Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR (for TMMK Made)

FRONT DOOR (for TMMK Made) > ADJUSTMENT

for Preparation Click here


B280381E03
Text in Illustration 
*a
Centering Bolt
*b
Standard Bolt

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.
  3. Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.
  4. Specified torque for standard bolts is shown in the standard bolt chart (Click here).



1. INSPECT FRONT DOOR


  1. Check that the clearance measurements of areas a through p are within each standard range.


    B380700E01


    Standard Clearance 
    Area
    Measurement
    Area
    Measurement
    a
    3.35 to 6.35 mm (0.132 to 0.250 in.)
    b
    8.8 to 11.8 mm (0.346 to 0.465 in.)
    c
    3.35 to 6.35 mm (0.132 to 0.250 in.)
    d
    1.7 to 4.7 mm (0.0669 to 0.185 in.)
    e
    3.35 to 6.35 mm (0.132 to 0.250 in.)
    f
    1.0 to 4.0 mm (0.0394 to 0.157 in.)
    g
    2.3 to 6.3 mm (0.0906 to 0.248 in.)
    h
    2.96 to 4.64 mm (0.117 to 0.183 in.)
    i
    -0.84 to 0.84 mm (-0.0331 to 0.0331 in.)
    j
    2.96 to 4.64 mm (0.117 to 0.183 in.)
    k
    -0.84 to 0.84 mm (-0.0331 to 0.0331 in.)
    l
    3.05 to 7.25 mm (0.120 to 0.285 in.)
    m
    3.0 to 5.4 mm (0.118 to 0.213 in.)
    n
    -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)
    o
    3.0 to 5.4 mm (0.118 to 0.213 in.)
    p
    -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)



2. REMOVE FRONT WHEEL


3. REMOVE FRONT WHEEL OPENING EXTENSION PAD

HINT:
Use the same procedure for the RH side and LH side .



4. REMOVE FRONT FENDER LINER

HINT:
Use the same procedure for the RH side and LH side .



5. REMOVE FRONT FENDER SEAL


    B380701
  1. Disengage the 3 clips and remove the front fender seal.



6. ADJUST FRONT DOOR

NOTICE:
Make sure that the turn the engine switch off when adjusting door lock strikers.



    B280380
  1. Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

    SST
    09812-00010  

  1. Tighten the hinge bolts on the vehicle body after adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. Loosen the hinge bolts on the door and adjust the door position.

  1. Tighten the hinge bolts on the door after adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



    B280382
  1. Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.

  1. Using a brass bar and a hammer, hit the striker to adjust its position.

  1. Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



7. INSTALL FRONT FENDER SEAL
  1. Install the front fender seal with 3 new clips.



8. INSTALL FRONT FENDER LINER

HINT:
Use the same procedure for the RH side and LH side .



9. INSTALL FRONT WHEEL OPENING EXTENSION PAD

HINT:
Use the same procedure for the RH side and LH side .



10. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }