Home › Drivetrain · U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P2759    Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)

for Preparation Click here


DESCRIPTION

Refer to the system description for DTC P2757 .

DTC No.
DTC Detection Condition
Trouble Area
P2759
Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1-trip detection logic).
  1. Open or short in shift solenoid valve SLU circuit
  2. Shift solenoid valve SLU
  3. Wiring Harness Connector
  4. ECM

MONITOR DESCRIPTION

When an open or short in a shift solenoid valve (SLU) circuit is detected, the ECM determines there is a malfunction. The ECM will turn on the MIL and store this DTC.

WIRING DIAGRAM


C239277E02


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SLU CIRCUIT)


    C233488E02
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E26-7 (SLU+) - E26-6 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    E26-7 (SLU+) - Body ground and other terminals
    Always
    10 kΩ or higher
    E26-6 (SLU-) - Body ground and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
Go to step 2
OK

REPLACE ECM (Click here)  

2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
  1. Disconnect the harness connector from the wiring harness connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E26-7 (SLU+) - E8-14 (SLU+)
    Always
    Below 1 Ω
    E26-6 (SLU-) - E8-5 (SLU-)
    Always
    Below 1 Ω
    E26-7 (SLU+) or E8-14 (SLU+) - Body ground and other terminals
    Always
    10 kΩ or higher
    E26-6 (SLU-) or E8-5 (SLU-) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT TRANSMISSION WIRE (SLU)


    C133212E36
  1. Remove the wiring harness connector from the automatic transaxle.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-11 (SLU+) - A-5 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    A-11 (SLU+) - Body ground and other terminals
    Always
    10 kΩ or higher
    A-5 (SLU-) - Body ground and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 4
OK

REPLACE WIRING HARNESS CONNECTOR (Click here)  

4.INSPECT SHIFT SOLENOID VALVE SLU


    C201747E01
  1. Remove shift solenoid valve SLU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

    OK:
    Valve moves and makes an operating sound.

    Text in Illustration 
    *1
    Shift Solenoid Valve SLU



NG
REPLACE SHIFT SOLENOID VALVE SLU (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)