Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Parking Brake SW
    Parking brake switch signal/ON or OFF
    ON: Parking brake switch on
    OFF: Parking brake switch off
    -
    Dimmer SW
    Dimmer switch high position signal/ON or OFF
    ON: Dimmer switch in high or high flash position
    OFF: Dimmer switch in low position
    -
    Passing Light SW
    Dimmer switch high flash position (pass) signal/ON or OFF
    ON: Dimmer switch in high flash position
    OFF: Dimmer switch not in high flash position
    -
    Rear Fog Light SW*1
    Rear fog light switch signal/ON or OFF
    ON: Rear fog light switch on
    OFF: Rear fog light switch off
    -
    Front Fog Light SW*2
    Front fog light switch signal/ON or OFF
    ON: Front fog light switch on
    OFF: Front fog light switch off
    -
    Auto Light SW
    Light control switch AUTO position signal/ON or OFF
    ON: Light control switch in AUTO position
    OFF: Light control switch not in AUTO position
    -
    Head Light SW (Head)
    Light control switch head position signal/ON or OFF
    ON: Light control switch in head position
    OFF: Light control switch not in head position
    -
    Head Light SW (Tail)
    Light control switch tail position signal/ON or OFF
    ON: Light control switch in tail or head position
    OFF: Light control switch in neither tail nor head position
    -
    Illumination Rate Info
    Illumination rate information/0.00 ms. to 2162.65 ms.
    Value is output according to ambient light levels
    -
    Response Time
    Delay timing of lighting the taillights when the automatic light control sensor detects brightness change/Normal or Long
    Customize setting displayed
    -
    Sensitivity
    Sensitivity of the automatic light control system/Light2, Light1, Normal, Dark1 or Dark2
    Customize setting displayed
    -
    DRL Function*3
    DRL function/ON or OFF
    Customize setting displayed
    -
    Disp Ex ON Sen
    Ambient brightness level required to dim display lights (combination meter, navigation display etc.)/Light2, Light1, Normal, Dark1 or Dark2
    Customize setting displayed
    -
    Disp Ex OFF Sen
    Ambient brightness level required to cancel dimming display lights (combination meter, navigation display etc.)/Light2, Light1, Normal, Dark1 or Dark2
    Customize setting displayed
    -

    1. *1: w/ Rear Fog Light
    2. *2: w/ Front Fog Light
    3. *3: for TMMK Made

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Turn Signal Switch (Right)
    Turn signal switch (right) signal/ON or OFF
    ON: Turn signal switch (right) on
    OFF: Turn signal switch (right) off
    -
    Turn Signal Switch (Left)
    Turn signal switch (left) signal/ON or OFF
    ON: Turn signal switch (left) on
    OFF: Turn signal switch (left) off
    -
    Hazard Flasher Switch
    Hazard switch signal/ON or OFF
    ON: Hazard switch on
    OFF: Hazard switch off
    -
    Turn Switch Signal (Full Turn)
    Turn signal switch (full turn) signal/ON or OFF
    ON: Turn signal switch (left or right) on
    OFF: Turn signal switch (left and right) off
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Daytime Running Light
    Daytime running lights
    ON/OFF
    -
    Taillight Relay
    Taillight relay
    ON/OFF
    -
    Headlight Relay
    Low beam headlights
    ON/OFF
    -
    Head Light Hi
    High beam headlights
    ON/OFF
    -
    Front Fog Light Relay*2
    Front fog lights
    ON/OFF
    Light control switch is in tail position
    Rear Fog Light Relay*1
    Rear fog lights
    ON/OFF
    Light control switch is in tail position
    Dimmer Signal
    Dimmer signal
    ON/OFF
    -

    1. *1: w/ Rear Fog Light
    2. *2: w/ Front Fog Light