Home › Vehicle Interior › INTERIOR PANELS / TRIM › REAR SUNSHADE SYSTEM

REAR SUNSHADE SYSTEM > Rear Sunshade does not Operate with Rear Sunshade Switch

for Preparation Click here


DESCRIPTION

When the rear sunshade switch is pushed, an operation signal is sent to the rear sunshade relay (rear window shade assembly).

WIRING DIAGRAM


B281867E06


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK REAR SUNSHADE OPERATION
  1. Check rear sunshade operation.

Result:
Result
Proceed to
The rear sunshade does not operate with rear sunshade switch assembly operation.
A
The rear sunshade does not operate with cooler control switch assembly (rear sunshade switch) operation.
B
The rear sunshade does not operate with rear sunshade switch assembly and cooler control switch assembly (rear sunshade switch) operation.
C



B
Go to step 4

C
Go to step 6
A


2.INSPECT REAR SUNSHADE SWITCH ASSEMBLY


    E124884E03
  1. Remove the rear sunshade switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (ECU) - 3 (E2)
    Rear sunshade switch pushed
    Below 1 Ω
    6 (ECU) - 3 (E2)
    Rear sunshade switch not pushed
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Sunshade Switch Assembly)



NG
REPLACE REAR SUNSHADE SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY) - REAR SUNSHADE SWITCH ASSEMBLY - BODY GROUND)
  1. Disconnect the N19 rear sunshade relay (rear window shade assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N19-5 (SW) - I50-6 (ECU)
    Always
    Below 1 Ω
    N19-5 (SW) - Body ground
    Always
    10 kΩ or higher
    I50-3 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY) (Click here)  

4.INSPECT COOLER CONTROL SWITCH ASSEMBLY (REAR SUNSHADE SWITCH)


    E228036E02
  1. Remove the cooler control switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    12 (ECU) - 16 (GND)
    Rear sunshade switch pushed
    Below 1 Ω
    12 (ECU) - 16 (GND)
    Rear sunshade switch not pushed
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Cooler Control Switch Assembly)



NG
REPLACE COOLER CONTROL SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY) - COOLER CONTROL SWITCH ASSEMBLY - BODY GROUND)
  1. Disconnect the N19 rear sunshade relay (rear window shade assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N19-4 (RSW) - X1-12 (ECU)
    Always
    Below 1 Ω
    N19-4 (RSW) - Body ground
    Always
    10 kΩ or higher
    X1-16 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY) (Click here)  

6.CHECK HARNESS AND CONNECTOR (REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY) - BATTERY AND BODY GROUND)
  1. Disconnect the N19 rear sunshade relay (rear window shade assembly) connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    N19-8 (B) - Body ground
    Always
    11 to 14 V
    N19-7 (IG) - Body ground
    Engine switch off
    Below 1 V
    N19-7 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N19-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY) (Click here)