Home › Engine / Hybrid System ยท CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > Cruise Main Indicator Light Circuit

for Preparation Click here


DESCRIPTION

  1. The ECM turns on the cruise control indicator by sending indicator output demand signals to the combination meter assembly using CAN communication.
  2. The cruise control indicator illuminates when the cruise control system has been turned on using the ON-OFF switch. If a malfunction is detected, the cruise control indicator goes out and a warning message is displayed.
  3. The cruise control indicator circuit uses CAN communication. If the cruise control indicator is not functioning correctly, check for CAN communication DTCs before troubleshooting this circuit.

WIRING DIAGRAM


E230248E42


E230248E43


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (METER DISPLAY 1)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Select the following menu items: Body / Combination Meter / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Combination Meter 
    Tester Display
    Measurement Item
    Control Range
    Diagnostic Note
    Meter Display 1
    Multi-information display
    OFF or All
    -

    Result:
    Result
    Proceed to
    The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. (for 2AR-FE, 2GR-FE)
    A
    The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. (for 6AR-FSE)
    B
    The multi-information display in the combination meter assembly does not turn on or off according to the operation of the Active Test.
    C



B
Go to step 3

C
GO TO METER / GAUGE SYSTEM (Click here)
A


2.READ VALUE USING GTS (CCS INDICATOR M-CPU)
  1. Enter the following menus: Powertrain / Cruise Control / Data List.

  1. Read the Data List according to the display on the GTS.

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    CCS Indicator M-CPU
    Cruise control indicator illumination signal (Main-CPU) / ON or OFF
    ON: Cruise control indicator illuminated
    OFF: Cruise control indicator not on
    -

    Result:
    Result
    Proceed to
    The cruise control indicator illuminates and turns off according to the operation of the cruise control main switch (ON-OFF switch).
    A
    The cruise control indicator does not illuminate but the Data List item CCS Indicator M-CPU changes according to the operation of the cruise control main switch (ON-OFF switch).
    B
    The cruise control indicator does not illuminate and the Data List item CCS Indicator M-CPU does not change according to the operation of the cruise control main switch (ON-OFF switch) (for 2AR-FE).
    C
    The cruise control indicator does not illuminate and the Data List item CCS Indicator M-CPU does not change according to the operation of the cruise control main switch (ON-OFF switch) (for 2GR-FE).
    D



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.READ VALUE USING GTS (CRUISE INDICATOR)
  1. Enter the following menus: Powertrain / Cruise Control / Data List.

  1. Read the Data List according to the display on the GTS.

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Cruise Indicator
    Cruise control indicator signal / ON or OFF
    ON: Cruise control indicator turns on
    OFF: Cruise control indicator turns off
    -

    Result:
    Result
    Proceed to
    The cruise control indicator illuminates and turns off according to the operation of the cruise control main switch (ON-OFF switch).
    A
    The cruise control indicator does not illuminate but the Data List item Cruise Indicator changes according to the operation of the cruise control main switch (ON-OFF switch).
    B
    The cruise control indicator does not illuminate and the Data List item Cruise Indicator does not change according to the operation of the cruise control main switch (ON-OFF switch).
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE ECM (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)