Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM

AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM > Headlight Beam Level Control Actuator Circuit

for Preparation Click here


DESCRIPTION

The headlight leveling ECU assembly actuates the headlight leveling motors according to vehicle conditions.

WIRING DIAGRAM


for TMC, TMMR Made:

E220279E02


for TMMK Made:

E220279E17


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / HL AutoLeveling / Active Test.

  1. Check that the leveling motors operate.

    HL AutoLeveling 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Drive The Leveling Motor UP
    Leveling motor upward operation
    ON/OFF
    ON: Moves up
    OFF: Stops
    Drive The Leveling Motor DOWN
    Leveling motor downward operation
    ON/OFF
    ON: Moves down
    OFF: Stops

    OK:
    Headlight leveling motors operate normally.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING MOTOR - HEADLIGHT LEVELING ECU ASSEMBLY)
  1. for TMC, TMMR Made:

    1. Disconnect the A34 headlight leveling ECU assembly connector.

    2. Disconnect the LH side or RH side headlight leveling motor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      LH Side 
      Tester Connection
      Condition
      Specified Condition
      A34-18 (LHE) - A18-2 (LHM+)
      Always
      Below 1 Ω
      A34-11 (LH+) - A18-3 (LHB1)
      Always
      Below 1 Ω
      A34-24 (LH-) - A18-1 (LHE)
      Always
      Below 1 Ω
      A34-18 (LHE) - Body ground
      Always
      10 kΩ or higher
      A34-11 (LH+) - Body ground
      Always
      10 kΩ or higher
      A34-24 (LH-) - Body ground
      Always
      10 kΩ or higher
      RH Side 
      Tester Connection
      Condition
      Specified Condition
      A34-17 (RHE) - A62-2 (RHM+)
      Always
      Below 1 Ω
      A34-10 (RH+) - A62-3 (RHB1)
      Always
      Below 1 Ω
      A34-23 (RH-) - A62-1 (RHE)
      Always
      Below 1 Ω
      A34-17 (RHE) - Body ground
      Always
      10 kΩ or higher
      A34-10 (RH+) - Body ground
      Always
      10 kΩ or higher
      A34-23 (RH-) - Body ground
      Always
      10 kΩ or higher

  1. for TMMK Made:

    1. Disconnect the A34 headlight leveling ECU assembly connector.

    2. Disconnect the LH side or RH side headlight leveling motor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      LH Side 
      Tester Connection
      Condition
      Specified Condition
      A34-18 (LHE) - A90-2 (LHM+)
      Always
      Below 1 Ω
      A34-11 (LH+) - A90-3 (LHB1)
      Always
      Below 1 Ω
      A34-24 (LH-) - A90-1 (LHE)
      Always
      Below 1 Ω
      A34-18 (LHE) - Body ground
      Always
      10 kΩ or higher
      A34-11 (LH+) - Body ground
      Always
      10 kΩ or higher
      A34-24 (LH-) - Body ground
      Always
      10 kΩ or higher
      RH Side 
      Tester Connection
      Condition
      Specified Condition
      A34-17 (RHE) - A94-2 (RHM+)
      Always
      Below 1 Ω
      A34-10 (RH+) - A94-3 (RHB1)
      Always
      Below 1 Ω
      A34-23 (RH-) - A94-1 (RHE)
      Always
      Below 1 Ω
      A34-17 (RHE) - Body ground
      Always
      10 kΩ or higher
      A34-10 (RH+) - Body ground
      Always
      10 kΩ or higher
      A34-23 (RH-) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HEADLIGHT LEVELING MOTOR
  1. Replace the headlight leveling motor with a new or a known good one (for TMC, TMMR Made: Click here), (for TMMK Made: Click here).

  1. Perform the active test of the leveling motors.

    OK:
    Headlight leveling motors operate normally.



NG
REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)
OK

END (HEADLIGHT LEVELING MOTOR WAS DEFECTIVE)