Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > DTC CHECK / CLEAR

for Preparation Click here



DTC CHECK/CLEAR (When Using the Intelligent Tester)
  1. Check for DTCs.

    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the intelligent tester on.

    5. Read the DTCs following the prompts on the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.

    6. Check the details of the DTCs (Click here).

  2. Clear the DTCs.

    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the intelligent tester on.

    5. Operate the intelligent tester to clear the codes. Enter the following menus: Chassis / ABS/VSC/TRC / DTC / Clear.


DTC CHECK/CLEAR (When not Using the Intelligent Tester)


  1. Check for DTCs.

    1. Turn the ignition switch off.



    2. C166029E42
    3. Using SST, connect terminals TC and CG of the DLC3.

      SST
      09843-18040  
      Text in Illustration 
      *a
      Front view of DLC3

    4. Turn the ignition switch to ON.

    5. Observe the blinking pattern of the ABS warning and slip indicator lights in order to identify the DTC.

      HINT:
      If no code appears, inspect the TC and CG terminal circuit, and ABS warning and slip indicator light circuits.

      Trouble Area
      See Procedure
      TC and CG terminal circuit
      Click here
      ABS warning light circuit (Remains on)
      Click here
      ABS warning light circuit (Does not come on)
      Click here
      Slip indicator light circuit (Remains on)
      Click here
      Slip indicator light circuit (Does not come on)
      Click here

    6. Count the number of blinks of the ABS warning and slip indicator lights.

      HINT:
      1. How to read DTCs:
        Diagnostic trouble codes are represented by the number of blinks of a warning light. For example, code 21 would be shown by 2 blinks, a pause of 1.5 seconds, and then 1 blink.
      2. If one code is detected:
        The light repeats the same code after a pause of 4 seconds.
      3. If multiple codes are detected:
        The light outputs one code after another with a 2.5-second pause between each code. When all codes have been output, there is a 4-second pause and then the light begins to output the codes again.

    7. Check the details of the DTCs.

      ABS DTC 
      ABS Warning Light Display
      Tester Display
      11
      C146E
      13
      C146C
      21
      C1468
      22
      C1469
      23
      C146A
      24
      C146B
      25
      C1225
      26
      C1226
      27
      C1227
      28
      C1228
      31
      C1464
      32
      C1465
      33
      C1466
      34
      C1467
      35
      C1330
      36
      C1331
      37
      C1237
      38
      C1332
      39
      C1333
      41
      C1241
      C1417
      46
      C1246
      49
      C1249
      C1425
      C1426
      51
      C1428
      62
      C1300
      67
      C1429
      C1430
      C1431
      94
      U0073

      VSC DTC 
      Slip Indicator Light Display
      Tester Display
      28
      C1472
      31
      C1432
      C1433
      C1434
      C1439
      C1445
      32
      C1419
      C1420
      34
      C1234
      C1435
      C1436
      43*1
      -
      44
      C1224
      51
      C1201
      62
      U0123
      63
      U0126
      65
      U0100
      6A*2
      C1381
      88
      C1288
      -
      C1441
      *1: This DTC is output when the VSC system detects a malfunction in the ABS.
      *2: The light blinks 6 times, turns off for 1.5 seconds, and then blinks 10 times.

      NOTICE:
      When the skid control ECU detects a brake booster failure, the brake warning light illuminates and the skid control ECU stores DTC C1441.

    8. After completing the check, disconnect terminals TC and CG of the DLC3 to turn off the display.
      If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.



  2. Clear the DTCs.

    1. Turn the ignition switch off.



    2. C166029E42
    3. Using SST, connect terminals TC and CG of the DLC3.

      SST
      09843-18040  
      Text in Illustration 
      *a
      Front view of DLC3

    4. Turn the ignition switch to ON.



    5. BR03890
    6. Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

    7. Check that the warning light indicates a normal system code.

    8. Remove SST from the terminals of the DLC3.

      HINT:
      The DTCs cannot be cleared by disconnecting the battery terminal or the ECU-IG1 NO. 1 fuse.


END OF DTC CHECK/CLEAR
  1. Turn the ignition switch to ON.

  2. Check that the ABS warning and slip indicator lights go off within approximately 3 seconds after turning the ignition switch to ON.