Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System)

ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System) > Security Indicator Light Does not Blink

for Preparation Click here


DESCRIPTION

  1. The transponder key ECU assembly blinks the security indicator light when the immobiliser is set (no key is in the ignition key cylinder).
  2. The main body ECU (multiplex network body ECU) blinks the security indicator light when the theft deterrent system is in the arming preparation state or alarm sounding state.

WIRING DIAGRAM


B271008E03


INSPECTION PROCEDURE

NOTICE:
If the transponder key ECU assembly is replaced, refer to Service Bulletin.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Immobiliser or Main Body / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    Immobiliser (Transponder Key ECU Assembly) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Indicator
    Security indicator light
    ON/OFF
    -

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Indicator
    Security indicator light
    ON/OFF
    -

    Result:
    Result
    Proceed to
    Security indicator light operation is normal when performing the "Main Body" and "Immobiliser" Active Test
    A
    1. Security indicator light operation is not normal when performing the "Immobiliser" Active Test
    2. Security indicator light operation is normal when performing the "Main Body" Active Test
    B
    1. Security indicator light operation is normal when performing the "Immobiliser" Active Test
    2. Security indicator light operation is not normal when performing the "Main Body" Active Test
    C
    Security indicator light operation is not normal when performing the "Main Body" and "Immobiliser" Active Test
    D



B
Go to step 3

C
Go to step 4

D
Go to step 5
A


2.CHECK SECURITY INDICATOR LIGHT OPERATION
  1. When the immobiliser is set, check that the security indicator light blinks.*1

    OK:
    The security indicator light blinks normally.

  1. When the theft deterrent system is in the arming preparation state, check that the security indicator light on (Click here).*2

    OK:
    The security indicator light is on normally.

    Result:
    Result
    Proceed to
    Both *1 and *2 are OK
    A
    *1 is NG (*2 is OK)
    B
    *2 is NG (*1 is OK)
    C
    Both *1 and *2 are NG
    D



B
REPLACE TRANSPONDER KEY ECU ASSEMBLY

C
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

D
REPLACE SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) - TRANSPONDER KEY ECU ASSEMBLY)
  1. Disconnect the security indicator light (heater control switch board) connector.

  1. Disconnect the transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I19-8 (IND) - I56-1 (LP)
    Always
    Below 1 Ω
    I19-8 (IND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY 

4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
  1. Disconnect the security indicator light (heater control switch board) connector.

  1. Disconnect the main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I12-22 (IND) - I56-1 (LP)
    Always
    Below 1 Ω
    I12-22 (IND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

5.CHECK HARNESS AND CONNECTOR
  1. Disconnect the security indicator light (heater control switch board) connector.

  1. Disconnect transponder key ECU assembly connector.

  1. Disconnect the main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I19-8 (IND) - I56-1 (LP)
    Always
    Below 1 Ω
    I12-22 (IND) - I56-1 (LP)
    Always
    Below 1 Ω
    I56-1 (LP) - Body ground
    Always
    10 kΩ or higher
    I56-6 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD)
  1. Temporarily replace the security indicator light (heater control switch board) with a new or known good one (Click here).

  1. When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

    OK:
    Security indicator light blinks.



NG
Go to step 7
OK

END (HEATER CONTROL SWITCH BOARD WAS DEFECTIVE) 

7.REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Temporarily replace the transponder key ECU assembly with a new or known good one.

    HINT:
    Refer to Service Bulletin.

  1. When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

    OK:
    Security indicator light blinks.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)