Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT (for TMC, TMMR Made)

REAR WHEEL ALIGNMENT (for TMC, TMMR Made) > ADJUSTMENT

for Preparation Click here



1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold Tire Inflation Pressure:

    Tire Size
    4 passengers or less
    5 passengers
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    215/60R16 95V
    230 (2.3, 33)
    230 (2.3, 33)*1
    240 (2.4, 35)*2
    270 (2.7, 39)*3
    215/55R17 93V
    230 (2.3, 33)*1, *2
    240 (2.4, 35)*3
    230 (2.3, 33)
    230 (2.3, 33)*1
    260 (2.6, 38)*2
    290 (2.9, 42)*3

    *1: For driving under 160 km/h (100 mph)
    *2: For driving at 160 km/h (100 mph) to 180 km/h (112 mph)
    *3: For driving at 180 km/h (112 mph) to 210 km/h (131 mph)



    C137874
  1. Using a dial indicator, check the runout of the tires.

    Maximum Tire Runout:
    1.4 mm (0.0551 in.)



2. MEASURE VEHICLE HEIGHT


C239047E01

NOTICE:
  1. Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
  2. Be sure to perform measurement on a level surface.
  3. If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
  4. Inspect while the vehicle is unloaded.
  5. The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  1. Measure the vehicle height.

    Measurement points:
    1. A: Ground clearance of front wheel center
    1. B: Ground clearance of lower No. 2 suspension arm bushing set bolt center
    1. C: Ground clearance of rear wheel center
    1. D: Ground clearance of strut rod set bolt center

    Vehicle Height (Unloaded Vehicle):

    Tire Size
    Front A - B
    Rear C - D
    215/60R16
    112 mm (4.41 in.)
    112 mm (4.41 in.)*1
    114 mm (4.49 in.)*3
    40 mm (1.57 in.)
    41 mm (1.61 in.)*1
    40 mm (1.57 in.)*3
    215/55R17
    116 mm (4.57 in.)
    113 mm (4.45 in.)*1
    117 mm (4.61 in.)*2
    46 mm (1.81 in.)
    42 mm (1.65 in.)*1
    47 mm (1.85 in.)*2

    *1: for Russia 2AR-FE
    *2: for Russia 2GR-FE
    *3: for Russia 6AR-FSE



3. INSPECT CAMBER

NOTICE:
Inspect while the vehicle is unloaded.



    C107736E10
  1. Install a camber-caster-kingpin gauge.
    Text in Illustration 
    *a
    Camber-caster-kingpin Gauge

  1. Inspect the camber.

    Camber (Unloaded Vehicle):

    Tire Size
    Camber Inclination
    Right-left Difference
    215/60R16
    -1°08' +/- 45' (-1.13° +/- 0.75°)
    -1°09' +/- 45' (-1.15° +/- 0.75°)*1
    -1°07' +/- 45' (-1.12° +/- 0.75°)*3
    45' (0.75°) or less
    215/55R17
    -1°11' +/- 45' (-1.18° +/- 0.75°)
    -1°09' +/- 45' (-1.15° +/- 0.75°)*1
    -1°12' +/- 45' (-1.20° +/- 0.75°)*2

    *1: for Russia 2AR-FE
    *2: for Russia 2GR-FE
    *3: for Russia 6AR-FSE

    HINT:
    Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.



4. INSPECT TOE-IN

NOTICE:
Inspect while the vehicle is unloaded.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  1. Release the parking brake and move the shift lever to N.

  1. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)



    C188968E06
  1. Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).
    Text in Illustration 
    *a
    Tread Center Mark
    *b
    Dimension B
    V100135
    Front of the Vehicle

  1. Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

    HINT:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step A again.



    C188969E06
  1. Measure the distance between the tread center marks on the front of the rear wheels (dimension A).
    Text in Illustration 
    *a
    Dimension A
    V100135
    Front of the Vehicle

    Toe-in (Unloaded Vehicle):
    Specified Condition
    C + D: 0°22' +/- 0°11' (0.37° +/- 0.18°)
    B - A: 4.0 +/- 2.0 mm (0.157 +/- 0.0787 in.)

    HINT:
    Measure "B - A" only when "C + D" cannot be measured.

    If the toe-in is not within the specified range, adjust it at the rear No. 2 suspension arms.



5. ADJUST TOE-IN


    C239066
  1. Measure the lengths of the right and left rear No. 2 suspension arms.

    Standard Difference:
    1.5 mm (0.0591 in.) or less



    C239067
  1. Loosen the 2 lock nuts.

  1. If the length difference between the left and right rear No. 2 suspension arm assemblies is not within the specified range, adjust it by following the procedures below.

    1. If the toe-in measurement is greater than the specified range (too much toe-out), extend the shorter rear No. 2 suspension arm by rotating the adjusting tube so that the length difference is within the specified range.

    2. If the toe-in measurement is less than the specified range (too much toe-in), shorten the longer rear No. 2 suspension arm by rotating the adjusting tube so that the length difference is within the specified range.

    3. Measure the toe-in.



    C317577E01
  1. Turn the right and left adjusting tubes by an equal amount to adjust toe-in.

    Toe-in (Unloaded Vehicle):
    Specified Condition
    C + D: 0°22' +/- 0°11' (0.37° +/- 0.18°)
    B - A: 4.0 +/- 2.0 mm (0.157 +/- 0.0787 in.)

    Text in Illustration 
    V100135
    Front of the Vehicle

    HINT:
    1. Perform adjustments so that the value is as close as possible to the median of the specified range.
    2. One turn of each adjusting tube will adjust the toe-in by approximately 10.8 mm (0.425 in.).

  1. Tighten the lock nuts while securing the adjusting tube in the order indicated below:

    1. Tighten the outside lock nut.
    2. Tighten the inside lock nut.
    3. Retighten the outside lock nut.

    Torque:
    56 N*m{ 570 kgf*cm , 41 ft.*lbf }