Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › PUSH-BUTTON START

PUSH-BUTTON START > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / (desired system) / Data List.



  5. According to the display on the GTS, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift P Signal
    Shift position P/ON or OFF
    ON: Shift lever in P
    OFF: Shift lever not in P
    1. Use this item to determine if the shift position switch is malfunctioning.
    2. The engine cannot be started when this item is OFF.
    Steering Unlock Switch
    State of steering unlock sensor signal output from steering lock actuator assembly/ON or OFF
    ON: Steering unlocked
    OFF: Steering locked
    1. When the shift lever is in P and the engine switch is off, if any door is opened then closed, the steering is locked.
    2. When the key is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks.
    3. The engine cannot be started when the steering unlock signal is off.
    Stop Light Switch1
    State of brake pedal/ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    1. Use this item to determine whether the stop light switch is malfunctioning.
    2. The engine cannot be started when this item is OFF.
    3. When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.
    Start Switch1
    Engine switch 1 status/ON or OFF
    ON: Engine switch pressed
    OFF: Engine switch not pressed
    1. If the engine switch is pressed for a short time, the display may not change.
    2. Use this item to determine whether the engine switch input signal is malfunctioning.
    Start Switch2
    Engine switch 2 status/ON or OFF
    ON: Engine switch pressed
    OFF: Engine switch not pressed
    1. Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.
    2. Behaves the same way as engine switch 1.
    Neutral SW/ Clutch SW
    Shift position (P and N)/ON or OFF
    ON: Shift lever in P or N
    OFF: Shift lever in any position other than P or N
    1. Use this item to determine whether the park/neutral position switch is malfunctioning.
    2. When the engine cannot be started due to a park/neutral position switch malfunction, OFF is displayed.
    Latch Circuit
    Status of IG related backup circuits/ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    1. Displays in almost the same manner as the IG1 and IG2 relays.
    2. When the engine switch is on (ACC), OFF is displayed.
    Starter Request Signal
    Engine start request signal status/ON or OFF
    ON: With the shift lever in P and brake pedal depressed, the engine switch is pressed and held
    OFF: After approx. 1 sec. has elapsed, the engine switch is released
    1. When the engine cannot be started due to a start request signal malfunction, OFF is displayed.
    2. When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain amount of time.
    ACC Relay Monitor
    ACC relay activation/ON or OFF
    ON: Engine switch on (ACC)
    OFF: Engine switch off
    1. When the engine switch is on (IG), ON is displayed.
    2. While the engine is cranking, OFF is displayed.
    Engine Condition
    Engine state/Stop or Run
    Stop: Engine stopped
    Run: Engine running
    -
    Vehicle Speed Signal
    Vehicle being driven or stopped/Stop or Run
    Stop: Vehicle stopped
    Run: Vehicle being driven at 5 km/h (3 mph) or more
    -
    Power Supply Condition
    Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
    All OFF: Engine switch off (ACC and IG)
    ACC ON: Engine switch on (ACC)
    IG1 ON: Engine switch on (IG) (IG1 relay on)
    IG2 ON: Engine switch on (IG) (IG2 relay on)
    ST ON: Sending engine start request signal
    Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).
    Powertrain Type
    Vehicle identification/HV-AT, Cnv-MT, Cnv-AT, Cnv-MMT, S&S-MT, S&S-AT or S&S-MMT
    Cnv-AT: Conventional A/T models (w/o hybrid system)
    -
    Starter SW Sig Mismatch
    Engine switch signal 1 and 2 do not match/Yes or No
    Yes: Switch malfunctioning (engine switch signal 1 and 2 do not match)
    No: Switch normal
    The engine can be started even if the result is Yes. However, emergency engine off while driving by pressing and holding the engine switch and, when the brakes are malfunctioning, emergency engine starting by pressing and holding the engine switch cannot be performed.
    Park Signal Mismatch
    P position signal malfunction/Yes or No
    Yes: Signal malfunction (CAN communication and direct line signal do not match)
    No: Signal normal
    Even when Yes is displayed, it is still possible to turn the engine switch off (the power source mode will not be stuck in on (ACC) or on (IG)).
    Str Lock/Unlock Wait T-Out
    Steering lock or unlock malfunction/Yes or No
    Yes: Lock or unlock malfunction (e.g. steering lock is stuck etc.)
    No: Lock and unlock normal
    When the engine cannot be started due to a steering lock or unlock malfunction, Yes is displayed.
    Key Certif Wait T-Out
    Key verification malfunction/Yes or No
    Yes: Verification error (detected due to the electrical key transmitter sub-assembly ID code and the ID code stored in the certification ECU (smart key ECU assembly) not matching)
    No: Verification normal
    When the engine cannot be started due to a key verification error, Yes is displayed.
    IG1 Relay Monitor(Outside)
    IG1 relay coil voltage monitor status/ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    1. Use this item to determine whether the IG1 relay is malfunctioning.
    2. When the engine switch is on (ACC), OFF is displayed.
    IG1 Relay Monitor(Inside)
    IG1 relay activation/ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    1. Use this item to determine whether the IG1 relay is malfunctioning.
    2. When the engine switch is on (ACC), OFF is displayed.
    IG2 Relay Monitor(Outside)
    IG2 relay coil voltage monitor status/ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    1. Use this item to determine whether the IG2 relay is malfunctioning.
    2. When the engine switch is on (ACC), OFF is displayed.
    IG2 Relay Monitor(Inside)
    IG2 relay activation/ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    1. Use this item to determine whether the IG2 relay is malfunctioning.
    2. When the engine switch is on (ACC), OFF is displayed.
    IG1 Circuit
    IG1 relay coil circuit malfunction/OK or NG
    OK: Circuit normal
    NG: Circuit malfunctioning
    1. Use this item to determine whether the IG1 relay is malfunctioning.
    2. When the engine cannot be started due to an IG1 relay malfunction, NG is displayed.
    IG2 Circuit
    IG2 relay coil circuit malfunction/OK or NG
    OK: Circuit normal
    NG: Circuit malfunctioning
    1. Use this item to determine whether the IG2 relay is malfunctioning.
    2. When the engine cannot be started due to an IG2 relay malfunction, NG is displayed.
    Number of Diagnosis Code
    Number of DTCs/0 to 255
    -
    -


    C222179E03

    HINT:
    To check if the Data List display changes, get into the vehicle while carrying an electrical key transmitter sub-assembly and perform the following operations with the engine switch off and the shift lever in P.
    *1: Press the engine switch with the brake pedal released and check that the engine switch is turned on (ACC).
    *2: Press the engine switch with the brake pedal released and check that the engine switch is turned on (IG).
    *3: Depress the brake pedal (stop light switch is on).
    *4: Press the engine switch with the brake pedal depressed and check that the engine starts.
    *5: Press the engine switch with the brake pedal depressed and check that the engine switch is turned off.
    *6: Release the brake pedal.
    *7: Open a door.


    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ignition Switch
    Certification ECU (smart key ECU assembly) IG power supply input status/ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    When the engine switch is on (ACC), OFF is displayed.
    #Codes
    Number of DTCs/0 to 255
    -
    -
    Immobiliser
    Engine immobiliser system determined by certification ECU (smart key ECU assembly)/ Set or Unset
    Set: Engine immobiliser system set (engine start prohibited) (engine switch off)
    Unset: Engine immobiliser system unset (engine start permitted) (engine switch on (ACC) or on (IG))
    The engine cannot be started when Set is displayed.

    HINT:
    1. The security indicator light blinks when Set is displayed.
    2. The security indicator light is linked with set/unset of the immobiliser and not linked with steering lock/unlock.

    Steering Lock Sleep Cond
    Steering lock ECU (steering lock actuator assembly) sleep availability/Yes or No
    Yes: Sleep available
    No: Sleep not available
    -
    Steering Lock Start Cond
    Steering lock ECU (steering lock actuator assembly) wake up signal status/Yes or No
    Yes: Wake up signal sent
    No: Wake up signal not sent
    -
    Engine Start Condition
    Status of engine start permission signal determined by steering lock ECU (steering lock actuator assembly) and sent to certification ECU (smart key ECU assembly)/OK or NG
    OK: Engine start permitted
    NG: Engine start prohibited
    1. When OK is displayed, the certification ECU (smart key ECU assembly) receives an unlock confirmation signal from the steering lock ECU (steering lock actuator assembly) and makes fuel injection and engine starting possible.
    2. The engine cannot be started when NG is displayed.
    Sensor Value
    History of malfunction of position sensor in steering lock ECU (steering lock actuator assembly)/OK or NG(Past)
    OK: History of malfunction for the lock or unlock sensor in the Steering lock ECU (steering lock actuator assembly) does not exist.
    NG(Past): History of both the lock and unlock sensors in the Steering lock ECU (steering lock actuator assembly) being on exists (Under normal operation, neither sensor is on).
    When NG (Past) is displayed, either the position sensor in the steering lock ECU (steering lock actuator assembly) or the assembly itself may be malfunctioning.
    Power Supply Short
    History of signal error (short) sent from certification ECU (smart key ECU assembly) to steering lock ECU (steering lock actuator assembly)/OK or NG(Past)
    OK: History of motor power source short does not exist
    NG(Past): History of motor power source short exists
    This item displays history when a malfunction exists in the circuit between the certification ECU (smart key ECU assembly) and the steering lock ECU (steering lock actuator assembly).
    Motor Driver Short
    History of malfunction (short) in the steering lock ECU (steering lock actuator assembly) motor circuit (DTC B2781 is stored)./OK or NG(Past)
    OK: History of short in the motor circuit does not exist
    NG(Past): History of short in the motor circuit exists
    History of a malfunction in the steering lock motor circuit in the steering lock ECU (steering lock actuator assembly).
    Lock/Unlock Receive
    History of receiving an unlock request signal/Yes or No
    Yes: History of receiving an unlock request signal exists
    No: History of receiving an unlock request signal does not exist
    -
    Lock Bar Stuck Error
    History of the steering wheel not being able to unlock properly when the steering lock operates for a certain amount of time/OK or NG(Past)
    OK: History of steering lock being stuck does not exist
    NG(Past): History of steering lock being stuck exists
    -
    Push Start Error
    History of push start malfunction due to steering lock ECU (steering lock actuator assembly)/OK or NG(Past)
    OK: History of push start malfunction does not exist
    NG(Past): History of push start malfunction exists
    -
    Engine Start Request
    Status of engine start permission signal determined by steering lock ECU (steering lock actuator assembly) and sent to certification ECU (smart key ECU assembly)/OK or NG
    OK: Signal received
    NG: Signal not received
    1. When OK is displayed, the certification ECU (smart key ECU assembly) receives an unlock confirmation signal from the steering lock ECU (steering lock actuator assembly) and makes fuel injection and engine starting possible.
    2. The engine cannot be started when NG is displayed.
    L Code Check
    Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly)/OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When NG is displayed:
    1. L code has not been registered for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly).
    2. Steering cannot be locked.
    3. Steering cannot be unlocked (the engine cannot be started).
    Unlock Request Receive
    Unlock request signal received state/OK or NG
    OK: Within 10 sec. of turning the engine switch on (IG) or on (ACC), or of an engine start operation being performed
    NG: Engine switch on (IG) or on (ACC), or engine start operation not performed
    1. The engine cannot be started when an unlock request signal cannot be received.
    2. If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
    Lock Request Receive
    Lock request signal received state/OK or NG

    HINT:
    1. The reception state is maintained for 10 seconds.
    2. When 10 seconds or more elapse after receiving the signal, the item changes to "NG".

    OK: Lock request signal received for 10 sec. of any of the doors being opened with shift lever in P and engine switch off.
    NG: Except above
    If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
    L Code Check(Past)
    Verification result history between the certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly)/OK or NG(Past)
    OK: History of abnormal verification result does not exist
    NG(Past): History of abnormal verification result exists
    -
    Steering Lock
    Steering lock ECU (steering lock actuator assembly) lock confirmation status/Set or Unset
    Set: Lock confirmed
    Unset: Lock not confirmed
    When Unset is displayed, the steering wheel is not locked.
    Steering Unlock
    Steering lock ECU (steering lock actuator assembly) unlock confirmation status/Set or Unset
    Set: Unlock confirmed
    Unset: Unlock not confirmed
    When Unset is displayed, the steering wheel is not locked (the engine cannot be started).
    Engine Start Indicator
    Smart warning light / ON or OFF
    Customization status displayed
    -

    B279857E01

    HINT:
    To check if the Data List display changes, get into the vehicle while carrying an electrical key transmitter sub-assembly and perform the following operations with the engine switch off and the shift lever in P.
    *1: Press the engine switch with the brake pedal released and check that the engine switch is turned on (ACC).
    *2: Press the engine switch with the brake pedal released and check that the engine switch is turned on (IG).
    *3: Press the engine switch and check that the engine switch is turned off.
    *4: Open any of the doors (steering locked).


    Starting Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Starter SW
    Starter operation request/ON or OFF
    ON: Starter operation requested
    OFF: Starter operation not requested
    When malfunctioning, the engine will not crank.
    Shift Position P or N
    Park/neutral position switch status/ON or OFF
    ON: Shift lever in P or N
    OFF: Shift lever in any position other than P or N
    When malfunctioning, the engine will not crank.
    Starter Relay
    Starter relay voltage monitor/ON or OFF
    ON: ST relay on
    OFF: ST relay off
    OFF is displayed when the engine cannot crank.
    Starting Control SW
    Starter request signal monitor/ON or OFF
    ON: Starting control switch on
    OFF: Starting control switch off
    When malfunctioning, the engine cannot crank.
    Ignition
    IG2 status/ON or OFF
    ON: IG2 relay on
    OFF: IG2 relay off
    -
    Engine Speed
    Engine speed/0 to 16383 r/min
    Fluctuates in accordance with engine speed
    -
    Number of DTCs
    Number of DTCs/0 to 255
    -
    -

    C222178E01

    HINT:
    *: Check that the engine starts when the engine switch is pressed with the power source mode on (IG), shift lever in P and brake pedal depressed.


    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost same as actual vehicle speed (Speedometer tester)
    -


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / (desired system) / Active Test.

  5. According to the display on the GTS, perform the Active Test.


Power Source Control 
Tester Display
Test Part
Control Range
Diagnostic Note
P Supply for Steering Lock
Smart key ECU assembly
ON/OFF

HINT:
ON: Power is supplied.
OFF: Power is not supplied.

When performing this Active Test, make sure the following condition is met:
The engine switch is on (IG).

Entry&Start 
Tester Display
Test Part
Control Range
Diagnostic Note
Power/Engine SW Light
Engine switch light
OFF/ON
When performing this Active Test, make sure the following condition is met:
The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the engine switch is on (ACC) or on (IG), or the engine is running.

Starting Control 
Tester Display
Test Part
Control Range
Diagnostic Note
Activate the Starter Relay
ST relay
OFF/ON
The electrical key transmitter sub-assembly is in the cabin and the engine is stopped.