Home › Drivetrain · U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > Transmission Control Switch Circuit

for Preparation Click here


DESCRIPTION

When the shift lever is in S and it is moved toward "-" or "+", it is possible to select different shift ranges (1st through 6th ranges).
Moving the shift lever toward "+" increases the shift range by one, and moving the shift lever toward "-" decreases the shift range by one.

WIRING DIAGRAM


C298736E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING INTELLIGENT TESTER (SPORT SHIFT SWITCH STATUS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. In accordance with the display on the intelligent tester, read the Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Sports Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Continuously shift to "+" (up-shift)
    2. OFF: Release "+" (up-shift)
    -
    Sports Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Continuously shift to "-" (down-shift)
    2. OFF: Release "-" (down-shift)
    -

Result:
Result
Proceed to
Data display is not within Normal Condition range
A
Data display is within Normal Condition range
B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)


    C245154E01
  1. Disconnect the transmission control switch connector from lower shift lever assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Condition
    Condition
    Specified Condition
    l44-4 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transmission Control Switch)



NG
CHECK POWER SOURCE CIRCUIT
OK


3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)


    C245154E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    l44-2 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transmission Control Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH)


    C239095E01
    C239095E10
  1. Measure the resistance between each terminal of the transmission control switch when the shift lever is moved to each position.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    l44-4 (IG) - l44-5 (S)
    Shift lever in S, "+" or "-"
    Below 1 Ω
    Shift lever not in S, "+" or "-"
    10 kΩ or higher
    l44-3 (SFTU) - l44-2 (E)
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    Shift lever not held in "+"
    10 kΩ or higher
    l44-1 (SFTD) - l44-2 (E)
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    Shift lever not held in "-"
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    l44-4 (IG) - l44-5 (S)
    Shift lever in S, "+" or "-"
    Below 1 Ω
    Shift lever not in S, "+" or "-"
    10 kΩ or higher
    l44-1 (SFTU) - l44-2 (E)
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    Shift lever not held in "+"
    10 kΩ or higher
    l44-3 (SFTD) - l44-2 (E)
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    Shift lever not held in "-"
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Control Switch for LHD)
    *b
    Component without harness connected
    (Transmission Control Switch for RHD)

Result:
Result
Proceed to
OK
A
NG (for TMC, TMMR Made)
B
NG (for TMMK Made)
C



B
REPLACE LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH) (Click here)

C
REPLACE LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH) (Click here)
A


5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
  1. Connect the transmission control switch connector.



    C233487E04
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A25-27 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever in S, "+" or "-"
    11 to 14 V
    A25-27 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever not in S, "+" or "-"
    Below 1 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A25-42 (SFTU) - Body ground
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    Shift lever not held in "+"
    10 kΩ or higher
    A25-43 (SFTD) - Body ground
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    Shift lever not held in "-"
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)