Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. Turn the ignition switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.
  3. Turn the ignition switch off before inspecting CAN bus lines for a ground short.
  4. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  5. This section describes the standard values for all CAN related components.

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


CAN NO. 1 JUNCTION CONNECTOR (for LHD except TMMR Made)


  1. Check the CAN No. 1 junction connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.




    1. Connection diagram


      C239444E11


      Text in Illustration 
      *a
      Component with harness connected
      (CAN No. 1 Junction Connector)
      *b
      to AFS ECU*
      (for V Bus)
      *c
      to Main Body ECU (Multiplex Network Body ECU)
      (for V Bus)
      *d
      to Steering Sensor
      (for V Bus)
      *e
      to Airbag Sensor Assembly
      (for V Bus)
      *f
      to DLC3
      (for V Bus)
      *g
      to Power Steering ECU with Motor Assembly
      (for V Bus)
      *h
      to Combination Meter Assembly
      (for V Bus)
      *i
      to CAN No. 2 Junction Connector
      (for V Bus)
      -
      -
      *: w/ AFS

    2. Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I112-1 (CANH)
      BE
      AFS ECU*
      (for V bus)
      I112-2 (CANL)
      W
      I95-1 (CANH)
      P
      Main body ECU (Multiplex network body ECU)
      (for V bus)
      I95-2 (CANL)
      W
      I97-1 (CANH)
      V
      Steering sensor
      (for V bus)
      I97-2 (CANL)
      W
      I103-1 (CANH)
      Y
      Airbag sensor assembly
      (for V bus)
      I103-2 (CANL)
      W
      I96-1 (CANH)
      L
      DLC3
      (for V bus)
      I96-2 (CANL)
      W
      I100-1 (CANH)
      G
      Power steering ECU with motor assembly
      (for V bus)
      I100-2 (CANL)
      W
      I94-1 (CANH)
      R
      Combination meter assembly
      (for V bus)
      I94-2 (CANL)
      W
      I93-1 (CANH)
      B
      CAN No. 2 junction connector
      (for V bus)
      I93-2 (CANL)
      W
      *: w/ AFS


CAN NO. 1 JUNCTION CONNECTOR (for LHD TMMR Made)


  1. Check the CAN No. 1 junction connector.



    1. Connection diagram


      C283770E03


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN No. 1 Junction Connector)
      *b
      to AFS ECU*1
      (for V Bus)
      *c
      to Combination Meter Assembly
      (for V Bus)
      *d
      to Main Body ECU (Multiplex Network Body ECU)
      (for V Bus)
      *e
      to DLC3
      (for V Bus)
      *f
      to Steering Sensor
      (for V Bus)
      *g
      to Airbag Sensor Assembly
      (for V Bus)
      *h
      to Power Steering ECU with Motor Assembly
      (for V Bus)
      *i
      to Inner Rear View Mirror Assembly*2
      (for V Bus)
      *j
      to CAN No. 2 Junction Connector
      (for V Bus)
      1. *1: w/ AFS
      2. *2: w/ Automatic High Beam System

    2. Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I198-1 (CANH)
      BE
      AFS ECU*1
      (for V bus)
      I198-11 (CANL)
      W
      I198-2 (CANH)
      R
      Combination meter assembly
      (for V bus)
      I198-12 (CANL)
      W
      I198-3 (CANH)
      P
      Main body ECU (Multiplex network body ECU)
      (for V bus)
      I198-13 (CANL)
      W
      I198-4 (CANH)
      L
      DLC3
      (for V bus)
      I198-14 (CANL)
      W
      I198-5 (CANH)
      V
      Steering sensor
      (for V bus)
      I198-15 (CANL)
      W
      I198-6 (CANH)
      Y
      Airbag sensor assembly
      (for V bus)
      I198-16 (CANL)
      W
      I198-7 (CANH)
      G
      Power steering ECU with motor assembly
      (for V bus)
      I198-17 (CANL)
      W
      I198-8 (CANH)
      R
      Inner rear view mirror assembly*2
      (for V bus)
      I198-18 (CANL)
      W
      I198-10 (CANH)
      B
      CAN No. 2 junction connector
      (for V bus)
      I198-20 (CANL)
      W

      1. *1: w/ AFS
      2. *2: w/ Automatic High Beam System


CAN NO. 1 JUNCTION CONNECTOR (for RHD)


  1. Check the CAN No. 1 junction connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.




    1. Connection diagram


      C250922E03


      Text in Illustration 
      *a
      Component with harness connected
      (CAN No. 1 Junction Connector)
      *b
      to Main Body ECU (Multiplex Network Body ECU)
      (for V Bus)
      *c
      to Air Conditioning Amplifier Assembly
      (for V Bus)
      *d
      to Airbag Sensor Assembly
      (for V Bus)
      *e
      to Power Steering ECU with Motor Assembly
      (for V Bus)
      *f
      to ECM
      (for V Bus)
      *g
      to Radio and Display Receiver Assembly*
      (for V Bus)
      *h
      to CAN No. 2 Junction Connector
      (for V Bus)
      *: for Radio and Display Type

    2. Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I95-1 (CANH)
      P
      Main body ECU (Multiplex network body ECU)
      (for V bus)
      I95-2 (CANL)
      W
      I102-1 (CANH)
      V
      Air conditioning amplifier assembly
      (for V bus)
      I102-2 (CANL)
      W
      I103-1 (CANH)
      Y
      Airbag sensor assembly
      (for V bus)
      I103-2 (CANL)
      W
      I100-1 (CANH)
      L
      Power steering ECU with motor assembly
      (for V bus)
      I100-2 (CANL)
      W
      I104-1 (CANH)
      G
      ECM
      (for V bus)
      I104-2 (CANL)
      W
      I107-1 (CANH)
      R
      Radio and display receiver assembly*
      (for V bus)
      I107-2 (CANL)
      W
      I93-1 (CANH)
      B
      CAN No. 2 junction connector
      (for V bus)
      I93-2 (CANL)
      W
      *: for Radio and Display Type


CAN NO. 2 JUNCTION CONNECTOR (for LHD)


  1. Check the CAN No. 2 junction connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.




    1. Connection diagram


      C239444E12


      Text in Illustration 
      *a
      Component with harness connected
      (CAN No. 2 Junction Connector)
      *b
      to Clearance Warning ECU Assembly*1
      (for V Bus)
      *c
      to ECM
      (for V Bus)
      *d
      to Air Conditioning Amplifier Assembly
      (for V Bus)
      *e
      to Brake Actuator Assembly
      (for V Bus)
      *f
      to Smart Key ECU Assembly (Certification ECU)*2
      (for V Bus)
      *g
      to Network Gateway ECU*3
      (for V Bus)
      *h
      1. to Navigation receiver assembly*4
      2. to Radio and Display Receiver Assembly*5
      (for V Bus)
      *i
      to CAN No. 1 Junction Connector
      (for V Bus)
      -
      -
      1. *1: w/ Toyota Parking Assist-sensor System
      2. *2: w/ Smart Entry and Start System
      3. *3: w/ Network Gateway ECU
      4. *4: for Navigation Receiver Type
      5. *5: for Radio and Display Type

    2. Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I111-1 (CANH)
      BE
      Clearance warning ECU assembly*1
      (for V bus)
      I111-2 (CANL)
      W
      I104-1 (CANH)
      P
      ECM
      (for V bus)
      I104-2 (CANL)
      W
      I102-1 (CANH)
      V
      Air conditioning amplifier assembly
      (for V bus)
      I102-2 (CANL)
      W
      I105-1 (CANH)
      Y
      Brake actuator assembly
      (for V bus)
      I105-2 (CANL)
      W
      I106-1 (CANH)
      L
      Smart key ECU assembly (Certification ECU)*2
      (for V bus)
      I106-2 (CANL)
      W
      I188-1 (CANH)
      G
      Network gateway ECU*3
      (for V bus)
      I188-2 (CANL)
      W
      I107-1 (CANH)
      R
      1. Navigation receiver assembly*4
      2. Radio and display receiver assembly*5
      (for V bus)
      I107-2 (CANL)
      W
      I101-1 (CANH)
      B
      CAN No. 1 junction connector
      (for V bus)
      I101-2 (CANL)
      W

      1. *1: w/ Toyota Parking Assist-sensor System
      2. *2: w/ Smart Entry and Start System
      3. *3: w/ Network Gateway ECU
      4. *4: for Navigation Receiver Type
      5. *5: for Radio and Display Type


CAN NO. 2 JUNCTION CONNECTOR (for RHD)


  1. Check the CAN No. 2 junction connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.




    1. Connection diagram


      C269150E02


      Text in Illustration 
      *a
      Component with harness connected
      (CAN No. 2 Junction Connector)
      *b
      to Clearance Warning ECU Assembly
      (for V Bus)
      *c
      to Steering Sensor
      (for V Bus)
      *d
      to Brake Actuator Assembly
      (for V Bus)
      *e
      to Smart Key ECU Assembly (Certification ECU)
      (for V Bus)
      *f
      DLC3
      (for V Bus)
      *g
      to Combination Meter Assembly
      (for V Bus)
      *h
      to CAN No. 1 Junction Connector
      (for V Bus)

    2. Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I111-1 (CANH)
      P
      Clearance warning ECU assembly
      (for V bus)
      I111-2 (CANL)
      W
      I97-1 (CANH)
      V
      Steering sensor
      (for V bus)
      I97-2 (CANL)
      W
      I105-1 (CANH)
      Y
      Brake actuator assembly
      (for V bus)
      I105-2 (CANL)
      W
      I106-1 (CANH)
      L
      Smart key ECU assembly (Certification ECU)
      (for V bus)
      I106-2 (CANL)
      W
      I96-1 (CANH)
      G
      DLC3
      (for V bus)
      I96-2 (CANL)
      W
      I94-1 (CANH)
      R
      Combination meter assembly
      (for V bus)
      I94-2 (CANL)
      W
      I101-1 (CANH)
      B
      CAN No. 1 junction connector
      (for V bus)
      I101-2 (CANL)
      W


CAN NO. 3 JUNCTION CONNECTOR (for LHD TMC Made)


  1. Check the CAN No. 3 junction connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.




    1. Connection diagram


      C311618E01


      Text in Illustration 
      *a
      Component with harness connected
      (CAN No. 3 Junction Connector)
      *b
      to Multiplex Tilt and Telescopic ECU*
      (for Sub Bus 1)
      *c
      to Main Body ECU (Multiplex Network Body ECU)
      (for Sub Bus 1)
      *d
      to CAN No. 4 Junction Connector
      (for Sub Bus 1)
      1. *: w/ Power Tilt and Power Telescopic Steering Column System

    2. Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I115-1 (CANH)
      B
      Multiplex tilt and telescopic ECU*
      (for Sub bus 1)
      I115-2 (CANL)
      GR
      I114-1 (CANH)
      R
      Main body ECU (Multiplex network body ECU)
      (for Sub bus 1)
      I114-2 (CANL)
      GR
      I117-1 (CANH)
      Y
      CAN No. 4 junction connector
      (for Sub bus 1)
      I117-2 (CANL)
      GR

      1. *: w/ Power Tilt and Power Telescopic Steering Column System


CAN NO. 3 JUNCTION CONNECTOR (for LHD TMMR Made)


  1. Check the CAN No. 3 junction connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.




    1. Connection diagram


      C311619E01


      Text in Illustration 
      *a
      Component with harness connected
      (CAN No. 3 Junction Connector)
      *b
      to Main Body ECU (Multiplex Network Body ECU)
      (for Sub Bus 1)
      *c
      to Multiplex Tilt and Telescopic ECU*1
      (for Sub Bus 1)
      *d
      to CAN No. 4 Junction Connector
      (for Sub Bus 1)
      *e
      to Outer Mirror Control ECU Assembly (for Driver Side)*2
      (for Sub Bus 1)
      *f
      to Position Control ECU and Switch Assembly (for Driver Side)*2
      (for Sub Bus 1)
      1. *1: w/ Power Tilt and Power Telescopic Steering Column System
      2. *2: w/ Seat Position Memory System

    2. Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I114-1 (CANH)
      R
      Main body ECU (Multiplex network body ECU)
      (for Sub bus 1)
      I114-2 (CANL)
      GR
      I115-1 (CANH)
      B
      Multiplex tilt and telescopic ECU*1
      (for Sub bus 1)
      I115-2 (CANL)
      GR
      I117-1 (CANH)
      Y
      CAN No. 4 junction connector
      (for Sub bus 1)
      I117-2 (CANL)
      GR
      I199-1 (CANH)
      G
      Outer mirror control ECU assembly (for Driver side)*2
      (for Sub bus 1)
      I199-2 (CANL)
      GR
      I201-1 (CANH)
      L
      Position control ECU and switch assembly (for Driver side)*2
      (for Sub bus 1)
      I201-2 (CANL)
      GR

      1. *1: w/ Power Tilt and Power Telescopic Steering Column System
      2. *2: w/ Seat Position Memory System


CAN NO. 4 JUNCTION CONNECTOR (for LHD)


  1. Check the CAN No. 4 junction connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.




    1. Connection diagram


      C310684E01


      Text in Illustration 
      *a
      Component with harness connected
      (CAN No. 4 Junction Connector)
      *b
      to Outer Mirror Control ECU Assembly (for Front Passenger Side)*
      (for Sub Bus 1)
      *c
      to CAN No. 5 Junction Connector
      (for Sub Bus 1)
      *d
      to CAN No. 3 Junction Connector
      (for Sub Bus 1)
      1. *: w/ Seat Position Memory System

    2. Check the connection diagram of the components which are connected to the CAN No. 4 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I200-1 (CANH)
      P
      Outer mirror control ECU assembly (for Front passenger side)*
      (for Sub bus 1)
      I200-2 (CANL)
      GR
      I121-1 (CANH)
      V
      CAN No. 5 junction connector
      (for Sub bus 1)
      I121-2 (CANL)
      GR
      I120-1 (CANH)
      Y
      CAN No. 3 junction connector
      (for Sub bus 1)
      I120-2 (CANL)
      GR

      1. *: w/ Seat Position Memory System


CAN NO. 5 JUNCTION CONNECTOR (for LHD)


  1. Check the CAN No. 5 junction connector.



      C183982E18
    1. Connection diagram
      Text in Illustration 
      *a
      Rear view of wire harness connector
      (to CAN No. 5 Junction Connector)
      *b
      to CAN No. 4 Junction Connector
      (for Sub Bus 1)

    2. Check the connection diagram of the components which are connected to the CAN No. 5 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I123-3 (CANH)
      V
      CAN No. 4 junction connector
      (for Sub bus 1)
      I123-2 (CANL)
      GR


CAN NO. 6 JUNCTION CONNECTOR (for LHD)


  1. Check the CAN No. 6 junction connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.




    1. Connection diagram


      C249351E03


      Text in Illustration 
      *1
      CAN No. 6 Junction Connector
      -
      -
      *a
      Junction Connector A Side
      *b
      Junction Connector B Side
      *c
      Earth Terminal
      *d
      Front view of wire harness connector
      (to CAN No. 6 Junction Connector)

    2. Check the connection diagram of the components which are connected to the CAN No. 6 junction connector.

      Junction Connector B Side 
      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I190-1 (CANH)
      V
      CAN No. 7 junction connector
      (for Sub bus 2)
      I190-2 (CANL)
      LG
      I189-1 (CANH)
      B
      Network gateway ECU*
      (for Sub bus 2)
      I189-2 (CANL)
      LG

      1. *: w/ Network Gateway ECU


CAN NO. 7 JUNCTION CONNECTOR (for LHD)


  1. Check the CAN No. 7 junction connector.



      C238890E60
    1. Connection diagram
      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN No. 7 Junction Connector)
      *b
      to CAN No. 8 Junction Connector
      (for Sub Bus 2)
      *c
      to Blind Spot Monitor Sensor RH*
      (for Sub Bus 2)
      *d
      to CAN No. 6 Junction Connector
      (for Sub Bus 2)

      1. *: w/ Blind Spot Monitor Sensor

    2. Check the connection diagram of the components which are connected to the CAN No. 7 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      O44-8 (CANH)
      G
      CAN No. 8 junction connector
      (for Sub bus 2)
      O44-19 (CANL)
      B
      O44-9 (CANH)
      R
      Blind spot monitor sensor RH*
      (for Sub bus 2)
      O44-20 (CANL)
      B
      O44-11 (CANH)
      V
      CAN No. 6 junction connector
      (for Sub bus 2)
      O44-22 (CANL)
      B

      1. *: w/ Blind Spot Monitor Sensor


CAN NO. 8 JUNCTION CONNECTOR (for LHD)


  1. Check the CAN No. 8 junction connector.



      C238890E67
    1. Connection diagram
      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN No. 8 Junction Connector)
      *b
      to CAN No. 9 Junction Connector
      (for Sub Bus 2)
      *c
      to Rear Television Camera Assembly*
      (for Sub Bus 2)
      *d
      to CAN No. 7 Junction Connector
      (for Sub Bus 2)

      1. *: for Radio and Display Type (w/ Parking Assist Monitor System without Parallel Parking Assist Function)

    2. Check the connection diagram of the components which are connected to the CAN No. 8 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      T21-1 (CANH)
      L
      CAN No. 9 junction connector
      (for Sub bus 2)
      T21-12 (CANL)
      B
      T21-2 (CANH)
      V
      Rear television camera assembly*
      (for Sub bus 2)
      T21-13 (CANL)
      P
      T21-3 (CANH)
      G
      CAN No. 7 junction connector
      (for Sub bus 2)
      T21-14 (CANL)
      B

      1. *: for Radio and Display Type (w/ Parking Assist Monitor System without Parallel Parking Assist Function)


CAN NO. 9 JUNCTION CONNECTOR (for LHD)


  1. Check the CAN No. 9 junction connector.



      C183982E61
    1. Connection diagram
      Text in Illustration 
      *a
      Rear view of wire harness connector
      (to CAN No. 9 Junction Connector)
      *b
      to CAN No. 8 Junction Connector
      (for Sub Bus 2)

    2. Check the connection diagram of the components which are connected to the CAN No. 9 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      T22-3 (CANH)
      L
      CAN No. 8 junction connector
      (for Sub bus 2)
      T22-2 (CANL)
      B


DLC3
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Measure the resistance according to the value(s) in the table below.


    C188081E32


    Text in Illustration 
    *1
    DLC3
    -
    -

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    L - W*1
    G - W*2
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I39-6 (CANH) - I39-4 (CG)
    L - W-B*1
    G - W-B*2
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I39-14 (CANL) - I39-4 (CG)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I39-6 (CANH) - I39-16 (BAT)
    L - R*1
    G - R*2
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I39-14 (CANL) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    *1: for LHD
    *2: for RHD


ECM (for 2GR-FE)

A247842E55


Text in Illustration 
*a
Component without harness connected
(ECM)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the A25 and E26 ECM connectors.


    C239445E15


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A25-13 (CANH) - A25-26 (CANL)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    A25-13 (CANH) - E26-49 (E1)
    B - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A25-26 (CANL) - E26-49 (E1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A25-13 (CANH) - A25-1 (BATT)
    B - GR
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A25-26 (CANL) - A25-1 (BATT)
    W - GR
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


ECM (for 2AR-FE)

A247842E63


Text in Illustration 
*a
Component without harness connected
(ECM)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the A25 and E26 ECM connectors.


    C239445E18


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A25-13 (CANH) - A25-26 (CANL)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    A25-13 (CANH) - E26-16 (E1)
    B - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A25-26 (CANL) - E26-16 (E1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A25-13 (CANH) - A25-1 (BATT)
    B - GR
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A25-26 (CANL) - A25-1 (BATT)
    W - GR
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


ECM (for 6AR-FSE)

A247842E62


Text in Illustration 
*a
Component without harness connected
(ECM)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the A84 and E96 ECM connectors.


    C326519E01


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A84-13 (CANH) - A84-26 (CANL)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    A84-13 (CANH) - E96-53 (E1)
    B - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A84-26 (CANL) - E96-53 (E1)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A84-13 (CANH) - A84-1 (BATT)
    B - GR
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A84-26 (CANL) - A84-1 (BATT)
    W - GR
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


COMBINATION METER ASSEMBLY

E224288E10


Text in Illustration 
*a
Component without harness connected
(Combination Meter Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. E224284E33
  3. Disconnect the I18 combination meter assembly connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I18-17 (CANH) - I18-16 (CANL)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    I18-17 (CANH) - I18-20 (ES)
    R - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I18-16 (CANL) - I18-20 (ES)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I18-17 (CANH) - I18-1 (B)
    R - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I18-16 (CANL) - I18-1 (B)
    W - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B278841E61


Text in Illustration 
*A
for LHD
*B
for RHD
*a
Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the I12 and I13 main body ECU (multiplex network body ECU) connectors.


    C204058E19


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Main Body ECU (Multiplex Network Body ECU))
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    V Bus Branch Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I13-14 (CANH) - I13-13 (CANL)
    P - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I13-14 (CANH) - I39-4 (CG)
    P - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I13-13 (CANL) - I39-4 (CG)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I13-14 (CANH) - I39-16 (BAT)
    P - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I13-13 (CANL) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    Sub Bus 1 Main Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I12-9 (CANP) - I12-10 (CANN)
    R - GR
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    I12-9 (CANP) - I39-4 (CG)
    R - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I12-10 (CANN) - I39-4 (CG)
    GR - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I12-9 (CANP) - I39-16 (BAT)
    R - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I12-10 (CANN) - I39-16 (BAT)
    GR - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


BRAKE ACTUATOR ASSEMBLY

C238830E06


Text in Illustration 
*a
Component without harness connected
(Brake Actuator Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. C238832E52
  3. Disconnect the A49 brake actuator assembly connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly)

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A49-26 (CANH) - A49-14 (CANL)
    GR - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    A49-26 (CANH) - A49-38 (GND1)
    GR - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A49-14 (CANL) - A49-38 (GND1)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A49-26 (CANH) - A49-25 (+BS)
    GR - L
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A49-14 (CANL) - A49-25 (+BS)
    W - L
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


STEERING SENSOR
  1. Disconnect the cable from the negative (-) battery terminal.



  2. C156493E53
  3. Disconnect the I29 steering sensor connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Sensor)

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I29-3 (CANH) - I29-2 (CANL)
    V - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I29-3 (CANH) - I29-1 (ESS)
    V - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I29-2 (CANL) - I29-1 (ESS)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I29-3 (CANH) - I29-5 (BAT)
    V - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I29-2 (CANL) - I29-5 (BAT)
    W - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


POWER STEERING ECU WITH MOTOR ASSEMBLY

C238935E09


Text in Illustration 
*a
Component without harness connected
(Power Steering ECU with Motor Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the j1 and j2 power steering ECU with motor assembly connectors.


    C240488E15


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU with Motor Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    j1-7 (CANH) - j1-8 (CANL)
    Y - SB
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    j1-7 (CANH) - j2-2 (PGND)
    Y - B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    j1-8 (CANL) - j2-2 (PGND)
    SB - B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    j1-7 (CANH) - j2-1 (PIG)
    Y - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    j1-8 (CANL) - j2-1 (PIG)
    SB - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


AIRBAG SENSOR ASSEMBLY
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the I47 airbag sensor assembly connector.


    C188802E40


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I47-13 (CANH) - I47-22 (CANL)
    Y - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I47-13 (CANH) - I47-25 (E1)
    Y - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I47-22 (CANL) - I47-25 (E1)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I47-13 (CANH) - I39-16 (BAT)
    Y - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I47-22 (CANL) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


SMART KEY ECU ASSEMBLY (CERTIFICATION ECU) (w/ Smart Entry and Start System)

B264892E81


Text in Illustration 
*a
Component without harness connected
(Smart Key ECU Assembly (Certification ECU))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the A43 and I78 smart key ECU assembly (certification ECU) connectors.


    C240482E09


    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Smart Key ECU Assembly (Certification ECU))
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I78-14 (CANH) - I78-15 (CANL)
    L - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I78-14 (CANH) - A43-11 (E)
    L - W
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I78-15 (CANL) - A43-11 (E)
    W - W
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I78-14 (CANH) - A43-2 (+B)
    L - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I78-15 (CANL) - A43-2 (+B)
    W - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)

E296380E05


Text in Illustration 
*a
Component without harness connected
(Radio and Display Receiver Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the I152 and I155 radio and display receiver assembly connectors.


    C240506E52


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I155-9 (CANH) - I155-10 (CANL)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I155-9 (CANH) - I152-7 (GND1)
    R - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I155-10 (CANL) - I152-7 (GND1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I155-9 (CANH) - I152-4 (+B1)
    R - L-Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I155-10 (CANL) - I152-4 (+B1)
    W - L-Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Parking Assist Monitor System without Parallel Parking Assist Function))

E277820E03


Text in Illustration 
*a
Component without harness connected
(Radio and Display Receiver Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the I152 and I155 radio and display receiver assembly connectors.


    C240506E52


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I155-9 (CANH) - I155-10 (CANL)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I155-9 (CANH) - I152-7 (GND1)
    R - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I155-10 (CANL) - I152-7 (GND1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I155-9 (CANH) - I152-4 (+B1)
    R - L-Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I155-10 (CANL) - I152-4 (+B1)
    W - L-Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)

E277812E11


Text in Illustration 
*a
Component without harness connected
(Navigation receiver assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the I64 and I67 navigation receiver assembly connectors.


    C240506E53


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I67-9 (CANH) - I67-10 (CANL)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I67-9 (CANH) - I64-7 (GND1)
    R - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I67-10 (CANL) - I64-7 (GND1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I67-9 (CANH) - I64-4 (+B1)
    R - L-Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I67-10 (CANL) - I64-4 (+B1)
    W - L-Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER ASSEMBLY

E226604E22


Text in Illustration 
*a
Component without harness connected
(Air Conditioning Amplifier Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the I77 air conditioning amplifier assembly connector.


    C188799E51


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I77-11 (CANH) - I77-12 (CANL)
    V - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I77-11 (CANH) - I77-14 (GND)
    V - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I77-12 (CANL) - I77-14 (GND)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I77-11 (CANH) - I77-21 (B)
    V - Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I77-12 (CANL) - I77-21 (B)
    W - Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


CLEARANCE WARNING ECU ASSEMBLY (w/ Toyota Parking Assist-sensor System)
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the I82 clearance warning ECU assembly connector.


    C240483E15


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Clearance Warning ECU Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I82-17 (R1) - I82-18 (R2)
    BE - W*1
    P - W*2
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I82-17 (R1) - I82-30 (E)
    BE - BR*1
    P - BR*2
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I82-18 (R2) - I82-30 (E)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I82-17 (R1) - I39-16 (BAT)
    BE - R*1
    P - R*2
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I82-18 (R2) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    *1: for LHD
    *2: for RHD


AFS ECU (w/ AFS)

C188112E08


Text in Illustration 
*a
Component without harness connected
(AFS ECU)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the A35 AFS ECU connector.


    C188932E21


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to AFS ECU)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A35-12 (MPX1) - A35-13 (MPX2)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    A35-12 (MPX1) - A35-22 (E1)
    B - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A35-13 (MPX2) - A35-22 (E1)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A35-12 (MPX1) - I39-16 (BAT)
    B - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A35-13 (MPX2) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


MULTIPLEX TILT AND TELESCOPIC ECU (w/ Power Tilt and Power Telescopic Steering Column System)

C240520E14


Text in Illustration 
*a
Component without harness connected
(Multiplex Tilt and Telescopic ECU)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the I15 multiplex tilt and telescopic ECU connector.


    C241674E07


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I15-3 (CANP) -I15-11 (CANN)
    B - GR
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I15-3 (CANP) - I15-1 (GND)
    B - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I15-11 (CANN) - I15-1 (GND)
    GR - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I15-3 (CANP) - I15-2 (+B)
    B - Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I15-11 (CANN) - I15-2 (+B)
    GR - Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


INNER REAR VIEW MIRROR ASSEMBLY (w/ Automatic High Beam System)

C310791E01


Text in Illustration 
*a
Component without harness connected
(Inner Rear View Mirror Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the S2 inner rear view mirror assembly connector.


    C310792E01


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Inner Rear View Mirror Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S2-3 (CANH) -S2-2 (CANL)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    S2-3 (CANH) - S2-1 (E)
    R - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    S2-2 (CANL)- S2-1 (E)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    S2-3 (CANH) - I39-16 (BAT)
    R - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    S2-2 (CANL) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


NETWORK GATEWAY ECU (w/ Network Gateway ECU)

C238891E08


Text in Illustration 
*a
Component without harness connected
(Network Gateway ECU)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. C238892E66
  3. Disconnect the I187 network gateway ECU connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Network Gateway ECU)

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    V Bus Branch Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I187-16 (CA1H) - I187-15 (CA1L)
    G - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I187-16 (CA1H) - I187-4 (GND)
    G - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I187-15 (CA1L) - I187-4 (GND)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I187-16 (CA1H) - I187-2 (BATT)
    G - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I187-15 (CA1L) - I187-2 (BATT)
    W - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    Sub Bus 2 Main Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I187-13 (CA2H) - I187-12 (CA2L)
    B - LG
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    I187-13 (CA2H) - I187-4 (GND)
    B - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I187-12 (CA2L) - I187-4 (GND)
    LG - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I187-13 (CA2H) - I187-2 (BATT)
    B - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I187-12 (CA2L) - I187-2 (BATT)
    LG - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


REAR TELEVISION CAMERA ASSEMBLY (for Radio and Display Type (w/ Parking Assist Monitor System without Parallel Parking Assist Function))

C302330E05


Text in Illustration 
*a
Component without harness connected
(Rear Television Camera Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the T20 rear television camera assembly connector.


    C295280E05


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Rear Television Camera Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T20-4 (CANH) - T20-1 (CANL)
    V - P
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    T20-4 (CANH) - I39-4 (CG)
    V - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    T20-1 (CANL) - I39-4 (CG)
    P - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    T20-4 (CANH) - I39-16 (BAT)
    V - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    T20-1 (CANL) - I39-16 (BAT)
    P - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side) (w/ Seat Position Memory System)

B381655E05


Text in Illustration 
*a
Component without harness connected
(Outer Mirror Control ECU Assembly (for Driver Side))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. C262706E50
  3. Disconnect the K12 outer mirror control ECU assembly (for driver side) connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Outer Mirror Control ECU Assembly (for Driver Side))

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K12-9 (CANP) - K12-8 (CANN)
    G - GR
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    K12-9 (CANP) - K12-7 (GND)
    G - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    K12-8 (CANN) - K12-7 (GND)
    GR - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    K12-9 (CANP) - K12-6 (CPUB)
    G - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    K12-8 (CANN) - K12-6 (CPUB)
    GR - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


OUTER MIRROR CONTROL ECU ASSEMBLY (for Front Passenger Side) (w/ Seat Position Memory System)

B381655E06


Text in Illustration 
*a
Component without harness connected
(Outer Mirror Control ECU Assembly (for Front Passenger Side))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. C262706E51
  3. Disconnect the J10 outer mirror control ECU assembly (for front passenger side) connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Outer Mirror Control ECU Assembly (for Front Passenger Side))

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J10-9 (CANP) - J10-8 (CANN)
    P - GR
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    J10-9 (CANP) - J10-7 (GND)
    P - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    J10-8 (CANN) - J10-7 (GND)
    GR - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    J10-9 (CANP) - J10-6 (CPUB)
    P - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    J10-8 (CANN) - J10-6 (CPUB)
    GR - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


POSITION CONTROL ECU AND SWITCH ASSEMBLY (for Driver Side) (w/ Seat Position Memory System)

B219506E54


Text in Illustration 
*a
Component without harness connected
(Position Control ECU and Switch Assembly (for Driver Side))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the e11 and e12 position control ECU and switch assembly (for driver side) connectors.


    C204065E34


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Position Control ECU and Switch Assembly (for Driver Side))
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    e12-8 (CANP) - e12-7 (CANN)
    L - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    e12-8 (CANP) - e11-2 (GND)
    L - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    e12-7 (CANN) - e11-2 (GND)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    e12-8 (CANP) - e11-7 (+B)
    L - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    e12-7 (CANN) - e11-7 (+B)
    W - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System)

E233761E34


Text in Illustration 
*a
Component without harness connected
(Blind Spot Monitor Sensor RH)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the O43 blind spot monitor sensor RH connector.


    C250047E10


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Blind Spot Monitor Sensor RH)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O43-2 (CA1P) - O43-7 (CA1N)
    R - B
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    O43-2 (CA1P) - O43-10 (BRGD)
    R - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    O43-7 (CA1N) - O43-10 (BRGD)
    B - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    O43-2 (CA1P) - I39-16 (BAT)
    R - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    O43-7 (CA1N) - I39-16 (BAT)
    B - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher