Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows)

POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / (desired system) / Data List.

  5. Read the Data List according to the display on the GTS.

    Master Switch 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver door power window auto switch signal / OFF or ON
    OFF: Driver door power window auto switch not being operated
    ON: Driver door power window auto switch being operated
    -
    P Door P/W Auto SW
    Front passenger door power window auto up and down switch signal / OFF or ON
    OFF: Front passenger door power window auto switch not being operated
    ON: Front passenger door power window auto switch being operated
    -
    P Door P/W Up SW
    Front passenger door power window manual up switch signal / OFF or ON
    OFF: Front passenger door power window manual up switch not being operated
    ON: Front passenger door power window manual up switch being operated
    -
    P Door P/W Down SW
    Front passenger door power window manual down switch signal / OFF or ON
    OFF: Front passenger door power window manual down switch not being operated
    ON: Front passenger door power window manual down switch being operated
    -
    Window Lock Switch Status
    Window lock switch signal / OFF or ON
    OFF: Window lock switch UNLOCK position
    ON: Window lock switch LOCK position
    -
    Number of Trouble Codes
    Number of trouble codes / Min.: 0 to Max.: 255
    Number of DTCs is displayed
    -

    D-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver door power window auto switch signal / OFF or ON
    OFF: Driver door power window auto switch not being operated
    ON: Driver door power window auto switch being operated
    -
    D Door P/W Up SW
    Driver door power window manual up switch signal / OFF or ON
    OFF: Driver door power window manual up switch not being operated
    ON: Driver door power window manual up switch being operated
    -
    D Door P/W Down SW
    Driver door power window manual down switch signal / OFF or ON
    OFF: Driver door power window manual down switch not being operated
    ON: Driver door power window manual down switch being operated
    -
    Glass Position (Close - 1/4)
    Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (1/4 - 2/4)
    Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (2/4 - 3/4)
    Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (3/4 - Open)
    Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    D Window Auto Up
    Auto up operation using the power window regulator master switch assembly / OFF or ON
    Customize setting displayed
    -
    D Window Auto Down
    Auto down operation using the power window regulator master switch assembly / OFF or ON
    Customize setting displayed
    -
    Number of Trouble Codes
    Number of trouble codes / Min.: 0 or Max.: 255
    Number of DTCs is displayed
    -

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front passenger door power window auto switch signal / OFF or ON
    OFF: Front passenger door power window auto switch not being operated
    ON: Front passenger door power window auto switch being operated
    -
    P Door P/W Up SW
    Front passenger door power window manual up switch signal / OFF or ON
    OFF: Front passenger door power window manual up switch not being operated
    ON: Front passenger door power window manual up switch being operated
    -
    P Door P/W Down SW
    Front passenger door power window manual down switch signal / OFF or ON
    OFF: Front passenger door power window manual down switch not being operated
    ON: Front passenger door power window manual down switch being operated
    -
    Glass Position (Close - 1/4)
    Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (1/4 - 2/4)
    Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (2/4 - 3/4)
    Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (3/4 - Open)
    Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    P Window Auto Up
    Auto up operation using the power window regulator master switch assembly / OFF or ON
    Customize setting displayed
    -
    P Window Auto Down
    Auto down operation using the power window regulator master switch assembly / OFF or ON
    Customize setting displayed
    -
    Number of Trouble Codes
    Number of trouble codes / Min.: 0 or Max.: 255
    Number of DTCs is displayed
    -

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG SW
    Engine switch status / OFF or ON
    OFF: Engine switch off
    ON: Engine switch on (IG)
    "OFF" is displayed even though the engine switch is turned to ACC.
    FR Door Courtesy SW
    Front door courtesy light switch RH / OFF or ON
    OFF: Front door RH closed
    ON: Front door RH open
    -
    FL Door Courtesy SW
    Front door courtesy light switch LH / OFF or ON
    OFF: Front door LH closed
    ON: Front door LH open
    -
    Communication D-Door Motor
    Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) / STOP or OK
    STOP: Communication stopped
    OK: Normal communication
    -
    Communication P-Door Motor
    Connection status between power window regulator motor assembly (for front passenger door) and main body ECU (multiplex network body ECU) / STOP or OK
    STOP: Communication stopped
    OK: Normal communication
    -
    Communication Master SW
    Connection status between power window regulator master switch assembly and main body ECU (multiplex network body ECU) / STOP or OK
    STOP: Communication stopped
    OK: Normal communication
    -


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / (desired system) / Active Test.

  5. Perform the Active Test according to the display on the GTS.

    CAUTION:
    Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


    D-Door Motor 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -

    P-Door Motor 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    IG OFF P/W Control Permission Output
    Power window
    OFF / ON
    Perform this Active Test with the engine switch off