Home › Engine / Hybrid System ยท CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST (for 2AR-FE, 2GR-FE)

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Select the following menu items: Powertrain / Cruise Control / Data List.

  5. Read the Data List according to the display on the GTS.

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    CCS Vehicle Spd
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual vehicle speed
    -
    CCS Mem Vehicle Spd
    Stored vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Stored vehicle speed
    -
    Throttle Opening Angle
    Required throttle opening angle / min.: 0°, max.: 124.50°
    Actual required throttle opening angle
    -
    Cruise Control
    Cruise control system active condition / ON or OFF
    ON: Cruise control activated
    OFF: Cruise control deactivated
    -
    Main SW M-CPU
    Cruise control switch signal (Main-CPU) / ON or OFF
    ON: Cruise control switch (ON-OFF button) pushed
    OFF: Cruise control switch (ON-OFF button) released
    -
    CCS Ready M-CPU
    Cruise control system standby condition (Main-CPU) / ON or OFF
    Each time cruise control switch (ON-OFF button) is pushed, ON/OFF changes
    -
    CCS Indicator M-CPU
    Cruise control indicator illumination signal (Main-CPU) / ON or OFF
    ON: Cruise control indicator illuminated
    OFF: Cruise control indicator not on
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    -/SET switch signal / ON or OFF
    ON: -/SET switch on
    OFF: -/SET switch off
    -
    RES/ACC Switch
    +/RES switch signal / ON or OFF
    ON: +/RES switch on
    OFF: +/RES switch off
    -
    Stp Light SW M-CPU
    Stop light switch signal (Main-CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Cruise Operation Status
    Transmission range sensor signal / ON or OFF
    ON: Shift lever in D or S
    OFF: Shift lever not in D or S
    -
    Brake Cancel Switch
    Brake cancel signal / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

    HINT:
    1. If any DTCs are output, the value for a measurement item may be incorrect.
    1. If any DTCs are output, perform troubleshooting accordingly. After repair, confirm relevant values using Data List.


READ DATA LIST (for 6AR-FSE)

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Select the following menu items: Powertrain / Cruise Control / Data List.

  5. Read the Data List according to the display on the GTS.

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Cruise Vehicle Speed
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph)
    Actual vehicle speed
    -
    Cruise Memory Vehicle Speed
    Stored vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph)
    Actual stored vehicle speed
    -
    Acceleration Continuation Decision
    Acceleration continuation decision condition / ON or OFF
    ON: Acceleration continuing
    OFF: Acceleration not continuing
    -
    Cruise Control Permission Condition
    Cruise control permission condition / ON or OFF
    ON: Cruise control permitted
    OFF: Cruise control prohibited
    -
    Cruise Control Condition
    Cruise control system condition / No Control/Constant Speed Control Mode - Ready
    No Control: Cruise control system not operating
    Constant Speed Control Mode - Ready: Constant speed control mode on standby
    -
    Cruise Control Mode
    Cruise control mode condition / No Control/Constant Speed Control Mode
    No Control: Cruise control mode not operating
    Constant Speed Control Mode: Constant speed control mode operating
    -
    Cruise Request Gear Position
    Shift request from ECM / None or 255 Gear
    Shift request from cruise control displayed
    -
    Cruise Acceleration and Deceleration Operation Condition
    Cruise acceleration and deceleration operation condition / No Control/Constant Speed Control Mode - Standby/Constant Speed Control Mode - RES SW Control/ Constant Speed Control Mode - COAST SW Control/ Vehicle Distance Control Mode - Acceleration Operation
    No Control: Cruise acceleration or deceleration not operating
    Constant Speed Control Mode - Standby: Cruise acceleration or deceleration operation on standby
    Constant Speed Control Mode - RES SW Control: During resume operation
    Constant Speed Control Mode - COAST SW Control: During acceleration operation
    Vehicle Distance Control Mode - Acceleration Operation: During deceleration operation
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    -SET Switch
    -/SET switch signal / ON or OFF
    ON: -/SET switch on
    OFF: -/SET switch off
    -
    +RES Switch
    +/RES switch signal / ON or OFF
    ON: +/RES switch on
    OFF: +/RES switch off
    -
    Cruise Ready Main-CPU
    Cruise control system standby condition (Main-CPU) / ON or OFF
    ON: Cruise control main switch (Main-CPU) SET
    OFF: Cruise control main switch (Main-CPU) UNSET
    -
    Cruise Ready Sub-CPU
    Cruise control system standby condition (Sub-CPU) / ON or OFF
    ON: Cruise control main switch (Sub-CPU) SET
    OFF: Cruise control main switch (Sub-CPU) UNSET
    -
    MODE Change Switch
    MODE switch signal / ON or OFF
    -
    Unused
    Accelerator Pedal
    Condition of the accelerator pedal during cruising / ON or OFF
    ON: Accelerator pedal depressed
    OFF: Accelerator pedal released
    -
    Cruise Brake Cancel Switch
    Cruise control system active condition / ON or OFF
    ON: Cruise control activated
    OFF: Cruise control deactivated
    -
    Stop Light Switch Main-CPU
    Stop light switch signal (Main-CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Stop Light Switch Sub-CPU
    Stop light switch signal (Sub-CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Request Automatic Cancel
    Whether there is an automatic cancel request / ON or OFF
    ON: Automatic cancel request exists
    OFF: Automatic cancel request does not exist
    -
    Cruise Brake Control Decision
    Cruise brake control decision / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Cruise Indicator
    Cruise control indicator signal / ON or OFF
    ON: Cruise control indicator turned on
    OFF: Cruise control indicator turned off
    -
    Gradient of Road Surface
    Gradient of road surface condition / -32.76 to 32.76 m/s2
    Current value displayed
    -

    HINT:
    1. If any DTCs are output, the value for a measurement item may be incorrect.
    1. If any DTCs are output, perform troubleshooting accordingly. After repair, confirm relevant values using Data List.


PERFORM ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Select the following menu items: Body / Combination Meter / Active Test.

  5. Perform the Active Test according to the display on the GTS.

    HINT:
    The ignition switch must be turned on to proceed with the Active Test using the GTS.


    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Meter Display 1
    Multi-information display
    OFF or All
    -