Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HIGH BEAM SYSTEM

AUTOMATIC HIGH BEAM SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body / Main Body / Data List.

  5. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Dimmer SW
    Dimmer switch high position signal/ON or OFF
    ON: Dimmer switch in high or high flash position
    OFF: Dimmer switch in low position
    -
    Auto Light SW
    Light control switch AUTO position signal/ON or OFF
    ON: Light control switch in AUTO position
    OFF: Light control switch not in AUTO position
    -
    Head Light SW (Head)
    Light control switch head position signal/ON or OFF
    ON: Light control switch in head position
    OFF: Light control switch not in head position
    -
    Illumination Rate Info
    Illumination rate information/0.00 ms. to 2162.65 ms.
    Value is output according to ambient light levels
    -
    Auto H Beam STS0
    Automatic high beam sensor current state/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    Condition can be displayed
    Undetec: Undetected
    CAM NA: Camera detection malfunction
    No sens: No detection
    Hlight: Oncoming vehicles with headlights on
    Taillgt: Preceding vehicles with taillights on
    Speed: Vehicle speed
    Daytime: Daytime state
    Village: Urban area
    Malfunc: Malfunction
    Delay: Standby mode
    Aim Lmt: Aiming misalignment
    SAE Mod: SAE mode
    Undefin: Undefined state
    LIN Err: LIN communication error
    Auto H Beam STS1
    Automatic high beam sensor state past 1/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    Condition can be displayed
    Undetec: Undetected
    CAM NA: Camera detection malfunction
    No sens: No detection
    Hlight: Oncoming vehicles with headlights on
    Taillgt: Preceding vehicles with taillights on
    Speed: Vehicle speed
    Daytime: Daytime state
    Village: Urban area
    Malfunc: Malfunction
    Delay: Standby mode
    Aim Lmt: Aiming misalignment
    SAE Mod: SAE mode
    Undefin: Undefined state
    LIN Err: LIN communication error
    Auto H Beam STS2
    Automatic high beam sensor state past 2/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    Condition can be displayed
    Undetec: Undetected
    CAM NA: Camera detection malfunction
    No sens: No detection
    Hlight: Oncoming vehicles with headlights on
    Taillgt: Preceding vehicles with taillights on
    Speed: Vehicle speed
    Daytime: Daytime state
    Village: Urban area
    Malfunc: Malfunction
    Delay: Standby mode
    Aim Lmt: Aiming misalignment
    SAE Mod: SAE mode
    Undefin: Undefined state
    LIN Err: LIN communication error
    Auto H Beam STS3
    Automatic high beam sensor state past 3/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    Condition can be displayed
    Undetec: Undetected
    CAM NA: Camera detection malfunction
    No sens: No detection
    Hlight: Oncoming vehicles with headlights on
    Taillgt: Preceding vehicles with taillights on
    Speed: Vehicle speed
    Daytime: Daytime state
    Village: Urban area
    Malfunc: Malfunction
    Delay: Standby mode
    Aim Lmt: Aiming misalignment
    SAE Mod: SAE mode
    Undefin: Undefined state
    LIN Err: LIN communication error
    Auto H Beam STS4
    Automatic high beam sensor state past 4/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    Condition can be displayed
    Undetec: Undetected
    CAM NA: Camera detection malfunction
    No sens: No detection
    Hlight: Oncoming vehicles with headlights on
    Taillgt: Preceding vehicles with taillights on
    Speed: Vehicle speed
    Daytime: Daytime state
    Village: Urban area
    Malfunc: Malfunction
    Delay: Standby mode
    Aim Lmt: Aiming misalignment
    SAE Mod: SAE mode
    Undefin: Undefined state
    LIN Err: LIN communication error
    Auto H Beam STS5
    Automatic high beam sensor state past 5/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    Condition can be displayed
    Undetec: Undetected
    CAM NA: Camera detection malfunction
    No sens: No detection
    Hlight: Oncoming vehicles with headlights on
    Taillgt: Preceding vehicles with taillights on
    Speed: Vehicle speed
    Daytime: Daytime state
    Village: Urban area
    Malfunc: Malfunction
    Delay: Standby mode
    Aim Lmt: Aiming misalignment
    SAE Mod: SAE mode
    Undefin: Undefined state
    LIN Err: LIN communication error
    Auto H Beam STS6
    Automatic high beam sensor state past 6/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    Condition can be displayed
    Undetec: Undetected
    CAM NA: Camera detection malfunction
    No sens: No detection
    Hlight: Oncoming vehicles with headlights on
    Taillgt: Preceding vehicles with taillights on
    Speed: Vehicle speed
    Daytime: Daytime state
    Village: Urban area
    Malfunc: Malfunction
    Delay: Standby mode
    Aim Lmt: Aiming misalignment
    SAE Mod: SAE mode
    Undefin: Undefined state
    LIN Err: LIN communication error
    Auto H Beam STS7
    Automatic high beam sensor state past 7/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err
    Condition can be displayed
    Undetec: Undetected
    CAM NA: Camera detection malfunction
    No sens: No detection
    Hlight: Oncoming vehicles with headlights on
    Taillgt: Preceding vehicles with taillights on
    Speed: Vehicle speed
    Daytime: Daytime state
    Village: Urban area
    Malfunc: Malfunction
    Delay: Standby mode
    Aim Lmt: Aiming misalignment
    SAE Mod: SAE mode
    Undefin: Undefined state
    LIN Err: LIN communication error


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body / Automatic High Beam / Active Test.

  5. Perform the Active Test according to the display on the GTS.

    Automatic High Beam 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Automatic High Beam Operation
    Automatic high beam system operation
    ON/OFF
    ON: Operation start
    OFF: Operation stop