Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)

SMART ENTRY AND START SYSTEM (for Start Function) > TERMINALS OF ECU

for Preparation Click here



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B264892E15

  1. Disconnect the I78 and A43 connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    A43-7 (STA) - Body ground
    Input
    V - Body ground
    When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is"being started".
    20°C (68°F)
    93.75 to 136.36 Ω
    -
    A43-5 (STAR) - Body ground
    Input/Output
    P - Body ground
    Outputs voltage to the starter relay
    1. Outputs voltage (12 V) to the starter relay when starting the engine. (Max. 30 sec. Turns off when an engine speed of 500 rpm or more continues for 500 ms or more.)

    HINT:
    When Hi is selected, a start request signal (STAR) will not be output even though a start request signal (STSW) is input.

    Shift lever in any position other than P or N → shift lever in P or N (at 20°C (68°F))
    10 kΩ or higher → 93.75 to 136.36 Ω
    -
    Receives neutral start switch (P, N position detection) signal
    1. Monitors whether the neutral start switch is on (P or N) or off (other than P or N). Applies voltage via a resistor (large) in the certification ECU (smart key ECU assembly). When the neutral start switch is on, due to the starter relay coil resistance (small) using some of the voltage, the voltage at terminal STAR will be low (2.7 V or less), and when the neutral start switch is off, the voltage will be high (9 V or more).
    Perform the following operations except while the engine is cranking:
    1. Shift lever in any position other than P or N → shift lever in P or N(at 20°C (68°F))
    30 kΩ or higher → 93.75 to 136.36 Ω
    Neutral SW/ Clutch SW
    A43-16 (NE) - Body ground
    Input
    G - Body ground
    Engine speed signal
    Always
    10 kΩ or higher
    Engine Condition
    A43-9 (IG2D) - Body ground
    Output
    R - Body ground
    IG2 signal
    20°C (68°F)
    Approximately 302.97 Ω
    IG2 Relay Monitor(Outside)
    A43-18 (STP1) - Body ground
    Input
    V - Body ground
    Stop light switch signal
    Brake pedal released → Brake pedal depressed
    9 V or higher → 1 V or less
    Stop Light Switch1
    A43-2 (+B) - A43-11 (E)
    Input
    W - W
    Power source
    Always
    11 to 14 V
    -
    I78-26 (SLP) - A43-11 (E)
    Input
    P - W
    Steering lock position signal
    Always
    10 kΩ or higher
    Steering Unlock Switch
    A43-11 (E) - Body ground
    -
    W - Body ground
    GND
    Always
    Below 1 Ω
    -
    I78-30 (SSW2) - Body ground
    Input
    V - Body ground
    SSW2 contact signal

    HINT:
    Backup for SSW1. Behaves the same way as SSW1.

    Engine switch pushed → Engine switch not pushed
    Below 1 Ω → 10 kΩ or higher
    Start Switch2
    I78-28 (SSW1) - Body ground
    Input
    R - Body ground
    SSW1 contact signal
    Engine switch pushed → Engine switch not pushed
    Below 1 Ω → 10 kΩ or higher
    Start Switch1
    I78-4 (ACCD) - Body ground
    Output
    W - Body ground
    ACC signal
    20°C (68°F)
    81.49 to 118.98 Ω
    ACC Relay Monitor
    I78-6 (IG1D) - Body ground
    Output
    P - Body ground
    IG1 signal
    20°C (68°F)
    40.74 to 59.49 Ω
    IG1 Relay Monitor(Outside)
    A43-10 (CUTB) - A43-11 (E)
    Input
    L - W
    Dark current cut pin*
    Always
    11 to 14 V
    -
    I78-27 (SPD) - Body ground
    Input
    V - Body ground
    Vehicle speed signal
    Always
    30 kΩ or higher
    Vehicle Speed Signal
    1. *: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of electric waves every 0.25 seconds. that form the detection area stops).

  3. Reconnect the I78and A43connectors.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    A43-7 (STA) - A43-11 (E)
    Input
    V - W
    When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is"being started".
    With the brake pedal depressed, the engine switch is pressed and held (starter on) → After approx. 1 sec. has elapsed, the engine switch is released (starter off)
    6 V or higher*1 → 1.5 V or less
    -
    A43-5 (STAR) - A43-11 (E)
    Input/Output
    P - W
    Outputs voltage to the starter relay
    1. Outputs voltage (12 V) to the starter relay when starting the engine. (Max. 30 sec. Turns off when an engine speed of 500 rpm or more continues for 500 ms or more.)

    HINT:
    When Hi is selected, a start request signal (STAR) will not be output even though a start request signal (STSW) is input.

    With the brake pedal depressed, the engine switch is pressed and held → After approx. 1 sec. has elapsed, the engine switch is released
    6 V or higher*1 → 1.5 V or less
    -
    Receives neutral start switch (P, N position detection) signal
    1. Monitors whether the neutral start switch is on (P or N) or off (other than P or N). Applies voltage via a resistor (large) in the certification ECU (smart key ECU assembly). When the neutral start switch is on, due to the starter relay coil resistance (small) using some of the voltage, the voltage at terminal STAR will be low (2.7 V or less), and when the neutral start switch is off, the voltage will be high (9 V or more).
    Perform the following operations except while the engine is cranking:
    1. Shift lever in any position other than P or N → shift lever in P or N
    9 V or higher → 2.7 V or less
    Neutral SW/ Clutch SW
    A43-16 (NE) - A43-11 (E)
    Input
    G - W
    Engine speed signal
    Idling (engine warmed up)
    Pulse generation
    (See waveform 1)
    Engine Condition
    A43-9 (IG2D) - A43-11 (E)
    Output
    R - W
    IG2 signal
    Engine switch on (ACC) → Engine switch on (IG)
    1 V or less → 9 V or higher
    IG2 Relay Monitor(Outside)
    A43-18 (STP1) - A43-11 (E)
    Input
    V - W
    Stop light switch signal
    Brake pedal released → Brake pedal depressed
    1 V or less → 9 V or higher
    Stop Light Switch1
    I78-26 (SLP) - A43-11 (E)
    Input
    P - W
    Steering lock position signal
    Steering wheel locked → Steering wheel unlocked*2
    11 to 14 V → 1.2 V or less
    Steering Unlock Switch
    I78-29 (SLR+) - A43-11 (E)
    Output
    SB - W
    Steering lock motor operation command signal
    (Steering lock motor operation permission signal sent from the certification ECU (smart key ECU assembly))
    Steering lock motor stopped → Steering lock motor operating → Steering lock motor stopped*3
    Pulse generation
    (See waveform 2)
    -
    I78-25 (P) - A43-11 (E)
    Input
    L*4 - W
    or
    R*5 - W
    P position signal
    Shift lever in P → Shift lever not in P
    9 V or higher → 1.5 V or less
    Shift P Signal
    I78-30 (SSW2) - A43-11 (E)
    Input
    V - W
    SSW2 contact signal

    HINT:
    Backup for SSW1. Behaves the same way as SSW1.

    Engine switch not pushed → Engine switch pushed
    9 V or higher → 1 V or less
    Start Switch2
    I78-28 (SSW1) - A43-11 (E)
    Input
    R - W
    SSW1 contact signal
    Engine switch not pushed → Engine switch pushed
    9 V or higher → 1 V or less
    Start Switch1
    I78-4 (ACCD) - A43-11 (E)
    Output
    W - W
    ACC signal
    Engine switch off → Engine switch on (ACC)
    1 V or less → 8.5 V or higher
    ACC Relay Monitor
    I78-6 (IG1D) - A43-11 (E)
    Output
    P - W
    IG1 signal
    Engine switch on (ACC) → Engine switch on (IG)
    1 V or less → 9 V or higher
    IG1 Relay Monitor(Outside)
    I78-27 (SPD) - A43-11 (E)
    Input
    V - W
    Vehicle speed signal
    Vehicle being driven at approx. 5 km/h (3 mph)
    Pulse generation
    (See waveform 3)
    Vehicle Speed Signal

    HINT:
    1. *1: While the engine is cranking, the battery voltage may drop to approximately 6 V.
    2. *2: When the engine switch is turned off with the shift lever in P and any of the doors are opened or closed, the steering wheel will be locked. When the engine switch is turned on (ACC) or on (IG), the steering wheel will be unlocked.
    3. *3: When all of the following conditions are met, open any of the doors to operate the steering lock motor.
      1. The shift lever is in P.
      2. The engine switch is off.
      3. While carrying the electrical key transmitter sub-assembly, the engine switch is turned on (IG) and the steering is unlocked.
    4. *4: Except TMMK Made.
    5. *5: TMMK Made.



  5. Using an oscilloscope, check the waveform of the ECU.



      C222647E01
    1. Waveform 1
      Item
      Content
      Tester Connection
      A43-16 (NE) - A43-11 (E)
      Tool Setting
      2 V/DIV., 2 ms./DIV.
      Vehicle Condition
      Idling (engine warmed up)

      HINT:
      The wavelength becomes shorter as the engine speed increases.



    2. C221561E01
    3. Waveform 2
      Item
      Content
      Tester Connection
      I78-29 (SLR+) - A43-11 (E)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Vehicle Condition
      Steering lock motor stopped →
      Steering lock motor operating →
      Steering lock motor stopped
      Text in Illustration 
      *a
      Steering lock motor not operating
      *b
      Steering lock motor operating

      HINT:
      When all of the following conditions are met, open any of the doors to operate the steering lock motor.
      1. The shift lever is in P.
      2. While carrying the electrical key transmitter sub-assembly, the engine switch is turned on (IG) and the steering is unlocked.
      3. The engine switch is off.



    4. B220145E01
    5. Waveform 3
      Item
      Content
      Tester Connection
      I78-27 (SPD) - A43-11 (E)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Vehicle Condition
      Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

      HINT:
      The wavelength becomes shorter as the vehicle speed increases.