DTC P0504 Brake Switch "A" / "B" Correlation |
| Signal (ECM Terminal) | Brake Pedal Released | In Transition | Brake Pedal Depressed |
| STP | OFF | ON | ON |
| ST1- | ON | ON | OFF |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0504 | Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON. (b) STP signal off when ST1- signal off. |
|



| Brake Pedal Operation | Stop Light Switch | ST1 |
| Depressed | ON | ON |
| Released | OFF | OFF |
| 1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY) |
Disconnect the stop light switch assembly connector.

Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A33-2 - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| A77-1 (B) - Body ground | Always | 11 to 14 V |
| *A | for LED Type | *B | for Bulb Type |
| *a | Front view of wire harness connector (to Stop Light Switch Assembly) | - | - |
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY) |
Disconnect the stop light switch assembly connector.

Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A33-4 - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| A77-5 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | for LED Type | *B | for Bulb Type |
| *a | Front view of wire harness connector (to Stop Light Switch Assembly) | - | - |
| Result | Proceed to |
| OK (for LED Type) | A |
| OK (for Bulb Type) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND) |
Disconnect the stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A77-3 (GND) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE) |
Disconnect the ECM connector.

Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A25-24 (ST1-) - Body ground | Brake pedal released | 7.5 to 14 V |
| Brake pedal depressed | Below 1.5 V | |
| A25-11 (STP) - Body ground | Brake pedal released | Below 1.5 V |
| Brake pedal depressed | 7.5 to 14 V |
| *a | Brake Pedal Depressed | *b | Brake Pedal Released |
| *c | Front view of wire harness connector (to ECM) | - | - |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM) |
Disconnect the stop light switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A33-1 - A25-11 (STP) | Always | Below 1 Ω |
| A33-3 - A25-24 (ST1-) | Always | Below 1 Ω |
| A33-1 or A25-11 (STP) - Body ground | Always | 10 kΩ or higher |
| A33-3 or A25-24 (ST1-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A77-2 (OUT) - A25-11 (STP) | Always | Below 1 Ω |
| A77-4 (L) - A25-24 (ST1-) | Always | Below 1 Ω |
| A77-2 (OUT) or A25-11 (STP) - Body ground | Always | 10 kΩ or higher |
| A77-4 (L) or A25-24 (ST1-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - STOP LIGHT SWITCH ASSEMBLY) |
Remove the No. 1 integration relay from the engine room relay block and junction block assembly.
Disconnect the stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1C-2 - A33-4 | Always | Below 1 Ω |
| 1C-2 or A33-4 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 1C-2 - A77-5 (B) | Always | Below 1 Ω |
| 1C-2 or A77-5 (B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||