Home › Engine / Hybrid System ยท 2GR-FE › ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REASSEMBLY

for Preparation Click here


HINT:
Perform "Inspection After Repair" after replacing the cylinder head (Click here).



1. INSTALL SPARK PLUG TUBE

HINT:
When using a new cylinder head, the spark plug tubes must be replaced.



    A211988E01
  1. Apply adhesive onto the shaded area of a new spark plug tube.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

    Standard application width:
    1.0 to 3.0 mm (0.0394 to 0.118 in.)

    NOTICE:
    1. Install the spark plug tube within 3 minutes after applying adhesive.
    2. Be careful not to deform the spark plug tube.
    3. Be careful not to expose the seal to engine oil for at least 1 hour after installing it.



    A213713E12
  1. Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.
    Text in Illustration 
    *a
    Cylinder Head Top Surface

    Standard protrusion height:
    72.9 mm (2.87 in.)

    NOTICE:
    To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.



2. INSTALL NO. 1 STRAIGHT SCREW PLUG


    A129718E12
  1. Using a 10 mm hexagon wrench, install 4 new gaskets and the 4 No. 1 straight screw plugs.
    Text in Illustration 
    *a
    Bank 1
    *b
    Bank 2

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



3. INSTALL NO. 2 STRAIGHT SCREW PLUG


    A187883E01
  1. Using a 14 mm hexagon wrench, install 2 new gaskets and the 2 No. 2 straight screw plugs.
    Text in Illustration 
    *a
    Bank 1
    *b
    Bank 2

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }



4. INSTALL VALVE SPRING SEAT
  1. Install the valve spring seats to the cylinder head.



5. INSTALL VALVE STEM OIL SEAL


    A094934E17
  1. Apply a light coat of engine oil to new valve stem oil seals.
    Text in Illustration 
    *a
    Gray
    (Intake Side)
    *b
    Black
    (Exhaust Side)

    NOTICE:
    Pay attention when installing the intake and exhaust valve stem oil seals. For example, installing the intake valve stem oil seal into the exhaust side or installing the exhaust valve stem oil seal to the intake side can cause installation problems later.

    HINT:
    The intake valve oil seals are gray and the exhaust valve oil seals are black.



    A124592E06
  1. Using SST, push in the oil seals.
    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT

    SST
    09201-41020  

    NOTICE:
    Failure to use SST will cause the seal to be damaged or improperly seated.



6. INSTALL EXHAUST VALVE


    A094936E27
  1. Apply a sufficient coat of engine oil to the tip area of the exhaust valve shown in the illustration.
    Text in Illustration 
    *a
    30 mm (1.18 in.) or more

  1. Install the exhaust valve, inner compression spring and valve spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to the original locations.



    A333218E01
  1. Using SST, compress the inner compression spring and install the 2 valve spring retainer locks.

    SST
    09202-70020  
    09202-00020  



    A333603
  1. Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the retainer.



7. INSTALL INTAKE VALVE


    A094935E29
  1. Apply a sufficient coat of engine oil to the tip area of the intake valve shown in the illustration.
    Text in Illustration 
    *a
    30 mm (1.18 in.) or more

  1. Install the intake valve, inner compression spring and valve spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to their original locations.



    A333217E01
  1. Using SST, compress the inner compression spring and install the 2 valve spring retainer locks.

    SST
    09202-70020  
    09202-00020  



    A333602
  1. Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the retainer.



8. INSTALL VALVE STEM CAP
  1. Apply a light coat of engine oil to the valve stem caps.

  1. Install the valve stem caps on the valves.