Home › Engine / Hybrid System · 2AR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P2014    Intake Manifold Runner Position Sensor / Switch Circuit (Bank 1)

DTC    P2016    Intake Manifold Runner Position Sensor / Switch Circuit Low (Bank 1)

DTC    P2017    Intake Manifold Runner Position Sensor / Switch Circuit High (Bank 1)

for Preparation Click here


DESCRIPTION

The Tumble Control Valve (TCV) position sensor is a non-contact type sensor.
The position sensor measures the opening angle of the tumble control valve. The sensor is reliable and accurate, as it is electrically controlled by Hall-effect elements.

A257646E02


DTC No.
DTC Detection Connection
Trouble Area
P2014
The tumble control valve position sensor output voltage flutters up and down beyond the normal operating range (less than 0.2 V, or higher than 4.8 V) for more than 0.5 seconds (open or short) (1 trip detection logic).
  1. Open or short in tumble control valve position sensor circuit
  2. Intake air control valve actuator (for tumble control valve)
  3. ECM
P2016
The tumble control valve position sensor output voltage is less than 0.2 V for more than 0.5 seconds (short) (1 trip detection logic).
  1. Open or short in tumble control valve position sensor circuit
  2. Intake air control valve actuator (for tumble control valve)
  3. ECM
P2017
The tumble control valve position sensor output voltage is higher than 4.8 V for more than 0.5 seconds (open) (1 trip detection logic).
  1. Open or short in tumble control valve position sensor circuit
  2. Intake air control valve actuator (for tumble control valve)
  3. ECM

HINT:
When DTC P2014, P2016 or P2017 is output, use the intelligent tester to confirm the IAC Sensor Voltage (tumble control valve position sensor output voltage). Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / IAC Sensor Voltage.


IAC Sensor Voltage
Malfunction
0.2 V or less
  1. IAC1 circuit shorted
  2. VCIA circuit open
4.8 V or higher
  1. VCIA and IAC1 circuits shorted
  2. IAC1 circuit open
  3. EIA1 circuit open

MONITOR DESCRIPTION

The ECM IAC1 terminal voltage increases in correlation with the opening angle of the tumble control valve. When the tumble control valve is fully closed, approximately 0.94 V is applied to the IAC1 terminal. When the tumble control valve is fully open, approximately 3.4 V is applied to the IAC1 terminal.
When the output voltage of the IAC1 terminal deviates from the standard range, the ECM determines that a malfunction has occurred in the position sensor and stores a DTC.

MONITOR STRATEGY


Required Sensors/Components
Intake air control valve actuator (for tumble control valve)
Frequency of Operation
Continuous

COMPONENT OPERATING RANGE


Tumble control valve position sensor voltage
0.2 to 4.8 V

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on.
  6. Wait 0.5 seconds or more.
  7. Enter the following menus: Powertrain / Engine and ECT / DTC.
  8. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P2014, P2016 or P2017.
  11. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM

Refer to DTC P2004 .

INSPECTION PROCEDURE

HINT:
  1. If DTCs relating to different systems which share terminal EIA1 as their ground are stored simultaneously, there may be an open circuit between terminal EIA1 and ground.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE IAC DUTY RATIO)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the IAC Duty Ratio / All Data / IAC Sensor Voltage.

  1. Check the value of IAC Sensor Voltage while changing Control the IAC Duty Ratio from -100 to 100% (or from 100 to -100%) using the tester.

    OK:
    The value of IAC Sensor Voltage remains between 0.2 and 4.8 V while Control the IAC Duty Ratio is changed from -100 to 100% (or from 100 to -100%).

    HINT: 
    Control the IAC Duty Ratio
    Operation
    IAC Sensor Voltage
    (Normal)
    Suspected Trouble Area
    1. IAC1 circuit shorted
    2. VCIA circuit open
    1. VCIA and IAC1 circuits shorted
    2. IAC1 circuit open
    3. EIA1 circuit open
    Sensor malfunction
    -100%
    0.2 to 1.4 V
    Remains below 0.2 V
    Remains higher than 4.8 V
    Other than the voltage in the 2 columns on the left
    100%
    3.2 to 4.8 V
    Remains below 0.2 V
    Remains higher than 4.8 V



NG
Go to step 3
OK


2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2014, P2016 AND/OR P2017)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P2014, P2016 and/or P2017 is output
    A
    DTC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE ECM (Click here)  

3.CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ACTUATOR - ECM)
  1. Disconnect the ECM connector.

  1. Disconnect the intake air control valve actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Y4-3 (VDD) - E26-130 (VCIA)
    Always
    Below 1 Ω
    Y4-1 (OUT) - E26-131 (IAC1)
    Always
    Below 1 Ω
    Y4-2 (GND) - E26-129 (EIA1)
    Always
    Below 1 Ω
    Y4-3 (VDD) or E26-130 (VCIA) - Body ground
    Always
    10 kΩ or higher
    Y4-1 (OUT) or E26-131 (IAC1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INTAKE AIR CONTROL VALVE ACTUATOR)
A211274E05
  1. Disconnect the intake air control valve actuator connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Y4-3 (VDD) - Body ground
    Ignition switch ON
    4.5 to 5.0 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Intake Air Control Valve Actuator)



NG
REPLACE ECM (Click here)
OK


5.REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)
  1. Replace the intake air control valve actuator (for tumble control valve) (Click here).


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2014, P2016 AND/OR P2017)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P2014, P2016 and/or P2017 is output
    A
    DTC is not output
    B



B
END
A

REPLACE ECM (Click here)