SLIDING ROOF SYSTEM > Sliding Roof does not Move by Operating Sliding Roof Control Switch |

| 1.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Sliding Roof / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Open Switch | OPEN switch signal/ON or OFF | ON: OPEN switch pressed OFF: OPEN switch not pressed | - |
| Close Switch | CLOSE switch signal/ON or OFF | ON: CLOSE switch pressed OFF: CLOSE switch not pressed | - |
| Up Switch | UP switch signal/ON or OFF | ON: UP switch pressed OFF: UP switch not pressed | - |
| Down Switch | DOWN switch signal/ON or OFF | ON: DOWN switch pressed OFF: DOWN switch not pressed | - |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY AND BODY GROUND) |
Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S4-8 (B) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S4-12 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 3.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY) |
![]() |
Remove the sliding roof switch (roof console box assembly) (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 5 (UP) - 1 (GND) | UP switch is pressed | Below 1 Ω |
| 5 (UP) - 1 (GND) | UP switch is not pressed | 10 kΩ or higher |
| 4 (DOWN) - 1 (GND) | DOWN switch is pressed | Below 1 Ω |
| 4 (DOWN) - 1 (GND) | DOWN switch is not pressed | 10 kΩ or higher |
| 3 (OPN) - 1 (GND) | OPEN switch is pressed | Below 1 Ω |
| 3 (OPN) - 1 (GND) | OPEN switch is not pressed | 10 kΩ or higher |
| 2 (CLS) - 1 (GND) | CLOSE switch is pressed | Below 1 Ω |
| 2 (CLS) - 1 (GND) | CLOSE switch is not pressed | 10 kΩ or higher |
| *a | Component without harness connected (Sliding Roof Switch (Roof Console Box Assembly)) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH AND BODY GROUND) |
Disconnect the S7*1 or S14*2 sliding roof switch (roof console box assembly) connector.
Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S4-5 (CLS) - S7-2 (CLS)*1 S4-5 (CLS) - S14-2 (CLS)*2 | Always | Below 1 Ω |
| S4-5 (CLS) - Body ground | Always | 10 kΩ or higher |
| S4-7 (OPN) - S7-3 (OPN)*1 S4-7 (OPN) - S14-3 (OPN)*2 | Always | Below 1 Ω |
| S4-7 (OPN) - Body ground | Always | 10 kΩ or higher |
| S4-6 (DWN) - S7-4 (DOWN)*1 S4-6 (DWN) - S14-4 (DOWN)*2 | Always | Below 1 Ω |
| S4-6 (DWN) - Body ground | Always | 10 kΩ or higher |
| S4-4 (UP) - S7-5 (UP)*1 S4-4 (UP) - S14-5 (UP)*2 | Always | Below 1 Ω |
| S4-4 (UP) - Body ground | Always | 10 kΩ or higher |
| S7-1 (GND) - Body ground*1 S14-1 (GND) - Body ground*2 | Always | Below 1 Ω |
| S4-12 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||