AUTOMATIC TRANSAXLE SYSTEM > Transmission Control Switch Circuit |

| 1.READ VALUE USING INTELLIGENT TESTER (SPORT SHIFT SWITCH STATUS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
In accordance with the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Sports Shift Up SW | Sport shift up switch status/ ON or OFF |
| - |
| Sports Shift Down SW | Sport shift down switch status/ ON or OFF |
| - |
| Result | Proceed to |
| Data display is not within Normal Condition range | A |
| Data display is within Normal Condition range | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH) |
![]() |
Disconnect the transmission control switch connector from lower shift lever assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Condition | Condition | Specified Condition |
| l44-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| *a | Front view of wire harness connector (to Transmission Control Switch) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| l44-2 (E) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Transmission Control Switch) |
|
| ||||
| OK | |
| 4.INSPECT LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH) |
![]() ![]() |
Measure the resistance between each terminal of the transmission control switch when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
| l44-4 (IG) - l44-5 (S) | Shift lever in S, "+" or "-" | Below 1 Ω |
| Shift lever not in S, "+" or "-" | 10 kΩ or higher | |
| l44-3 (SFTU) - l44-2 (E) | Shift lever held in "+" (Up-shift) | Below 1 Ω |
| Shift lever not held in "+" | 10 kΩ or higher | |
| l44-1 (SFTD) - l44-2 (E) | Shift lever held in "-" (Down-shift) | Below 1 Ω |
| Shift lever not held in "-" | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| l44-4 (IG) - l44-5 (S) | Shift lever in S, "+" or "-" | Below 1 Ω |
| Shift lever not in S, "+" or "-" | 10 kΩ or higher | |
| l44-1 (SFTU) - l44-2 (E) | Shift lever held in "+" (Up-shift) | Below 1 Ω |
| Shift lever not held in "+" | 10 kΩ or higher | |
| l44-3 (SFTD) - l44-2 (E) | Shift lever held in "-" (Down-shift) | Below 1 Ω |
| Shift lever not held in "-" | 10 kΩ or higher |
| *a | Component without harness connected (Transmission Control Switch for LHD) |
| *b | Component without harness connected (Transmission Control Switch for RHD) |
| Result | Proceed to |
| OK | A |
| NG (for TMC, TMMR Made) | B |
| NG (for TMMK Made) | C |
|
| ||||
|
| ||||
| A | |
| 5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM) |
Connect the transmission control switch connector.
![]() |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A25-27 (S) - Body ground |
| 11 to 14 V |
| A25-27 (S) - Body ground |
| Below 1 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A25-42 (SFTU) - Body ground | Shift lever held in "+" (Up-shift) | Below 1 Ω |
| Shift lever not held in "+" | 10 kΩ or higher | |
| A25-43 (SFTD) - Body ground | Shift lever held in "-" (Down-shift) | Below 1 Ω |
| Shift lever not held in "-" | 10 kΩ or higher |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||