Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)

DTC    B2274    ACC Monitor Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit that goes from the ACC output terminal of the certification ECU (smart key ECU assembly) to the ACC relay.

HINT:
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2274
Malfunction in the ACC relay circuit in the certification ECU (smart key ECU assembly) or in the external circuit (1-trip detection logic*).

HINT:
When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.

  1. AM2 fuse
  2. ACC relay (Instrument panel junction block assembly)
  3. Certification ECU (smart key ECU assembly)
  4. Wire harness or connector
Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off.
  1. *: Only detected while a malfunction is present.

Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
  1. If there is a malfunction due to the relay being stuck on, the ACC relay does not turn off even though the engine switch is off.
  2. If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the engine switch is on (ACC).

HINT:
The engine switch can be turned on (IG) and the engine can be started.

-

WIRING DIAGRAM


B285916E01


INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body / Entry & Start / DTC.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) precaution (Click here).
  4. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  5. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


HINT:

Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
B2274
Power Source Control
  1. ACC Relay Monitor
Starting Control
  1. Ignition
-

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B268625E07
  1. Disconnect the A43 connector from the certification ECU (smart key ECU assembly).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A43-2 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU (smart key ECU assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


2.CHECK HARNESS AND CONNECTOR (GROUND)
B268625E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A43-11 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU (smart key ECU assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the I78 connector from the certification ECU (smart key ECU assembly).

  1. Disconnect the 3B connector from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I78-4 (ACCD) - 3B-23
    Always
    Below 1 Ω
    3B-7 - Body ground
    Always
    Below 1 Ω
    I78-4 (ACCD) or 3B-23 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)


  1. Remove the instrument panel junction block assembly (Click here).


    B288688E09


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    1. 3E-1 - 3B-37
    2. 3E-1 - 3A-32
    Battery voltage not applied to terminals 3B-23 and 3B-7
    10 kΩ or higher
    Battery voltage applied to terminals 3B-23 and 3B-7
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    1. 3F-1 - 3B-37
    2. 3F-1 - 3A-32
    Battery voltage not applied to terminals 3B-23 and 3B-7
    10 kΩ or higher
    Battery voltage applied to terminals 3B-23 and 3B-7
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK


5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B268626E04
  1. Reconnect the I78 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I78-4 (ACCD) - Body ground
    Engine switch off → Engine switch on (ACC)
    1 V or less → 8.5 V or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

USE SIMULATION METHOD TO CHECK (Click here)