STARTER (for 1.6 kW Type) > INSPECTION |
| 1. INSPECT STARTER ASSEMBLY |
Perform a pull-in test.
Disconnect the lead wire from terminal C.
![]() |
Connect the battery to the magnet starter switch as shown in the illustration. Check that the clutch pinion gear extends.
| *1 | Terminal 50 |
| *2 | Terminal C |
| *3 | Body |
![]() |
Perform the holding test.
Maintain the battery connections of the pull-in test above, but disconnect the negative (-) lead from terminal C. Check that the pinion gear remains extended.
| *1 | Terminal 50 |
| *2 | Terminal C |
| *3 | Body |
![]() |
Check the clutch pinion gear return.
Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
If the clutch pinion gear does not return, replace the magnet starter switch assembly.
| *1 | Terminal 50 |
| *2 | Terminal C |
| *3 | Body |
![]() |
Perform a no-load performance test.
Connect the lead wire to terminal C with the nut. Make sure that the lead is not grounded.
| *1 | Terminal 30 |
| *2 | Terminal 50 |
Clamp the starter in a vise.
Connect the battery and an ammeter to the starter as shown in the illustration.
Check that the starter rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.
| 2. INSPECT STARTER CLUTCH |
![]() |
Check the starter clutch.
Rotate the clutch pinion gear counterclockwise and check that it turns freely. Try to rotate the clutch pinion gear clockwise and check that it locks.
| *a | Lock |
| *b | Free |
| 3. INSPECT MAGNET STARER SWITCH ASSEMBLY |
![]() |
Inspect the plunger.
Push in the plunger and check that it returns quickly to its original position.
If necessary, replace the magnet starter switch assembly.
![]() |
Inspect the pull-in coil.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Terminal 50 - Terminal C | Always | Below 1 Ω |
| *1 | Terminal 50 |
| *2 | Terminal C |
![]() |
Inspect the holding coil.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Terminal 50 - Switch body | Always | Below 2 Ω |
| *1 | Terminal 50 |
| *2 | Body |
| 4. INSPECT STARTER ARMATURE ASSEMBLY |
Inspect the commutator for an open circuit.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Segment - Segment | Always | Below 1 Ω |
| *1 | Segment |
Inspect the commutator for a short circuit.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Commutator - Armature coil core | Always | 10 kΩ or higher |
| *1 | Commutator |
| *2 | Armature coil core |
Check the surface of the commutator for dirt and burns.
If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.
![]() |
Using a vernier caliper, measure the commutator length.
| *a | Length |
| 5. INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY |
![]() |
Using a vernier caliper, measure the brush length.
| *a | Length |
![]() |
Inspect the insulation.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Positive (+) brush - Negative (-) brush | Always | 10 kΩ or higher |