ENGINE UNIT > DISASSEMBLY |
| 1. REMOVE OIL FILLER CAP SUB-ASSEMBLY |
Remove the oil filler cap sub-assembly and oil filler gasket.
| 2. REMOVE SPARK PLUG |
![]() |
Remove the 6 spark plugs.
| 3. REMOVE OIL PAN DRAIN PLUG |
![]() |
Remove the oil pan drain plug and oil pan drain plug gasket.
| 4. REMOVE VENTILATION VALVE SUB-ASSEMBLY |
![]() |
Remove the ventilation valve sub-assembly.
| 5. REMOVE VVT SENSOR |
Disconnect the 4 sensor connectors.
![]() |
Remove the 4 bolts and 4 sensors.
| *a | for Bank 1 |
| *b | for Bank 2 |
| *c | for Intake Side |
| *d | for Exhaust Side |
| 6. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
Disconnect the 4 oil control valve connectors.
![]() |
Remove the 4 bolts and 4 oil control valves.
| *a | for Intake Side |
| *b | for Exhaust Side |
| *c | for Bank 2 |
| *d | for Bank 1 |
![]() |
Remove the O-ring from each oil control valve.
| *1 | O-ring |
| 7. REMOVE CRANK POSITION SENSOR |
![]() |
Disconnect the crank position sensor connector.
Remove the bolt and crank position sensor.
| 8. REMOVE NO. 1 OIL PIPE |
![]() |
Remove the 2 oil pipe unions, gaskets and No. 1 oil pipe.
| *1 | Oil Pipe Union |
Remove the oil control valve filter LH and gaskets.
| 9. REMOVE OIL PIPE |
![]() |
Remove the bolt.
| *1 | Oil Pipe Union |
| *2 | Bolt |
Remove the 2 oil pipe unions and oil pipe.
Remove the oil control valve filter RH and gaskets.
| 10. REMOVE TAPER SCREW PLUG |
![]() |
Remove the taper screw plug from the cylinder block.
| 11. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
for Bank 1:
Remove the cylinder block water drain cock sub-assembly from the cylinder block.
![]() |
Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.
| *a | for Bank 1 |
| *b | for Bank 2 |
for Bank 2:
Remove the cylinder block water drain cock sub-assembly from the cylinder block.
Remove the cylinder block water drain cock plugs from the cylinder block water drain cock sub-assembly.
| 12. REMOVE OIL FILTER CAP ASSEMBLY |
![]() |
Connect the hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
| *1 | Pipe |
| *2 | Hose |
![]() |
Remove the oil filter drain plug from the oil filter cap.
![]() |
Insert the pipe with the hose into the oil filter cap.
| *1 | Cap |
| *2 | O-ring |
| *3 | Pipe |
![]() |
Make sure that oil is completely drained, and remove the pipe and O-ring.
![]() |
Using SST, remove the oil filter cap.
![]() |
Remove the oil filter element and O-ring from the oil filter cap.
| *1 | Oil Filter Element |
| *2 | Oil Filter Cap |
| *3 | O-ring |
| 13. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, loosen the crankshaft pulley bolt.
| *a | Hold |
![]() | Turn |
![]() |
Using SST, remove the crankshaft pulley bolt and crankshaft pulley.
| *a | Hold |
![]() | Turn |
![]() |
Remove the pulley set key from the crankshaft.
| 14. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE |
![]() |
Remove the bolt and engine oil level dipstick guide.
![]() |
Remove the O-ring.
| 15. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH |
![]() |
Remove the 6 bolts and No. 1 front engine mounting bracket LH.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts.
| 16. REMOVE WATER INLET HOUSING |
![]() |
Remove the 2 nuts, water inlet and thermostat.
Remove the gasket.
Remove the 2 stud bolts.
Separate the No. 1 water by-pass hose from the water inlet housing.
![]() |
Remove the drain cock plug.
| *1 | Nut |
| *2 | Bolt |
Remove the drain cock assembly.
Remove the 2 bolts, nut, and water inlet housing.
![]() |
Remove the 2 O-rings.
| 17. REMOVE WATER OUTLET |
![]() |
Remove the 2 bolts, 4 nuts and water outlet.
| *1 | Nut |
| *2 | Bolt |
![]() |
Remove the 2 gaskets and O-ring.
| 18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.
![]() |
Remove the 3 gaskets.
| 19. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH |
![]() |
Remove the 12 bolts, seal washer, cylinder head cover sub-assembly LH and No. 2 cylinder head cover gasket.
| *1 | Baffle Plate |
![]() |
Remove the 3 gaskets.
| 20. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 16 bolts and 2 nuts.
| *1 | Nut |
![]() |
Insert the blade of the oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.
Using an E6 "TORX" socket wrench, remove the 2 stud bolts.
| 21. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() |
Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.
| *1 | Bolt |
| *2 | Nut |
Using an E6 "TORX" socket wrench, remove the 2 stud bolts.
| 22. REMOVE OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 16 bolts and 2 nuts.
| *A | Type A |
| *B | Type B |
| *a | Nut |
![]() |
Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block with a screwdriver.
| *1 | Protective Tape |
![]() |
Remove the 2 O-rings.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts.
| 23. REMOVE NO. 1 OIL PAN BAFFLE PLATE |
![]() |
Remove the 7 bolts and No. 1 oil pan baffle plate.
| 24. REMOVE ENGINE REAR OIL SEAL RETAINER |
![]() |
Remove the 6 bolts.
![]() |
Using a screwdriver, pry out the engine rear oil seal retainer.
| *1 | Protective Tape |
![]() | Pry |
| 25. REMOVE ENGINE REAR OIL SEAL |
![]() |
Place the engine rear oil seal retainer on wooden blocks.
| *1 | Protective Tape |
| *2 | Wooden Block |
Using a screwdriver and a hammer, tap out the engine rear oil seal.
| 26. REMOVE ENGINE WATER PUMP ASSEMBLY |
![]() |
Remove the 16 bolts, engine water pump assembly and water pump gasket.
| 27. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Remove the 15 bolts and 2 nuts as shown in the illustration.
| *1 | Nut |
![]() |
Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly or cylinder block with a screwdriver.
| *1 | Protective Tape |
Remove the 4 bolts, timing chain cover plate and timing chain cover plate gasket.
![]() |
Remove the gasket.
| 28. REMOVE TIMING CHAIN CASE OIL SEAL |
![]() |
Using a screwdriver and wooden block, pry out the oil seal.
| *1 | Protective Tape |
| *2 | Wooden Block |
| 29. SET NO. 1 CYLINDER TO TDC/COMPRESSION |
Temporarily tighten the pulley set bolt.
![]() |
Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).
| *1 | Sensor Plate |
| *a | Center Line |
| *b | Timing Mark |
![]() |
Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are aligned with the timing marks of the camshaft bearing caps as shown in the illustration.
| *a | Timing Mark |
| 30. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.
| *1 | Plunger |
| *2 | Stopper Plate |
| *3 | Pin |
Move the stopper plate downward to set the lock, and insert a pin of 1.27 mm diameter (0.0500 in.) into the stopper plate hole.
![]() |
Remove the 2 bolts and No. 1 chain tensioner assembly.
| 31. REMOVE CHAIN TENSIONER SLIPPER |
Remove the chain tensioner slipper.
| 32. REMOVE CHAIN SUB-ASSEMBLY |
![]() |
Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.
| *1 | Sensor Plate |
| *a | Center Line |
| *b | Timing Mark |
Remove the pulley set bolt.
![]() |
Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.
![]() |
Turn the camshaft timing gear assembly on bank 1 clockwise (approximately 60°) and set it as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.
| *a | for Bank 1 |
Remove the chain sub-assembly.
| 33. REMOVE IDLE SPROCKET ASSEMBLY |
![]() |
Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.
| 34. REMOVE NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Remove the 2 bolts and No. 1 chain vibration damper.
| 35. REMOVE NO. 2 CHAIN VIBRATION DAMPER |
Remove the 2 No. 2 chain vibration dampers.
| 36. REMOVE CRANKSHAFT TIMING SPROCKET |
![]() |
Remove the crankshaft timing sprocket from the crankshaft.
Remove the 2 keys from the crankshaft.
| 37. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1) |
![]() |
While raising the No. 2 chain tensioner assembly, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold the No. 2 chain tensioner assembly.
| *1 | Pin |
| *2 | Plunger |
| *a | Push |
![]() |
Using SST to hold the hexagonal portion of each camshaft, loosen the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Remove the 2 bolts and the camshaft timing gear assembly together with the No. 2 chain.
| 38. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Remove the bolt and No. 2 chain tensioner assembly.
| 39. REMOVE CAMSHAFT BEARING CAP (for Bank 1) |
![]() |
Check that the camshafts are positioned as shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
![]() |
Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.
![]() |
Uniformly loosen and remove the 12 bearing cap bolts in several steps and in the sequence shown in the illustration.
Remove the 5 camshaft bearing caps.
| 40. REMOVE CAMSHAFT |
Remove the camshaft.
| 41. REMOVE NO. 2 CAMSHAFT |
Remove the No. 2 camshaft.
| 42. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH |
![]() |
Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.
| *1 | Protective Tape |
| 43. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2) |
![]() |
While pushing down the No. 3 chain tensioner assembly, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold the No. 3 chain tensioner assembly.
| *1 | Pin |
| *2 | Plunger |
| *a | Push |
![]() |
Using SST to hold the hexagonal portion of each camshaft, loosen the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Remove the 2 bolts and the camshaft timing gear together with the No. 2 chain.
| 44. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Remove the bolt and No. 3 chain tensioner assembly.
| 45. REMOVE CAMSHAFT BEARING CAP (for Bank 2) |
![]() |
Check that the camshafts are positioned as shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
![]() |
Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.
![]() |
Uniformly loosen and remove the 13 bearing cap bolts in several steps and in the sequence shown in the illustration.
Remove the 5 camshaft bearing caps.
| 46. REMOVE NO. 3 CAMSHAFT |
Remove the No. 3 camshaft.
| 47. REMOVE NO. 4 CAMSHAFT |
Remove the No. 4 camshaft.
| 48. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH |
![]() |
Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.
| *1 | Protective Tape |
| 49. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
Remove the 24 valve rocker arms.
| 50. REMOVE VALVE LASH ADJUSTER ASSEMBLY |
Remove the 24 valve lash adjuster assemblies from the cylinder head.
| 51. REMOVE VALVE STEM CAP |
Remove the valve stem caps from the cylinder heads.
| 52. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH |
![]() |
Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.
Remove the cylinder head sub-assembly RH.
| 53. REMOVE CYLINDER HEAD GASKET RH |
Remove the cylinder head gasket RH.
| 54. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH |
![]() |
Uniformly loosen and remove the 2 cylinder head set bolts in several steps and in the sequence shown in the illustration.
![]() |
Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.
Remove the cylinder head sub-assembly LH.
| 55. REMOVE CYLINDER HEAD GASKET LH |
Remove the cylinder head gasket LH.
| 56. REMOVE WATER INLET PIPE |
Remove the 2 clamps and separate the No. 1 water by-pass hose.
![]() |
Remove the 2 bolts and water inlet pipe.