 (PR) - E96-135 (EPR)
B - Y
Fuel pressure sensor signal
Idling with warm engine
0.5 to 4.5 V
E96-104 (THW) - E96-105 (ETHW)
W - P
Engine coolant temperature sensor signal
Idling, engine coolant temperature 75 to 100°C (167 to 212°F)
0.2 to 1.0 V
E96-106 (PIM) - E96-137 (EPIM)
Y - B
Manifold absolute pressure sensor signal
Engine switch on (IG)
3.0 to 5.0 V
E96-110 (VCNE) - E96-53 (E1)
W - W-B
Power source of crankshaft position sensor
Engine switch on (IG)
4.5 to 5.5 V
E96-111 (VCE1) - E96-53 (E1)
LG - W-B
Power source of camshaft position sensor (for exhaust camshaft)
Engine switch on (IG)
4.5 to 5.5 V
E96-113 (VCV1) - E96-53 (E1)
B - W-B
Power source of camshaft position sensor (for intake camshaft)
Engine switch on (IG)
4.5 to 5.5 V
E96-121 (VCTA) - E96-120 (ETA)
B - R
Power source of throttle position sensor (specific voltage)
Engine switch on (IG)
4.5 to 5.5 V
E96-122 (VTA1) - E96-120 (ETA)
P - R
Throttle position sensor signal (for engine control)
Engine switch on (IG), accelerator pedal fully released
0.5 to 1.1 V
Idling, accelerator pedal fully depressed
3.2 to 4.8 V
E96-124 (KNK1) - E96-123 (EKNK)
W - B
Knock control sensor signal
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(See waveform 19)
E96-130 (VCPE) - E96-53 (E1)
Y - W-B
Power source of engine oil sender gauge assembly
Engine switch on (IG)
4.75 to 5.25 V
E96-131 (A1A+) - E96-53 (E1)
L - W-B
Air fuel ratio sensor signal
Engine switch on (IG)
3.0 to 3.6 V*
E96-132 (A1A-) - E96-53 (E1)
P - W-B
Air fuel ratio sensor signal
Engine switch on (IG)
2.7 to 3.3 V*
E96-136 (VCPR) - E96-53 (E1)
L - W-B
Power source of fuel pressure sensor
Engine switch on (IG)
4.75 to 5.25 V
E96-138 (VCPM) - E96-53 (E1)
W - W-B
Power source of manifold absolute pressure sensor
Engine switch on (IG)
4.75 to 5.25 V
*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1
A292386E02
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANH and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Engine switch on (IG)

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 2
A292387E02
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANL and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Engine switch on (IG)

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 3
A287796E04
Crankshaft Position Sensor Signal Sent to Certification ECU (Smart Key ECU Assembly) 
ECM Terminal Name
Between NEO and E1
Tester Range
1 V/DIV., 2 ms./DIV.
Condition
Idling with warm engine

WAVEFORM 4
A346596E01
Engine Speed Signal 
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling with warm engine

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 5
A292384E01
Vehicle Speed Signal 
ECM Terminal Name
Between SPD and E1
Tester Range
2 V/DIV., 20 ms./DIV.
Condition
Driving at 20 km/h (12 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 6
A292381E01
Cam Timing Oil Control Solenoid Assembly Operation Signal 
ECM Terminal Name
Between OC1+ and OC1-
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling

WAVEFORM 7
A208000E31
Throttle Actuator Positive Terminal Signal 
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 8
A205412E04
Air Fuel Ratio Sensor (Sensor 1) Heater Operation Signal 
ECM Terminal Name
Between HA1A and E04
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling

WAVEFORM 9
A214026E04
EGR Valve Assembly Signal 
ECM Terminal Name
Between EGR1 and E1
Between EGR2 and E1
Between EGR3 and E1
Between EGR4 and E1
Tester Range
20 V/DIV., 50 ms./DIV.
Condition
EGR valve operating

WAVEFORM 10
A292381E02
Camshaft Timing Oil Control Valve Assembly Operation Signal 
ECM Terminal Name
Between OE1+ and OE1-
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling

WAVEFORM 11
A289263E05
Ignition Coil Assembly Signal (IGT and IGF Signal) 
ECM Terminal Name
CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range
2 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 12
A245848E30
Throttle Actuator Negative Terminal Signal 
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 13
A292383E01
No. 1 (to No. 4) Fuel Injector Assembly (for Port Injection) Signal 
ECM Terminal Name
Between #10 (to #40) and E1
Tester Range
20 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine, Data List item "Injection Mode" displaying "Port"

HINT:
  1. The wavelength becomes shorter as the engine speed increases.
  2. When the port injection injectors are operating, Port is displayed for Injection Mode of the Data List.


WAVEFORM 14
A218020E07
Purge VSV Operation Signal 
ECM Terminal Name
Between PRG and E1
Tester Range
10 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine, under purge control

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 15
A200774E05
Crankshaft Position Sensor Signal 
ECM Terminal Name
Between NE+ and NE-
Tester Range
2 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 16
A255508E19
Camshaft Position Sensor Signal (for Intake and Exhaust Camshaft) 
ECM Terminal Name
CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 17
A337204E01
Mass Air Flow Meter Sub-assembly Signal 
ECM Terminal Name
Between VG and E2G
Tester Range
1 V/DIV., 100 μs./DIV.
Condition
Engine switch on (IG)

WAVEFORM 18
A292382E01
Heated Oxygen Sensor (Sensor 2) Signal 
ECM Terminal Name
Between OX1B and EX1B
Tester Range
0.2 V/DIV., 200 ms./DIV.
Condition
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:
In the Data List, the item O2 Sensor Voltage B1S2 shows the values input to the ECM from the heated oxygen sensor.


WAVEFORM 19
A283572E03
Knock Control Sensor Signal 
ECM Terminal Name
Between KNK1 and EKNK
Tester Range
1 V/DIV., 1 ms./DIV.
Condition
Engine speed maintained at 4000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine speed increases.
  2. The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.