CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to GND (LHD Models) |
| Symptom | Trouble Area |
| No resistance exists between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of DLC3. |
|



| 1.CHECK VEHICLE TYPE |
Check vehicle type.
| Result | Proceed to |
| except TMMR Made | A |
| for TMMR Made | B |
|
| ||||
| A | |
| 2.CHECK FOR SHORT TO GND IN CAN BUS LINE (DLC3 BRANCH LINE) |
Disconnect the cable from the negative (-) battery terminal.
![]() |
Disconnect the DLC3 branch line connector (I96) from the CAN No. 1 junction connector.
| *a | Rear view of wire harness connector (to CAN No. 1 Junction Connector) |
| *b | to DLC3 |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| *1 | DLC3 |
|
| ||||
| OK | |
| 3.CHECK FOR SHORT TO GND IN CAN BUS LINE |
Reconnect the DLC3 branch line connector (I96) to the CAN No. 1 junction connector.
![]() |
Disconnect the connectors (I94, I95, I97, I100, I102, I103, I104, I105, I106, I107, I111, I112 and I188) from the CAN No. 1 junction connector and CAN No. 2 junction connector one at a time.
| *1 | DLC3 |
Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 4 (CG), and between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.

| *A | w/ Toyota Parking Assist-sensor System | *B | w/ Smart Entry and Start System |
| *C | for Navigation Receiver Type | *D | for Radio and Display Type |
| *E | w/ Network Gateway ECU | *F | w/ AFS |
| *1 | Clearance Warning ECU Assembly | *2 | Air Conditioning Amplifier Assembly |
| *3 | ECM | *4 | Brake Actuator Assembly |
| *5 | Smart Key ECU Assembly (Certification ECU) | *6 | Navigation Receiver Assembly |
| *7 | Radio and Display Receiver Assembly | *8 | Network Gateway ECU |
| *9 | Combination Meter Assembly | *10 | Power Steering ECU with Motor Assembly |
| *11 | DLC3 | *12 | Airbag Sensor Assembly |
| *13 | Steering Sensor | *14 | Main Body ECU (Multiplex Network Body ECU) |
| *15 | AFS ECU | *16 | CAN No. 1 Junction Connector |
| *17 | CAN No. 2 Junction Connector | - | - |

| *a | Component without harness connected (CAN No. 1 Junction Connector) | - | - |
| CAN No. 1 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
| AFS ECU* | I112 | BE | W |
| Main body ECU (Multiplex network body ECU) | I95 | P | W |
| Steering sensor | I97 | V | W |
| Airbag sensor assembly | I103 | Y | W |
| DLC3 | I96 | L | W |
| Power steering ECU with motor assembly | I100 | G | W |
| Combination meter assembly | I94 | R | W |
| CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) | I93 | B | W |

| *a | Component without harness connected (CAN No. 2 Junction Connector) | - | - |
| CAN No. 2 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
| CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) | I101 | B | W |
| Air conditioning amplifier assembly | I102 | V | W |
| ECM | I104 | P | W |
| Smart key ECU assembly (Certification ECU)*1 | I106 | L | W |
| Clearance warning ECU assembly*2 | I111 | BE | W |
| Network Gateway ECU*3 | I188 | G | W |
| I107 | R | W |
| Brake actuator assembly | I105 | Y | W |
| Symptom | Proceed to |
| The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector. (There is a short to GND in the CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.) | A |
| The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) becomes normal (200 Ω or higher) when a connector is disconnected from the CAN junction connector. (There is a short to GND in one of the areas that relate to the disconnected bus lines.) | B |
When there is a short to GND in one or more of the bus lines that connect to an ECU or sensor:
Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to GND). Check that the resistance shown on the tester is normal (200 Ω or higher) to confirm that there is a short to GND in the one branch line only.
When there is no short to GND in any of the bus lines that connect to the ECUs and sensors:
With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.
|
| ||||
| A | |
| 4.CHECK CAN NO. 1 JUNCTION CONNECTOR |
![]() |
Disconnect the CAN main bus line connector (I93) from the CAN No. 1 junction connector.
| *a | Rear view of wire harness connector (to CAN No. 1 Junction Connector) |
| *b | to CAN No. 2 Junction Connector |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| *1 | DLC3 |
|
| ||||
| OK | |
| 5.CHECK CAN NO. 2 JUNCTION CONNECTOR (CAN NO. 1 J/C - CAN NO. 2 J/C) |
Reconnect the CAN main bus line connector (I93) to the CAN No. 1 junction connector.
![]() |
Disconnect the CAN main bus line connector (I101) from the CAN No. 2 junction connector.
| *a | Rear view of wire harness connector (to CAN No. 2 Junction Connector) |
| *b | to CAN No. 1 Junction Connector |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||
| 6.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR) |
Reconnect the connector of the bus line that is shorted to GND to the CAN junction connector (the connector that caused the bus line resistance to change to 200 Ω or higher when it was disconnected).
Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU or sensor to which the bus line shorted to GND is connected (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||
| 7.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR) |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the I198 CAN No. 1 junction connector.

| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector (to CAN No. 1 Junction Connector) | *b | to AFS ECU*1 (for V Bus) |
| *c | to Combination Meter Assembly (for V Bus) | *d | to Main Body ECU (Multiplex Network Body ECU) (for V Bus) |
| *e | to DLC3 (for V Bus) | *f | to Steering Sensor (for V Bus) |
| *g | to Airbag Sensor Assembly (for V Bus) | *h | to Power Steering ECU with Motor Assembly (for V Bus) |
| *i | to Inner Rear View Mirror Assembly*2 (for V Bus) | *j | to Telematics Transceiver*3 (for V Bus) |
| *k | to CAN No. 2 Junction Connector (for V Bus) | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| I198-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | AFS ECU*1 |
| I198-11 (CANL) - I39-4 (CG) | |||
| I198-2 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Combination meter assembly |
| I198-12 (CANL) - I39-4 (CG) | |||
| I198-3 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Main body ECU (Multiplex network body ECU) |
| I198-13 (CANL) - I39-4 (CG) | |||
| I198-4 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | DLC3 |
| I198-14 (CANL) - I39-4 (CG) | |||
| I198-5 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Steering sensor |
| I198-15 (CANL) - I39-4 (CG) | |||
| I198-6 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Airbag sensor assembly |
| I198-16 (CANL) - I39-4 (CG) | |||
| I198-7 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Power steering ECU with motor assembly |
| I198-17 (CANL) - I39-4 (CG) | |||
| I198-8 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Inner rear view mirror assembly*2 |
| I198-18 (CANL) - I39-4 (CG) | |||
| I198-9 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Telematics transceiver*3 |
| I198-19 (CANL) - I39-4 (CG) | |||
| I198-10 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | CAN No. 2 junction connector |
| I198-20 (CANL) - I39-4 (CG) |
| Result | Proceed to |
| OK | A |
| NG (CAN No. 2 junction connector main lines) | B |
| NG (DLC3 branch line) | C |
| NG (ECU or sensor bus line) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 8.CHECK CAN NO. 2 JUNCTION CONNECTOR (CAN NO. 1 J/C - CAN NO. 2 J/C) |
Reconnect the I198 CAN No. 1 junction connector.
![]() |
Disconnect the CAN main bus line connector (I101) from the CAN No. 2 junction connector.
| *a | Rear view of wire harness connector (to CAN No. 2 Junction Connector) |
| *b | to CAN No. 1 Junction Connector |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| *1 | DLC3 |
|
| ||||
| OK | |
| 9.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 2 JUNCTION CONNECTOR) |
Reconnect the CAN main bus line connector (I101) to CAN No. 2 junction connector.
![]() |
Disconnect the connectors (I102, I104, I105, I106, I107, I111 and I188) from the CAN No. 2 junction connector one at a time.
| *1 | DLC3 |
Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 4 (CG), and between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.

| *a | Component without harness connected (CAN No. 2 Junction Connector) | - | - |
| CAN No. 2 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
| CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) | I101 | B | W |
| Air conditioning amplifier assembly | I102 | V | W |
| ECM | I104 | P | W |
| Smart key ECU assembly (Certification ECU)*1 | I106 | L | W |
| Clearance warning ECU assembly*2 | I111 | BE | W |
| I107 | R | W |
| Network Gateway ECU*5 | I188 | G | W |
| Brake actuator assembly | I105 | Y | W |
| Symptom | Proceed to |
| The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector. (There is a short to GND in the CAN main bus lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.) | A |
| The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) becomes normal (200 Ω or higher) when a connector is disconnected from the CAN junction connector. (There is a short to GND in one of the areas that relate to the disconnected bus lines.) | B |
When there is a short to GND in one or more of the bus lines that connect to an ECU or sensor:
Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to GND). Check that the resistance shown on the tester is normal (200 Ω or higher) to confirm that there is a short to GND in the one branch line only.
When there is no short to GND in any of the bus lines that connect to the ECUs and sensors:
With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the CAN No. 1 junction connector and CAN No. 2 junction connector.
|
| ||||
| A | ||
| ||
| 10.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR) |
Reconnect the connector of the bus line that is shorted to GND to the CAN junction connector (the connector that caused the bus line resistance to change to 200 Ω or higher when it was disconnected).
Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU or sensor to which the bus line shorted to GND is connected (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||