Home › Drivetrain · U761E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P070513    Transmission Range Sensor "A" Circuit Open

DTC    P070562    Transmission Range Sensor "A" Signal Compare Failure

for Preparation Click here


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends a signal to the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P070513
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
  1. The engine switch is on (IG) and battery voltage is 10.5 V or more.
  2. All of the following signals are OFF simultaneously:
    1. P input signal
    2. R input signal
    3. N input signal
    4. D input signal
    5. NSW input signal
  3. 60 seconds
  4. 2-trip detection logic
  1. Wire harness or connector
  2. Open in park/neutral position switch assembly circuit
  3. Park/neutral position switch assembly
  4. ECM
P070562
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
  1. The engine switch is on (IG) and battery voltage is 10.5 V or more.
  2. 2 or more of the following signals are ON simultaneously:
    1. (NSW, P or N) input signal
    2. R input signal
    3. D input signal
  3. 2 seconds
  4. 2-trip detection logic
  1. Wire harness or connector
  2. Short in park/neutral position switch assembly circuit
  3. Park/neutral position switch assembly
  4. ECM

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch assembly or the wire harness in the park/neutral position switch assembly circuit.
The park/neutral position switch assembly detects the shift lever position and sends a signal to the ECM.
For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, N, R, D or S). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously and will illuminate the MIL and store a DTC.

WIRING DIAGRAM


C319065E01


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following procedure.
  2. Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

HINT:
  1. Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
  2. After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
    1. Turn the engine switch on (IG).
    2. Wait with the shift lever in each position (P, R, N and D) for 60 seconds or more each.
    3. Turn the engine switch off.
    4. Perform steps (a) through (c) again.
    5. Check for DTCs again (Click here).


DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the engine switch off.
  3. Connect the GTS to the DLC3.
  4. Turn the engine switch on (IG).
  5. Turn the GTS on.
  6. Enter the following menus: Powertrain / Transmission / Data List.
  7. Read the Data List according to the display on the GTS.

    Transmission 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW
    Park/neutral position switch status / ON or OFF
    1. ON: Shift lever is in P or N
    2. OFF: Shift lever is not in P or N
    When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
    Shift SW Status (P Range)
    Park/neutral position switch status / ON or OFF
    1. ON: Shift lever is in P
    2. OFF: Shift lever is not in P
    When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
    Shift SW Status (R Range)
    Park/neutral position switch status / ON or OFF
    1. ON: Shift lever is in R
    2. OFF: Shift lever is not in R
    When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
    Shift SW Status (N Range)
    Park/neutral position switch status / ON or OFF
    1. ON: Shift lever is in N
    2. OFF: Shift lever is not in N
    When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
    Shift SW Status (D Range)
    Park/neutral position switch status / ON or OFF
    1. ON: Shift lever is in D or S
    2. OFF: Shift lever is not in D or S
    When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
  1. Disconnect the E85 park/neutral position switch assembly connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E85-1 (RB) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)
  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E85-4 (B) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 5
OK


3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C275091E01
  1. Disconnect the E85 park/neutral position switch assembly connector.
    Text in Illustration 
    *a
    Component without harness connected
    (Park/Neutral Position Switch Assembly)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (B) - 9 (L)
    Shift lever in P or N
    Below 1 Ω
    Shift lever not in P or N
    10 kΩ or higher
    1 (RB) - 3 (PL)
    Shift lever in P
    Below 1 Ω
    Shift lever not in P
    10 kΩ or higher
    1 (RB) - 8 (NL)
    Shift lever in N
    Below 1 Ω
    Shift lever not in N
    10 kΩ or higher
    1 (RB) - 2 (RL)
    Shift lever in R
    Below 1 Ω
    Shift lever not in R
    10 kΩ or higher
    1 (RB) - 7 (DL)
    Shift lever in D, S, "+" or "-"
    Below 1 Ω
    Shift lever not in D, S, "+" or "-"
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
  1. Connect the E85 park/neutral position switch assembly connector.

  1. Disconnect the E96 ECM connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E96-64 (P) - Body ground
    Shift lever in P
    11 to 14 V
    Shift lever not in P
    Below 1 V
    E96-65 (N) - Body ground
    Shift lever in N
    11 to 14 V
    Shift lever not in N
    Below 1 V
    E96-35 (R) - Body ground
    Shift lever in R
    11 to 14 V*
    Shift lever not in R
    Below 1 V
    E96-34 (D) - Body ground
    Shift lever in D, S, "+" or "-"
    11 to 14 V
    Shift lever not in D, S, "+" or "-"
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to the illumination of the back up lights.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
  1. Turn the engine switch off.

  1. Disconnect the A84 ECM connector.

  1. Disconnect the E85 park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E85-4 (B) - A84-57 (NSW)
    Always
    Below 1 Ω
    E85-4 (B) or A84-57 (NSW) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)