Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > TERMINALS OF ECU

for Preparation Click here



CHECK FRONT POWER SEAT SWITCH LH (W/ MEMORY)


  1. Disconnect the e11 and e12 front power seat switch LH (w/ Memory) connectors.


    B219506E57

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Terminal Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    e11-2 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    e11-7 (+B) - e11-2 (GND)
    W - W-B
    Power source
    Always
    11 to 14 V
    e12-12 (SYSB) - e11-2 (GND)
    P - W-B
    System power source
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the e11 and e12 front power seat switch LH (w/ Memory) connectors.

  4. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    e11-6 (+B2) - e11-1 (GND2)
    SB - W-B
    Lumbar support adjuster power source
    Always
    11 to 14 V
    e11-1 (GND2) - Body ground
    W-B - Body ground
    Lumbar support adjuster ground
    Always
    Below 1 Ω
    e11-3 (SLD+) - e11-2 (GND)
    L - W-B
    Slide motor signal (forward)
    Slide switch off
    Below 1 V
    Slide switch on (Forward)
    11 to 14 V
    e11-4 (SLD-) - e11-2 (GND)
    GR - W-B
    Slide motor signal (rearward)
    Slide switch off
    Below 1 V
    Slide switch on (Rearward)
    11 to 14 V
    e11-5 (FRV-) - e11-2 (GND)
    R - W-B
    Front vertical motor signal (downward)
    Front vertical switch off
    Below 1 V
    Front vertical switch on (Downward)
    11 to 14 V
    e11-8 (FRV+) - e11-2 (GND)
    B - W-B
    Front vertical motor signal (upward)
    Front vertical switch off
    Below 1 V
    Front vertical switch on (Upward)
    11 to 14 V
    e11-9 (RCL+) - e11-2 (GND)
    P - W-B
    Reclining motor signal (forward)
    Reclining switch off
    Below 1 V
    Reclining switch on (Forward)
    11 to 14 V
    e11-11 (RCL-) - e11-2 (GND)
    LG - W-B
    Reclining motor signal (rearward)
    Reclining switch off
    Below 1 V
    Reclining switch on (Rearward)
    11 to 14 V
    e11-10 (LFT+) - e11-2 (GND)
    V - W-B
    Lifter motor signal (upward)
    Lifter switch off
    Below 1 V
    Lifter switch on (Upward)
    11 to 14 V
    e11-12 (LFT-) - e11-2 (GND)
    G - W-B
    Lifter motor signal (downward)
    Lifter switch off
    Below 1 V
    Lifter switch on (Downward)
    11 to 14 V
    e12-1 (SGND) - e11-2 (GND)
    BR - W-B
    Position sensor round
    Always
    Below 1 Ω
    e12-3 (SSFV) - e12-1 (SGND)
    R - BR
    Front vertical position signal
    Front vertical function operating
    4.5 to 4.8 V
    e12-4 (SSRL) - e12-1 (SGND)
    P - BR
    Lifter position signal
    Lifter function operating
    4.5 to 4.8 V
    e12-5 (SSRS) - e12-1 (SGND)
    G- BR
    Slide position signal
    Slide function operating
    4.5 to 4.8 V
    e12-11 (SSRR) - e12-1 (SGND)
    V - BR
    Reclining position signal
    Reclining function operating
    4.5 to 4.8 V
    If the result is not as specified, the front power seat switch LH (w/ Memory) may have a malfunction.


CHECK OUTER MIRROR CONTROL ECU ASSEMBLY LH


  1. Disconnect the K12 outer mirror control ECU assembly LH connector.


    B343031E07

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K12-7 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    K12-14 (BDR) - K12-7 (GND)
    GR - W-B
    Power source
    Always
    11 to 14 V
    K12-5 (SIG) - K12-7 (GND)
    GR - W-B
    Power source (IG)
    Always
    Below 1 V
    Engine switch on (IG)
    11 to 14 V
    K12-6 (CPUB) - K12-7 (GND)
    W - W-B
    Power source
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the K12 outer mirror control ECU assembly LH connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K12-3 (M2) - K12-4 (MSWE)
    G - B
    M2 switch signal for seat memory switch
    M2 switch on
    Below 1 V
    M2 switch off
    11 to 14 V
    K12-2 (M1) - K12-4 (MSWE)
    R - B
    M1 switch signal for seat memory switch
    M1 switch on
    Below 1 V
    M1 switch off
    11 to 14 V
    K12-1 (MM) - K12-4 (MSWE)
    P - B
    SET switch signal for seat memory switch
    SET switch on
    Below 1 V
    SET switch off
    11 to 14 V
    If the result is not as specified, the outer mirror control ECU assembly LH may have a malfunction.


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY



  1. B282096E51


    Text in Illustration 
    *A
    Main body ECU (multiplex network body ECU) with 3 connectors
    -
    -
    *1
    Main body ECU (multiplex network body ECU)
    *2
    3 connectors

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-30 (BECU) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    MB-31 (ALTB) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    Ignition power supply (IG signal)
    Engine switch on (IG) → off
    11 to 14 V → Below 1 V
    MB-29 (ACC) - Body ground
    -
    Ignition power supply (ACC signal)
    Engine switch on (ACC) → off
    11 to 14 V → Below 1 V
    MB-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    I12-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    MB-2 (FLCY) - Body ground
    -
    Front door courtesy light switch LH input
    Front door LH closed (OFF) → open (ON)
    10 kΩ or higher → Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.