Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Low Beam Headlight Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the low beam headlights via the H-LP relay.

WIRING DIAGRAM


for HID Headlight:

E301514E04


for LED Headlight:

E301514E06


for Halogen Headlight:

E314640E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Headlight Relay
    Low beam headlights
    ON/OFF
    -

    OK:
    Headlight relay operates. (Low beam headlights illuminate.)



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT H-LP RELAY
  1. Remove the H-LP relay from the engine room relay block and junction block assembly.



    E223988E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage applied between terminals 1 and 2
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (H-LP Relay)



NG
REPLACE H-LP RELAY
OK


3.CHECK HARNESS AND CONNECTOR (H-LP MAIN FUSE - H-LP RELAY)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Relay Terminal 2 - Body ground
    Always
    11 to 14 V
    Relay Terminal 5 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)
  1. for HID Headlight:

    1. Disconnect the A24 headlight assembly LH connector.

    2. Disconnect the A66 headlight assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Relay Terminal 3 - A24-2 (LO)
      Always
      Below 1 Ω
      Relay Terminal 3 - A66-2 (LO)
      Always
      Below 1 Ω
      Relay Terminal 3 - Body ground
      Always
      10 kΩ or higher

  1. for LED Headlight:

    1. Disconnect the A91 headlight assembly LH connector.

    2. Disconnect the A95 headlight assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Relay Terminal 3 - A91-1 (LO)
      Always
      Below 1 Ω
      Relay Terminal 3 - A95-1 (LO)
      Always
      Below 1 Ω
      Relay Terminal 3 - Body ground
      Always
      10 kΩ or higher

  1. for Halogen Headlight:

    1. Disconnect the A17 headlight assembly LH connector.

    2. Disconnect the A60 headlight assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Relay Terminal 3 - A17-2 (LO)
      Always
      Below 1 Ω
      Relay Terminal 3 - A60-2 (LO)
      Always
      Below 1 Ω
      Relay Terminal 3 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3D instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Relay Terminal 1 - 3D-12
    Always
    Below 1 Ω
    Relay Terminal 1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    E182506E27
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3D-12 - MB-15 (HRLY)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)