Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function)

SMART ENTRY AND START SYSTEM (for Entry Function) > Key Luggage Compartment Lock-in Prevention Function does not Operate

for Preparation Click here


DESCRIPTION

If the entry luggage compartment lock-in prevention function does not operate, there may be a problem with the communication between the No. 3 indoor electrical key antenna assembly (inside luggage compartment) and electrical key transmitter sub-assembly, wave interference or a malfunction in the certification ECU (smart key ECU assembly).

WIRING DIAGRAM


B282017E16


INSPECTION PROCEDURE

NOTICE:
  1. The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the engine switch off to troubleshoot:
    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (Click here).
  6. After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

1.CHECK ENTRY FUNCTION (ENTRY LUGGAGE COMPARTMENT OPEN FUNCTION)
  1. Check that the entry luggage compartment open function operates (Click here).

    Result:
    Result
    Proceed to
    Entry luggage compartment door open function operates
    A
    Entry luggage compartment door open function does not operate
    B



B
GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table) (Click here)
A


2.CHECK WAVE ENVIRONMENT


    B364801E01
  1. Bring the electrical key transmitter sub-assembly near the No. 3 indoor electrical key antenna assembly (inside luggage compartment), and check that the entry luggage compartment lock-in prevention function operates.
    Text in Illustration 
    *A
    for Type A
    *B
    for Type B
    *a
    Inspection Point

    NOTICE:
    If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the No. 3 indoor electrical key antenna assembly (inside luggage compartment), communication is not possible.

    HINT:
    1. When the electrical key transmitter sub-assembly is brought near the No. 3 indoor electrical key antenna assembly (inside luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Entry functions operate normally.



NG
Go to step 3
OK

AFFECTED BY WAVE INTERFERENCE 

3.CHECK KEY DIAGNOSTIC MODE
  1. Check the following antennas in the key diagnostic mode (Click here).



    B364801E01
  1. Select either channel 1 or channel 2 and inspect the key diagnostic mode for each channel.
    Text in Illustration 
    *A
    for Type A
    *B
    for Type B
    *a
    Inspection Point

    1. When the electrical key transmitter sub-assembly is held at the same height as the rear bumper upper surface and aligned with the center of the rear of the vehicle, check that the wireless door lock buzzer sounds.

      HINT:
      1. Place the key in the luggage area.
      2. If the buzzer sounds, it can be determined that the No. 3 indoor electrical key antenna assembly (inside luggage compartment) is operating normally.
      3. If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

      OK:
      Wireless door lock buzzer sounds.



NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 3 INDOOR ELECTRICAL KEY ANTENNA)
  1. Disconnect the O1 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the N38 No. 3 indoor electrical key antenna assembly (inside luggage compartment) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    except TMMK Made 
    Tester Connection
    Condition
    Specified Condition
    O1-9 (CLG7) - N38-1 (CLG6)
    Always
    Below 1 Ω
    O1-8 (CG7B) - N38-3 (CLGB)
    Always
    Below 1 Ω
    O1-9 (CLG7) or N38-1 (CLG6) - Body ground
    Always
    10 kΩ or higher
    O1-8 (CG7B) or N38-3 (CLGB) - Body ground
    Always
    10 kΩ or higher
    for TMMK Made 
    Tester Connection
    Condition
    Specified Condition
    O1-9 (CLG7) - N38-1 (ANTE7)
    Always
    Below 1 Ω
    O1-8 (CG7B) - N38-3 (CLGB)
    Always
    Below 1 Ω
    O1-9 (CLG7) or N38-1 (ANTE7) - Body ground
    Always
    10 kΩ or higher
    O1-8 (CG7B) or N38-3 (CLGB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Connect the N38 certification ECU (smart key ECU assembly) connector.



    B282018E32
  1. Measure the voltage according to the value(s) in the table below.


OK:
except TMMK Made 
Tester Connection
Switch Condition
Tool Setting
Specified Condition
N38-1 (CLG6) - N38-3 (CLGB)
Procedure:
  1. Engine switch off
  2. Electrical key transmitter sub-assembly not inside vehicle
  3. All doors closed
  4. Driver door lock sensor not touched → touched
2 V/DIV., 500 ms/DIV.
Pulse generation (See waveform)
for TMMK Made 
Tester Connection
Switch Condition
Tool Setting
Specified Condition
N38-1 (ANTE7) - N38-3 (CLGB)
Procedure:
  1. Engine switch off
  2. Electrical key transmitter sub-assembly not inside vehicle
  3. All doors closed
  4. Driver door lock sensor not touched → touched
2 V/DIV., 500 ms/DIV.
Pulse generation (See waveform)

Text in Illustration 
*A
except TMMK Made
*B
for TMMK Made
*1
Waveform
*a
Front view of wire harness connector
(to No. 3 Indoor Electrical Key Antenna Assembly (inside luggage compartment))
*b
Driver door lock sensor not touched
*c
Driver door lock sensor touched


NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


6.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)
  1. Replace the No. 3 indoor electrical key antenna assembly (inside luggage compartment) (Click here).


NEXT


7.CHECK NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)
  1. Check that the entry luggage compartment lock-in prevention function operates normally (Click here).

    OK:
    Entry luggage compartment lock-in prevention function operates normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT) WAS DEFECTIVE