Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to +B (LHD Models)

for Preparation Click here


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.

Symptom
Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of DLC3.
  1. Short to +B in CAN main bus line
  2. Short to +B in CAN branch line
  3. AFS ECU*1
  4. ECM
  5. Main body ECU (Multiplex network body ECU)
  6. Combination meter assembly
  7. Brake actuator assembly
  8. Steering sensor
  9. Clearance warning ECU assembly*2
  10. Power steering ECU with motor assembly
  11. Airbag sensor assembly
  12. Air conditioning amplifier assembly
  13. Smart key ECU assembly (Certification ECU)*3
  14. Navigation receiver assembly*4
  15. Radio and display receiver assembly*5
  16. Network gateway ECU*6
  17. Inner rear view mirror assembly*7
  18. Telematics transceiver*8
  19. CAN No. 1 junction connector
  20. CAN No. 2 junction connector
*1: w/ AFS
*2: w/ Toyota Parking Assist-sensor System
*3: w/ Smart Entry and Start System
*4: for Navigation Receiver Type
*5: for Radio and Display Type
*6: w/ Network Gateway ECU
*7: w/ Automatic High Beam System
*8: w/ Telematics Transceiver

WIRING DIAGRAM


C244448E06


C370610E01


C311103E02


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON, wait at least 31 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.
  6. After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
  3. Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.

1.CHECK VEHICLE TYPE
  1. Check vehicle type.

    Result:
    Result
    Proceed to
    except TMMR Made
    A
    for TMMR Made
    B



B
Go to step 7
A


2.CHECK FOR SHORT TO +B IN CAN BUS LINE (DLC3 BRANCH LINE)
  1. Disconnect the cable from the negative (-) battery terminal.



    C241463E06
  1. Disconnect the DLC3 branch line connector (I96) from the CAN No. 1 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 1 Junction Connector)
    *b
    to DLC3

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C292403E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I39-14 (CANL) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3
OK


3.CHECK FOR SHORT TO +B IN CAN BUS LINE
  1. Reconnect the DLC3 branch line connector (I96) to the CAN No. 1 junction connector.



    C292403E02
  1. Disconnect the connectors (I94, I95, I97, I100, I102, I103, I104, I105, I106, I107, I111, I112 and I188) from the CAN No. 1 junction connector and CAN No. 2 junction connector one at a time.

    HINT:
    Disconnect the ECU and sensor connectors other than the DLC3 branch lines and CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.

    Text in Illustration 
    *1
    DLC3



  1. Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.


    C311104E02


    Text in Illustration 
    *A
    w/ Toyota Parking Assist-sensor System
    *B
    w/ Smart Entry and Start System
    *C
    for Navigation Receiver Type
    *D
    for Radio and Display Type
    *E
    w/ Network Gateway ECU
    *F
    w/ AFS
    *1
    Clearance Warning ECU Assembly
    *2
    Air Conditioning Amplifier Assembly
    *3
    ECM
    *4
    Brake Actuator Assembly
    *5
    Smart Key ECU Assembly (Certification ECU)
    *6
    Navigation Receiver Assembly
    *7
    Radio and Display Receiver Assembly
    *8
    Network Gateway ECU
    *9
    Combination Meter Assembly
    *10
    Power Steering ECU with Motor Assembly
    *11
    DLC3
    *12
    Airbag Sensor Assembly
    *13
    Steering Sensor
    *14
    Main Body ECU (Multiplex Network Body ECU)
    *15
    AFS ECU
    *16
    CAN No. 1 Junction Connector
    *17
    CAN No. 2 Junction Connector
    -
    -

    C241464E20


    Text in Illustration 
    *a
    Component without harness connected
    (CAN No. 1 Junction Connector)
    -
    -

    Wiring Color 
    CAN No. 1 Junction Connector Side
    Code
    Color (CANH Side)
    Color (CANL Side)
    AFS ECU*
    I112
    BE
    W
    Main body ECU (Multiplex network body ECU)
    I95
    P
    W
    Steering sensor
    I97
    V
    W
    Airbag sensor assembly
    I103
    Y
    W
    DLC3
    I96
    L
    W
    Power steering ECU with motor assembly
    I100
    G
    W
    Combination meter assembly
    I94
    R
    W
    CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector)
    I93
    B
    W
    *: w/ AFS

    C311106E01


    Text in Illustration 
    *a
    Component without harness connected
    (CAN No. 2 Junction Connector)
    -
    -

    Wiring Color 
    CAN No. 2 Junction Connector Side
    Code
    Color (CANH Side)
    Color (CANL Side)
    CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector)
    I101
    B
    W
    Air conditioning amplifier assembly
    I102
    V
    W
    ECM
    I104
    P
    W
    Smart key ECU assembly (Certification ECU)*1
    I106
    L
    W
    Clearance warning ECU assembly*2
    I111
    BE
    W
    Network Gateway ECU*3
    I188
    G
    W
    1. Navigation receiver assembly*4
    2. Radio and display receiver assembly*5
    I107
    R
    W
    Brake actuator assembly
    I105
    Y
    W
    *1: w/ Smart Entry and Start System
    *2: w/ Toyota Parking Assist-sensor System
    *3: w/ Network Gateway ECU
    *4: for Navigation Receiver Type
    *5: for Radio and Display Type

    NOTICE:
    Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to +B in 2 or more CAN bus lines.


    Result:

    Symptom
    Proceed to
    The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector. (There is a short to +B in the CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.)
    A
    The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector. (There is a short to +B in one of the areas that relate to one or more of the disconnected bus lines.)
    B

  1. When there is a short to +B in one or more of the bus lines that connect to an ECU or sensor:

    1. Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to +B). Check that the resistance shown on the tester is normal (6 kΩ or higher) to confirm that there is a short to +B in the one bus line only.

      HINT:
      1. Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.
      2. Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.

  1. When there is no short to +B in any of the bus lines that connect to the ECUs and sensors:

    1. With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.



B
Go to step 6
A


4.CHECK CAN NO. 1 JUNCTION CONNECTOR


    C240089E10
  1. Disconnect the CAN main bus line connector (I93) from the CAN No. 1 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 1 Junction Connector)
    *b
    to CAN No. 2 Junction Connector

NOTICE:
  1. Before disconnecting the connector, make a note of where it is connected.
  2. Reconnect the connector to its original position.



    C292403E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I39-14 (CANL) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    Text in Illustration 
    *1
    DLC3



NG
REPLACE CAN NO. 1 JUNCTION CONNECTOR
OK


5.CHECK CAN NO. 2 JUNCTION CONNECTOR (CAN NO. 1 J/C - CAN NO. 2 J/C)
  1. Reconnect the CAN main bus line connector (I93) to the CAN No. 1 junction connector.



    C250962E02
  1. Disconnect the CAN main bus line connector (I101) from the CAN No. 2 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 2 Junction Connector)
    *b
    to CAN No. 1 Junction Connector

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C292403E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I39-14 (CANL) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN BUS MAIN LINE (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 2 JUNCTION CONNECTOR)
OK

REPLACE CAN NO. 2 JUNCTION CONNECTOR 

6.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
  1. Reconnect the connector of the bus line that is shorted to +B to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or higher when it was disconnected).

  1. Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU or sensor to which the bus line shorted to +B is connected (Click here).



    C292403E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I39-14 (CANL) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    Text in Illustration 
    *1
    DLC3

    HINT:
    If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR 

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR)
  1. Disconnect the cable from the negative (-) battery terminal.



  1. Disconnect the I198 CAN No. 1 junction connector.


    C287238E05


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to CAN No. 1 Junction Connector)
    *b
    to AFS ECU*1
    (for V Bus)
    *c
    to Combination Meter Assembly
    (for V Bus)
    *d
    to Main Body ECU (Multiplex Network Body ECU)
    (for V Bus)
    *e
    to DLC3
    (for V Bus)
    *f
    to Steering Sensor
    (for V Bus)
    *g
    to Airbag Sensor Assembly
    (for V Bus)
    *h
    to Power Steering ECU with Motor Assembly
    (for V Bus)
    *i
    to Inner Rear View Mirror Assembly*2
    (for V Bus)
    *j
    to Telematics Transceiver*3
    (for V Bus)
    *k
    to CAN No. 2 Junction Connector
    (for V Bus)
    -
    -
    *1: w/ AFS
    *2: w/ Automatic High Beam System
    *3: w/ Telematics Transceiver

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Connected to
    I198-1 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    AFS ECU*1
    I198-11 (CANL) - I39-16 (BAT)
    I198-2 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Combination meter assembly
    I198-12 (CANL) - I39-16 (BAT)
    I198-3 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Main body ECU (Multiplex network body ECU)
    I198-13 (CANL) - I39-16 (BAT)
    I198-4 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    DLC3
    I198-14 (CANL) - I39-16 (BAT)
    I198-5 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Steering sensor
    I198-15 (CANL) - I39-16 (BAT)
    I198-6 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Airbag sensor assembly
    I198-16 (CANL) - I39-16 (BAT)
    I198-7 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Power steering ECU with motor assembly
    I198-17 (CANL) - I39-16 (BAT)
    I198-8 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Inner rear view mirror assembly*2
    I198-18 (CANL) - I39-16 (BAT)
    I198-9 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    Telematics transceiver*3
    I198-19 (CANL) - I39-16 (BAT)
    I198-10 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    CAN No. 2 junction connector
    I198-20 (CANL) - I39-16 (BAT)

    *1: w/ AFS
    *2: w/ Automatic High Beam System
    *3: w/ Telematics Transceiver

    Result:

    Result
    Proceed to
    OK
    A
    NG (CAN No. 2 junction connector main lines)
    B
    NG (DLC3 branch line)
    C
    NG (ECU or sensor bus line)
    D



B
Go to step 8

C
REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

D
Go to step 10
A

REPLACE CAN NO. 1 JUNCTION CONNECTOR 

8.CHECK CAN NO. 2 JUNCTION CONNECTOR (CAN NO. 1 J/C - CAN NO. 2 J/C)
  1. Reconnect the I198 CAN No. 1 junction connector.



    C250962E02
  1. Disconnect the CAN main bus line connector (I101) from the CAN No. 2 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 2 Junction Connector)
    *b
    to CAN No. 1 Junction Connector

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C292403E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I39-14 (CANL) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN BUS MAIN LINE (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 2 JUNCTION CONNECTOR)
OK


9.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 2 JUNCTION CONNECTOR)
  1. Reconnect the CAN main bus line connector (I101) to the CAN No. 2 junction connector.



    C292403E02
  1. Disconnect the connectors (I102, I104, I105, I106, I107, I111 and I188) from the CAN No. 2 junction connector one at a time.

    HINT:
    Disconnect the ECU and sensor connectors other than the CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.

    Text in Illustration 
    *1
    DLC3



  1. Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.


    C311106E02


    Text in Illustration 
    *a
    Component without harness connected
    (CAN No. 2 Junction Connector)
    -
    -

    Wiring Color 
    CAN No. 2 Junction Connector Side
    Code
    Color (CANH Side)
    Color (CANL Side)
    CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector)
    I101
    B
    W
    Air conditioning amplifier assembly
    I102
    V
    W
    ECM
    I104
    P
    W
    Smart key ECU assembly (Certification ECU)*1
    I106
    L
    W
    Clearance warning ECU assembly*2
    I111
    BE
    W
    1. Navigation receiver assembly*3
    2. Radio and display receiver assembly*4
    I107
    R
    W
    Network Gateway ECU*5
    I188
    G
    W
    Brake actuator assembly
    I105
    Y
    W
    *1: w/ Smart Entry and Start System
    *2: w/ Toyota Parking Assist-sensor System
    *3: for Navigation Receiver Type
    *4: for Radio and Display Type
    *5: w/ Network Gateway ECU

    NOTICE:
    Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to +B in 2 or more CAN bus lines.


    Result:

    Symptom
    Proceed to
    The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector. (There is a short to +B in the CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.)
    A
    The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector. (There is a short to +B in one of the areas that relate to one or more of the disconnected bus lines.)
    B

  1. When there is a short to +B in one or more of the bus lines that connect to an ECU or sensor:

    1. Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to +B). Check that the resistance shown on the tester is normal (6 kΩ or higher) to confirm that there is a short to +B in the one bus line only.

      HINT:
      1. Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.
      2. Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.

  1. When there is no short to +B in any of the bus lines that connect to the ECUs and sensors:

    1. With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.



B
Go to step 10
A

REPLACE CAN NO. 2 JUNCTION CONNECTOR 

10.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
  1. Reconnect the connector of the bus line that is shorted to +B to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or higher when it was disconnected).

  1. Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU or sensor to which the bus line shorted to +B is connected (Click here).



    C292403E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I39-14 (CANL) - I39-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    Text in Illustration 
    *1
    DLC3

    HINT:
    If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR