Home › Engine / Hybrid System · 6AR-FSE › STARTING › STARTER

STARTER > INSPECTION

for Preparation Click here



1. INSPECT STARTER ASSEMBLY

CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.

NOTICE:
Perform each of the following tests within 3 to 5 seconds to prevent the coil from burning out.



  1. Perform a pull-in test.

    1. Remove the nut, and disconnect the field coil lead wire from terminal C.



    2. A210436E08
    3. Connect a battery to the magnet switch as shown in the illustration. Check that the clutch pinion gear moves outward.
      Text in Illustration 
      *a
      Terminal 50
      *b
      Terminal C
      *c
      Starter Body
      V100135
      Moves outward
      If the clutch pinion gear does not move outward, replace the repair service starter kit.



  1. Perform a hold-in test.



      A210437E09
    1. While maintaining the battery connections of the pull-in test, disconnect the negative (-) lead from terminal C. Check that the clutch pinion gear does not return inward.
      Text in Illustration 
      *a
      Terminal 50
      *b
      Terminal C
      *c
      Starter Body
      V100135
      Disconnect
      If the clutch pinion gear returns inward, replace the repair service starter kit.



  1. Perform a return test.



      A309189E02
    1. Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
      Text in Illustration 
      *a
      Terminal 50
      *b
      Terminal C
      *c
      Starter Body
      V100135
      Disconnect
      V100136
      Returns inward
      If the clutch pinion gear does not return inward, replace the repair service starter kit.



  1. Perform a no-load performance test.

    1. Connect the field coil lead wire to terminal C with the nut.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    2. Secure the starter assembly in a vise between aluminum plates.

      NOTICE:
      Ensure that the starter assembly is secured in the vise to prevent it from falling out.



    3. A309183E08
    4. Connect the battery and an ammeter to the starter assembly as shown in the illustration.
       
      *a
      Terminal 50
      *b
      Terminal 30
      *c
      Starter Body

      NOTICE:
      Do not allow any lead to get caught as the clutch pinion gear operates.

    5. Check that the starter assembly operates smoothly and steadily while the clutch pinion gear is moving outward.
      Measure the current according to the value(s) in the table below.

      Standard Current:
      Tester Connection
      Condition
      Specified Condition
      Battery positive (+) terminal - Terminal 30 - Terminal 50
      11.5 V
      Below 90 A

      If the result is not as specified, replace the starter assembly.



2. INSPECT REPAIR SERVICE STARTER KIT


    A058586
  1. Check the plunger.

    1. Push in the plunger and check that it returns quickly to its original position.
      If the plunger does not operate as specified, replace the repair service starter kit.



    A079725E35
  1. Check the pull-in coil for an open circuit.
    Text in Illustration 
    *a
    Terminal 50
    *b
    Terminal C

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Terminal C
      Always
      Below 1 Ω

      If the result is not as specified, replace the repair service starter kit.



    A079726E28
  1. Check the holding coil for an open circuit.
    Text in Illustration 
    *a
    Terminal 50
    *b
    Magnet Switch Body

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Magnet switch body
      Always
      Below 2 Ω

      If the result is not as specified, replace the repair service starter kit.



3. INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the commutator appearance.
    If the surface is dirty or burnt, restore it with sandpaper (400-grit) or on a lathe.



    A295764E04
  1. Check the commutator for an open circuit.
    Text in Illustration 
    *a
    Segment

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      Always
      Below 1 Ω

      If the result is not as specified, replace the starter armature assembly.



    A295765E05
  1. Check the commutator for a short circuit.
    Text in Illustration 
    *a
    Segment
    *b
    Starter Armature Core

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Starter armature core
      Always
      Below 1 Ω

      If the result is not as specified, replace the starter armature assembly.



    A058584E29
  1. Using a vernier caliper, measure the commutator length.
    Text in Illustration 
    *a
    Length

    Standard Length:
    3.1 mm (0.122 in.)

    Maximum Length:
    3.8 mm (0.150 in.)

    If the length is greater than the maximum, replace the starter armature assembly.



4. INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY


    A076677E24
  1. Check the brush length.
    Text in Illustration 
    *a
    Length

    1. Using a vernier caliper, measure the brush length.

      Standard Length:
      9.0 mm (0.354 in.)

      Minimum Length:
      4.0 mm (0.157 in.)

      If the length is less than the minimum, replace the starter commutator end frame assembly.



    A079766E18
  1. Check the brush insulation.
    Text in Illustration 
    *a
    Positive (+) Brush
    *b
    Negative (-) Brush

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Positive (+) brush - Negative (-) brush
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter commutator end frame assembly.



5. INSPECT STARTER CLUTCH


    A081655E13
  1. Rotate the clutch pinion gear counterclockwise and check that it turns freely. Try to rotate the clutch pinion gear clockwise and check that it locks.
    Text in Illustration 
    *a
    Lock
    *b
    Free
    If the clutch pinion gear does not operate as specified, replace the No. 2 repair service starter kit.