Home › Vehicle Exterior › LIGHTING (EXT) › AFS (ADAPTIVE FRONT-LIGHTING SYSTEM)

AFS (ADAPTIVE FRONT-LIGHTING SYSTEM) > FAIL-SAFE CHART

for Preparation Click here



AFS
If the AFS ECU (headlight swivel ECU assembly) detects a malfunction in the AFS or automatic headlight beam level control system, it will take the actions indicated in the table below.

Item
Abnormality Detection Condition
Leveling Motor Fail-safe Control
Swivel Motor Fail-safe Control
Return Condition
Warning Indicator
Headlight swivel motor
Communication stop
Lowers the headlight leveling motor 0.65° and continues control.
Returns the both headlights to the front position.
Signals are received normally.
Flashes
  1. Open circuit
  2. Short circuit
  3. Overheat
  4. Gear malfunction
  1. Returns the normal headlight swivel motor to the front position.
  2. Stops the abnormal headlight swivel motor at the current position.
Ignition switch is turned to ON again.
Abnormal voltage
Normal value is detected.
Does not illuminate
Headlight leveling motor
Communication stop
  1. If the position is higher than the initial position, the headlight leveling motor is returned to the initial position.
  2. If the position is lower than the initial position, the headlight leveling motor is stopped at the current position.
Returns the both headlight swivel motors to the initial position.
Signals are received normally.
Flashes
  1. Open circuit
  2. Short circuit
  3. Overheat
  1. Stops the abnormal headlight leveling motor at the current position.
  2. If position of normal motor is higher than the initial position, it is returned to the initial position. If the position of the normal motor is lower than the initial position, it is stopped at the current position.
Ignition switch is turned to ON again.
Abnormal voltage
Normal value is detected.
Does not illuminate
Steering angle sensor
Abnormal steering angle sensor
Continues control.
Returns the both headlights to the front position.
Ignition switch is turned to ON again.
Flashes
Wheel speed
Abnormal wheel speed sensor
  1. If either of the wheel speed signals is abnormal, control continues using the normal signal.
  2. If both of the wheel speed signals are abnormal, judgment is performed as though the vehicle is stationary and control continues.
Continues control using the same speed as before the sensor malfunction detection, the headlight swivel motors are returned to the initial position.
When the sensor(s) return to normal.
Flashes
Height control sensor
Abnormal vehicle angle (front to rear inclination)
  1. If the headlight leveling motor position is higher than the initial position, the headlight leveling motors are returned to the initial position.
  2. If the headlight leveling motor position is lower than the initial position, the headlight leveling motors are stopped at the current position.
Returns both headlight swivel motors to the initial position.
Normal value is detected.
Flashes
Power source malfunction
Ignition switch is turned to ON again.
Abnormal height control sensor signal
Normal value is detected.
CAN communication
Main body ECU (multiplex network body ECU) communication error (headlight signal)
Continues control.
Returns the both headlight swivel motors to the initial position.
Signals are received normally.
Flashes
Main body ECU (multiplex network body ECU) communication error (destination information, VAST request, time stamp)
Continues control.
ECM communication error (power source mode on IG signal)
ECT ECU communication error (gear signal)
Returns the both headlight swivel motors to the initial position.
Steering sensor communication error (steering angle signal)
Skid control ECU communication error (vehicle speed signal)
Control continues. Control is performed as though the vehicle is stationary.
AFS ECU
Abnormal AFS ECU
Continues control.
Continues control.
Ignition switch is turned to ON again.
Flashes
Initialization of height control sensor
Initialization of height control sensor not completed
Adjusts the headlight leveling motor position to a step value so that the height will be as same as that of an unloaded vehicle.
Returns the both headlight swivel motors to the initial position.
Initialization is completed
Flashes (6 times)
Abnormal height sensor data at initialization
Flashes