Home › Engine / Hybrid System ยท 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > FAIL-SAFE CHART

for Preparation Click here


If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily or stops fuel injection.

DTC
Component
Fail-Safe Operation
Fail-Safe Deactivation Condition
P001100
P001500
VVT system
  1. Idle up (control of combustion decreased).
  2. Fuel-cut control is stopped.
Pass condition detected
P003012
P003013
P101A9E
Air fuel ratio sensor heater
The ECM turns off the air fuel ratio sensor heater.
Engine switch off
P003612
P003614
P102A9E
Heated oxygen sensor heater
The ECM turns off the heated oxygen sensor heater.
Engine switch off
P008700
P008800
P123513
Fuel pump (for high pressure side)
  1. The ECM performs fuel-cut when the engine speed and engine load are high.
  2. Fuel pressure is set at 200 kPa.
Engine switch off
P010012
P010014
Mass air flow meter sub-assembly
The ECM calculates fuel injection volume according to the engine speed and throttle valve position.
Pass condition detected
P011011
P011015
Intake air temperature sensor
The ECM estimates intake air temperature to be 20°C (68°F).
Pass condition detected and then engine switch turned off
P011511
P011515
Engine coolant temperature sensor
The ECM estimates engine coolant temperature to be 80°C (176°F).
Pass condition detected
P012011
P012015
P01201C
P022011
P022015
P060444
P060604
P060629
P060647
P060A47
P060B49
P060D49
P060E49
P061E49
P065714
P06579E
P160700
P210014
P210015
P211172
P211173
P211900
P211904
P211977
P21352B
Electronic throttle control system
The ECM cuts throttle actuator current and the throttle valve is returned to a 7° opening angle by the return spring.
The ECM then adjusts the engine output by controlling fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal angle to allow the vehicle to be driven at a minimal speed*.
Pass condition detected and then engine switch turned off
P019011
P019015
Fuel pressure sensor
  1. The ECM performs fuel-cut when the engine speed and engine load are high.
  2. Fuel pressure is set to 200 kPa.
Pass condition detected and then engine switch turned off
P020113
P020213
P020313
P020413
P062D13
Injector driver (built into ECM)
The ECM performs fuel-cut when the engine speed is 2000 rpm or more.
Pass condition detected and then engine switch turned off
P032511
P032515
Knock control sensor
The ECM sets the ignition timing to maximum retard.
Engine switch off
P035113
P035213
P035313
P035413
Ignition coil assembly
The ECM cuts the fuel injection.
Pass condition detected
P040314
P140000
P140596
P141004
EGR valve assembly
The ECM assumes that the EGR valve assembly is closed and controls the ignition timing.
Pass condition detected and then engine switch turned off
P05042B
Stop light switch assembly
The accelerator pedal opening angle is fixed if there is an accelerator pedal malfunction or history of a malfunction.
Pass condition detected and then engine switch turned off
P052400
Oil pressure sender gauge assembly
Engine speed is limited due to fuel cut and throttle restriction (4000 rpm or less).
Pass condition detected
P056014
ECM +B circuit
Generator command is controlled.
Pass condition detected and then engine switch turned off
P21CF13
P21D013
P21D113
P21D213
Fuel injector assembly
(for port injection)
The ECM performs fuel-cut when the engine speed is 2000 rpm or more.
Pass condition detected and then engine switch turned off
P212012
P212014
P21201C
P21201F
P212099
P212512
P212514
P21251F
P21382B
Accelerator pedal position sensor
The accelerator pedal position sensor has 2 sensor circuits: Main and Sub.
If there is a malfunction in either circuit, the ECM limits the engine output.
If there is a malfunction in both circuits, the ECM regards the accelerator pedal as being released.
As a result, the throttle valve is closed and the engine idles.
Pass condition detected and then engine switch turned off
P223711
P223712
P223714
P223716
P223717
P22371A
P225111
P225112
Air fuel ratio sensor
Air fuel ratio feedback control is stopped.
Pass condition detected and then engine switch turned off

HINT:
*: The vehicle can be driven slowly if the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.