Home › Engine / Hybrid System ยท 2AR-FE › STARTING › STARTER (for 1.6 kW Type)

STARTER (for 1.6 kW Type) > REASSEMBLY

for Preparation Click here



1. INSTALL PLANETARY GEAR


    A197679E06
  1. Apply high-temperature grease to the planetary gears and pin parts of the planetary shaft.
    Text in Illustration 
    V100135
    High-temperature grease

  1. Install the 3 planetary gears.



2. INSTALL RUBBER SEAL


    A194763
  1. Install the rubber seal to the repair service starter kit.



3. INSTALL STARTER ARMATURE ASSEMBLY


    A197678E10
  1. Apply high-temperature grease to the washer and the armature shaft.
    Text in Illustration 
    V100135
    High-temperature grease



    A135954E04
  1. Apply high-temperature grease to the plate washer and bearing, as shown in the illustration.
    Text in Illustration 
    V100135
    High-temperature grease



    A194762E04
  1. Install the starter armature assembly to the starter commutator end frame assembly.
    Text in Illustration 
    *1
    Snap Ring Pliers

  1. Install the washer.

  1. Using snap ring pliers, securely install a new snap ring to the armature shaft groove.

    NOTICE:
    Be sure to install the snap ring, properly because it easily expands.



    A194767E03
  1. Using a vernier caliper, measure the length of the snap ring.
    Text in Illustration 
    *a
    Length

    Maximum length:
    5.0 mm (0.197 in.)

    If the length is more than the maximum, replace the snap ring with a new one.



4. INSTALL STARTER COMMUTATOR END FRAME COVER


    A197189
  1. Install the starter commutator end frame cover to the starter commutator end frame assembly.



5. INSTALL STARTER ARMATURE PLATE


    A194768E03
  1. Insert the armature plate into the starter yoke assembly.
    Text in Illustration 
    *a
    Keyway
    *b
    Key

  1. Align the keyway of the starter armature plate with the key inside the starter yoke, and install the starter armature plate.



6. INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY


    A197184E03
  1. Align the rubber of the end frame with the cutout of the starter yoke assembly.
    Text in Illustration 
    *a
    Cutout
    *b
    Rubber

  1. Install the starter commutator end frame assembly to the starter yoke assembly.

    NOTICE:
    The magnet of the starter yoke assembly may attract the starter armature when the starter commutator end assembly frame is installed, causing the magnet to break.



7. INSTALL STARTER YOKE ASSEMBLY


    A197185E03
  1. Align the protrusion of the starter yoke assembly with the cutout of the repair service starter kit.
    Text in Illustration 
    *a
    Protrusion
    *b
    Cutout



    A194758
  1. Install the starter yoke assembly with the 2 through-bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



8. INSTALL MAGNET STARTER SWITCH ASSEMBLY


    A197681E04
  1. Apply high-temperature grease to the plunger and the lever.
    Text in Illustration 
    V100135
    High-temperature grease



    A197186
  1. Pull the pinion gear and push down the lever.



    A197187E03
  1. Temporarily install the magnet starter switch assembly by hooking the plunger into the upper side of the pinion drive lever.
    Text in Illustration 
    *1
    Plunger
    *2
    Lever



    A194757
  1. Install the magnet starter switch assembly with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    A194756
  1. Connect the lead wire to the magnet starter switch assembly with the nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }