Home › Engine / Hybrid System · 2GR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0365    Camshaft Position Sensor "B" Circuit (Bank 1)

DTC    P0367    Camshaft Position Sensor "B" Circuit Low Input (Bank 1)

DTC    P0368    Camshaft Position Sensor "B" Circuit High Input (Bank 1)

DTC    P0390    Camshaft Position Sensor "B" Circuit (Bank 2)

DTC    P0392    Camshaft Position Sensor "B" Circuit Low Input (Bank 2)

DTC    P0393    Camshaft Position Sensor "B" Circuit High Input (Bank 2)

for Preparation Click here


DESCRIPTION

The VVT sensor (for exhaust camshaft) (EV1, EV2 signal) consists of a magnet and MRE (Magneto Resistance Element).
The exhaust camshaft has a timing rotor for the VVT sensor. When the exhaust camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
Then the ECM uses this data to control fuel injection duration, fuel injection timing and the Variable Valve Timing (VVT) system.

DTC No.
DTC Detection Condition
Trouble Area
P0365
P0390
No exhaust VVT sensor signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic).
  1. Open or short in VVT sensor (for exhaust camshaft) circuit
  2. VVT sensor (for exhaust camshaft)
  3. Exhaust camshaft
  4. Valve timing
  5. ECM
P0367
P0392
The output voltage of the exhaust VVT sensor (bank 1, 2) is less than 0.3 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor (for exhaust camshaft) circuit
  2. VVT sensor (for exhaust camshaft)
  3. ECM
P0368
P0393
The output voltage of the exhaust VVT sensor (bank 1, 2) is higher than 4.7 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor (for exhaust camshaft) circuit
  2. VVT sensor (for exhaust camshaft)
  3. ECM
Reference: Inspection using an oscilloscope
A207435E02

HINT:
EV1+ and EV2+ stand for the VVT sensor (for exhaust camshaft) signal, and NE+ stands for the crankshaft position sensor signal.

ECM Terminal Name
Between NE+ and NE-
Between EV1+ and VV1-
Between EV2+ and VV1-
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idling

MONITOR DESCRIPTION

If no pulse signal is transmitted by the VVT sensor (for exhaust camshaft) despite the camshaft rotating, or the rotation of the exhaust camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.
Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY


Required Sensors/Components (Main)
VVT sensor (for exhaust camshaft)
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the engine switch on (IG) and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the tester on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more.
  8. Enter the following menus: Powertrain / Engine / DTC.
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P0365, P0367, P0368, P0390, P0392 or P0393.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
  1. If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  4. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VVT SENSOR (FOR EXHAUST CAMSHAFT))


    A194108E73
  1. Disconnect the VVT sensor (for exhaust camshaft) connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E53-3 (VC2) - Body ground
    Engine switch on (IG)
    4.5 to 5.5 V
    E59-3 (VC2) - Body ground
    Engine switch on (IG)
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Bank 1
    *2
    Bank 2
    *a
    Front view of wire harness connector
    (to VVT Sensor (for Exhaust Camshaft))



NG
Go to step 8
OK


2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
  1. Disconnect the VVT sensor (for exhaust camshaft) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E53-1 (EX+) - E26-79 (EV1+)
    Always
    Below 1 Ω
    E53-2 (EX-) - E26-110 (VV1-)
    Always
    Below 1 Ω
    E59-1 (EX+) - E26-80 (EV2+)
    Always
    Below 1 Ω
    E59-2 (EX-) - E26-110 (VV1-)
    Always
    Below 1 Ω
    E53-1 (EX+) or E26-79 (EV1+) - Body ground
    Always
    10 kΩ or higher
    E53-2 (EX-) or E26-110 (VV1-) - Body ground
    Always
    10 kΩ or higher
    E59-1 (EX+) or E26-80 (EV2+) - Body ground
    Always
    10 kΩ or higher
    E59-2 (EX-) or E26-110 (VV1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR EXHAUST CAMSHAFT))


    BR03795E17
  1. Check the VVT sensor (for exhaust camshaft) installation.

    OK:
    VVT sensor is installed correctly.



NG
SECURELY REINSTALL VVT SENSOR (FOR EXHAUST CAMSHAFT) (Click here)
OK


4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
  1. Inspect the timing rotor of the exhaust camshaft.

    OK:
    Camshaft timing rotor does not have any cracks or deformation.

    HINT:
    Perform "Inspection After Repair" after replacing the exhaust camshaft (Click here).



NG
REPLACE EXHAUST CAMSHAFT (Click here)
OK


5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)


    A135015E03
  1. Remove the cylinder head cover sub-assemblies RH and LH (Click here).

  1. Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.

    HINT:
    If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

    OK:
    The timing marks on the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned as shown in the illustration.

    Text in Illustration 
    *1
    Timing Mark



NG
ADJUST VALVE TIMING (Click here)
OK


6.REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT)
  1. Replace the VVT sensor (for exhaust camshaft) (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367, P0368, P0390, P0392 OR P0393)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Start the engine.

  1. Turn the tester on.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0365, P0367, P0368, P0390, P0392 or P0393 is output
    A
    DTC is not output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
END
A

REPLACE ECM (Click here)  

8.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
  1. Disconnect the VVT sensor (for exhaust camshaft) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E53-3 (VC2) - E26-111 (VCV1)
    Always
    Below 1 Ω
    E59-3 (VC2) - E26-111 (VCV1)
    Always
    Below 1 Ω
    E53-3 (VC2) or E26-111 (VCV1) - Body ground
    Always
    10 kΩ or higher
    E59-3 (VC2) or E26-111 (VCV1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)