Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  7. According to the display on the tester, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ABS Warning Light
    ABS warning light / ON or OFF
    ON: Warning light on
    OFF: Warning light off
    -
    Brake Warning Light
    Brake warning light / ON or OFF
    ON: Warning light on
    OFF: Warning light off
    -
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -
    Main Idle SW
    Main idle switch / ON or OFF
    ON: Accelerator pedal released
    OFF: Accelerator pedal depressed
    -
    Brake Pedal Load Sensing SW
    Brake pedal load sensing switch / ON or OFF
    ON: Brake pedal depressed beyond a specified point
    OFF: Brake pedal not depressed beyond a specified point
    -
    Gear Position
    Gear position information / "P,N", R, 1st-8th, Fail or Not R
    Actual gear position
    -
    Shift Lever Position
    Shift lever position information / "P,N", R, D/M, 1st-6th/B or Fail
    Actual shift lever position
    -
    Shift Information
    Shift information / ON or OFF
    ON: During gear change
    -
    Inspection Mode
    Inspection mode / Other or Inspect
    Other: Normal mode
    Inspect: Inspection mode
    -
    Number of IG ON(Inspection)
    Number of times ignition switch turned to ON after entering inspection mode / Min.: 0, Max.: 255
    -
    -
    Master Cylinder Sensor
    Master cylinder pressure sensor reading / Min.: 0.00 V, Max.: 5.00 V
    Brake pedal released: 0.20 to 0.40 V
    Reading increases when brake pedal is depressed
    Deceleration Sensor
    Acceleration sensor reading / Min.: -18.525 m/s2, Max.: 18.387 m/s2
    -
    During deceleration/acceleration: Changes continuously
    Zero Point of Decele
    Memorized zero value / Min.: - 25.10 m/s2, Max.: 24.90 m/s2
    -
    -
    Deceleration Sensor2
    Acceleration sensor 2 reading / Min.: -18.525 m/s2, Max.: 18.387 m/s2
    -
    During deceleration/acceleration: Changes continuously
    Zero Point of Decele2
    Memorized zero value / Min.: - 25.10 m/s2, Max.: 24.90 m/s2
    -
    -
    Yaw Rate Sensor
    Yaw rate sensor / Min.: -128 °/s, Max.: 127 °/s
    Vehicle stopped: 0 °/s
    Turning right: -128 to 0 °/s
    Turning left: 0 to 127 °/s
    -
    Zero Point of Yaw Rate
    Memorized zero value / Min.: - 128°, Max.: 127°
    -
    After completing zero point calibration: 0°
    Steering Angle Sensor
    Steering angle sensor / Min.: -3276.8°, Max.: 3276.7°
    Turning left: Increases
    Turning right: Decreases
    -
    Zero Point of Steering Angle
    Memorized zero value / Min.: -3276.8°, Max.: 3276.7°
    -
    After steering angle sensor zero point calibration: 0°
    Lateral G
    Lateral G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
    -
    During turning: Changes in proportion with acceleration
    Forward and Rearward G
    Forward and backward G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
    -
    During acceleration/deceleration: Changes in proportion with acceleration
    Yaw Rate Value
    Yaw rate value / Min.: -128 °/s, Max.: 127 °/s
    -
    During turning: Changes in proportion with yaw
    Steering Angle Value
    Steering angle value / Min.: -3276.8°, Max.: 3276.7°
    -
    During steering operation: Changes in proportion with steering wheel rotation
    Slip Indicator Light
    Slip indicator light / ON or OFF
    ON: Indicator light on
    OFF: Indicator light off
    -
    FR Wheel Speed
    Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    FL Wheel Speed
    Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RR Wheel Speed
    Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RL Wheel Speed
    Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    Vehicle Speed
    Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    FR Wheel Acceleration
    Front wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
    -
    During deceleration/acceleration: Changes continuously
    FL Wheel Acceleration
    Front wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
    -
    During deceleration/acceleration: Changes continuously
    RR Wheel Acceleration
    Rear wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
    -
    During deceleration/acceleration: Changes continuously
    RL Wheel Acceleration
    Rear wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
    -
    During deceleration/acceleration: Changes continuously
    FR Wheel ABS Ctrl Status
    Front wheel RH ABS control status / ON or OFF
    ON: During control
    -
    FL Wheel ABS Ctrl Status
    Front wheel LH ABS control status / ON or OFF
    ON: During control
    -
    RR Wheel ABS Ctrl Status
    Rear wheel RH ABS control status / ON or OFF
    ON: During control
    -
    RL Wheel ABS Ctrl Status
    Rear wheel LH ABS control status / ON or OFF
    ON: During control
    -
    FR Wheel EBD Ctrl Status
    Front wheel RH EBD control status / ON or OFF
    ON: During control
    -
    FL Wheel EBD Ctrl Status
    Front wheel LH EBD control status / ON or OFF
    ON: During control
    -
    RR Wheel EBD Ctrl Status
    Rear wheel RH EBD control status / ON or OFF
    ON: During control
    -
    RL Wheel EBD Ctrl Status
    Rear wheel LH EBD control status / ON or OFF
    ON: During control
    -
    BA Ctrl Status
    BA control status / ON or OFF
    ON: During control
    -
    TRC(TRAC) Ctrl Status
    TRC control status / ON or OFF
    ON: During control
    -
    TRC(TRAC) Engine Ctrl Status
    TRC engine control status / ON or OFF
    ON: During control
    -
    TRC(TRAC) Brake Ctrl Status
    TRC brake control status / ON or OFF
    ON: During control
    -
    FR Wheel VSC Ctrl Status
    Front wheel RH VSC control status / ON or OFF
    ON: During control
    -
    FL Wheel VSC Ctrl Status
    Front wheel LH VSC control status / ON or OFF
    ON: During control
    -
    RR Wheel VSC Ctrl Status
    Rear wheel RH VSC control status / ON or OFF
    ON: During control
    -
    RL Wheel VSC Ctrl Status
    Rear wheel LH VSC control status / ON or OFF
    ON: During control
    -
    Engine Revolutions
    Engine speed / Min.: 0 rpm, Max.: 65535 rpm
    Engine stopped: 0 rpm
    When engine speed is constant: No large fluctuations
    Real Engine Torque
    Real engine torque / Min.: -1024.0 Nm, Max.: 1023.0 Nm
    -
    -
    Accelerator Opening Angle %
    Percentage of accelerator pedal opening angle / Min.: 0.0%, Max.: 128.0%
    When the accelerator pedal is released: 0.0%
    During accelerator pedal operation: Changes in proportion with the pedal movement
    Solenoid Relay
    ABS solenoid relay / ON or OFF
    ON: Solenoid relay on
    OFF: Solenoid relay off
    -
    ECB* Motor Relay
    ABS motor relay / ON or OFF
    ON: Motor relay on
    OFF: Motor relay off
    -
    TR(A)C/VSC Solenoid (SRM2)
    Master cut solenoid (SRM2) / ON or OFF
    ON: Operating
    -
    TR(A)C/VSC Solenoid (SRM1)
    Master cut solenoid (SRM1) / ON or OFF
    ON: Operating
    -
    TR(A)C/VSC Solenoid (SRC2)
    Master cut solenoid (SRC2) / ON or OFF
    ON: Operating
    -
    TR(A)C/VSC Solenoid (SRC1)
    Master cut solenoid (SRC1) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SFRH)
    ABS solenoid (SFRH) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SFRR)
    ABS solenoid (SFRR) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SFLH)
    ABS solenoid (SFLH) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SFLR)
    ABS solenoid (SFLR) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SRRH)
    ABS solenoid (SRRH) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SRRR)
    ABS solenoid (SRRR) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SRLH)
    ABS solenoid (SRLH) / ON or OFF
    ON: Operating
    -
    ABS Solenoid (SRLR)
    ABS solenoid (SRLR) / ON or OFF
    ON: Operating
    -
    EFI Communication Open
    EFI communication open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    Yaw Rate Open
    Yaw rate sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    Deceleration Open
    Acceleration sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    Steering Open
    Steering angle sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    BS1 Voltage Value
    +BS voltage value / Min.: 0.00 V, Max.: 20.00 V
    -
    Changes in proportion to battery voltage
    MT Voltage Value
    Motor voltage value / Min.: 0.00 V, Max.: 20.00 V
    -
    Changes in proportion to battery voltage
    TRC/VSC Off Mode
    TRC/VSC off mode / Normal, TRC OFF, Unknown or VSC OFF
    Normal: Normal mode
    TRC OFF: TRC off mode
    Unknown: Unspecified
    VSC OFF: VSC off mode
    -
    Number of DTC
    Number of DTC recorded / Min.: 0, Max.: 255
    -
    -
    IG Voltage Value Decreased
    +BS voltage value decrease detection / Error or Normal
    Error: Voltage low
    Normal: Normal
    -
    IG Voltage Value Increased
    +BS voltage value increase detection / Error or Normal
    Error: Voltage high
    Normal: Normal
    -
    *: Electronically Controlled Brake


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts to operate without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

  7. According to the display on the tester, perform the Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ABS Warning Light
    ABS warning light
    Warning light ON/OFF
    Observe combination meter assembly
    Brake Warning Light
    Brake warning light
    Warning light ON/OFF
    Observe combination meter assembly
    Motor Relay
    ABS motor relay
    Relay ON/OFF
    Operating sound of motor can be heard
    ABS Solenoid (SRLR)
    ABS solenoid (SRLR)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SRLH)
    ABS solenoid (SRLH)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SRRR)
    ABS solenoid (SRRR)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SRRH)
    ABS solenoid (SRRH)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFLR)
    ABS solenoid (SFLR)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFLH)
    ABS solenoid (SFLH)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFRR)
    ABS solenoid (SFRR)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFRH)
    ABS solenoid (SFRH)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    VSC/TRC Solenoid (SRMR)
    Master cut solenoid (SRM2)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    VSC/TRC Solenoid (SRMF)
    Master cut solenoid (SRM1)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    VSC/TRC Solenoid (SRCR)
    Master cut solenoid (SRC2)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    VSC/TRC Solenoid (SRCF)
    Master cut solenoid (SRC1)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard
    TRC(TRAC) OFF Indicator Light
    Multi-information display (TRC OFF message)
    Display (message) ON/OFF
    Observe combination meter assembly
    VSC OFF Indicator Light
    VSC OFF indicator light
    Indicator light ON/OFF
    Observe combination meter assembly
    Slip Indicator Light
    Slip indicator light
    Indicator light ON/OFF
    Observe combination meter assembly